HTHiroki Takahashi

Hiroki Takahashi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hiroki Takahashi has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Synthesis and Evaluation of Layered Ni–Co and Ni–Co–Ni Electrodes Modified by Molten–Salt Al Deposition/Dissolution Technique for Electrochemical Applications

    by Dawid Kutyła, Michihisa Fukumoto, Hiroki Takahashi, Ryuu Takahashi, Katarzyna Skibińska, Piotr Żabiński

    Porous bilayer Ni–Co and sandwiched Ni–Co–Ni electrodes were fabricated by combining aqueous electrodeposition with high-temperature molten-salt Al deposition and subsequent electrochemical dissolution in NaCl–KCl–AlF3 melt at 750 °C. The study aimed to determine how the initial layer architecture controls phase evolution, porous structure formation, and hydrogen evolution performance in alkaline media. SEM/EDS and XRD analyses showed that the two electrode designs followed different reaction pathways during molten-salt treatment. In the Ni–Co system, Al reacted predominantly with Co, leading mainly to Co–Al intermetallic formation and, after dissolution, to a highly open coral-like porous network. In contrast, the Ni–Co–Ni architecture promoted mainly Ni–Al phase formation and produced a more compact porous surface with a Ni-rich outer layer. Despite these morphological differences, both layered porous electrodes outperformed untreated Ni and porous Ni in 1 M NaOH. At −0.6 V vs. RHE, porous Ni–Co and NiCo–Ni reached current densities of −162 and −141 mA·cm−2, respectively, compared with −87 mA·cm for porous Ni and −45 mA·cm for flat Ni. The Ni–Co–Ni sandwiched electrode showed the most favourable HER kinetics and benchmark performance, with the lowest Tafel slope (111 mV·dec) and the lowest potentials at −10 and −100 mA·cm (−0.132 and −0.556 V, respectively). These results demonstrate that the electrocatalytic response of molten-salt-derived porous Ni-based electrodes is governed not only by porosity development but also by the spatial arrangement of metallic layers prior to Al infiltration and dealloying.

  • Open Access

    Electrochemical Urea Oxidation on Porous Ni and Ni–M (M = Ir, Pt) Electrodes Obtained via Molten-Salt Treatment Technique

    by Dawid Kutyła, Michihisa Fukumoto, Hiroki Takahashi, Ryuu Takahashi, Katarzyna Skibińska, Piotr Żabiński

    Porous Ni, Ni–Ir, and Ni–Pt electrodes were prepared on Ni substrates by molten-salt Al co-deposition followed by dealloying. SEM/EDS and XRD confirmed a Raney-type porous network with Ir or Pt present across the layer. A urea oxidation reaction (UOR) was tested in 1 M NaOH + 0.33 M urea by cyclic voltammetry and chronoamperometry at +0.40 V vs. SCE (60 min). Smooth Ni showed near-zero current. Porous Ni resulted in ~11 mA cm−2 initially and ~9 mA cm−2 after 60 min. Porous Ni–Ir started at ~7 mA cm−2 and fell to ~2 mA cm−2 within 5 min, indicating fast deactivation, likely due to Ir-oxide formation that suppresses the Ni2+/Ni3+ redox couple. Porous Ni–Pt remained at ~11 mA cm−2 over 60 min, consistent with a stable Ni–Pt effect in which Pt aids urea adsorption/activation while Ni provides the redox path for oxidation. Overall, Pt improves UOR performance, whereas Ir lowers it under these conditions.


  • Open Access

    In-situ Observation of the Environmental Resistance of Pure Iron Using Hydrogen and Oxygen Sensors in the Environment Simulating Hydrogen Combustion

    by Michihisa Fukumoto, Hiroki Takahashi

    The environmental resistance of pure iron was evaluated with oxygen and hydrogen sensor installed after the oxidation furnace. The amount of introduced oxygen was precisely controlled by oxygen pump-sensor at the front stage of the oxidation furnace and the reaction with hydrogen was analyzed. As a result, when oxygen was supplied, a reaction between hydrogen and oxygen occurred, but when sufficient oxygen was not supplied, a hydrogen-vapor environment was created and oxidation was not accelerated. However, when the amount of supplied oxygen was excessive, the environment became oxygen-steam environment and the oxidation was accelerated. At that time, it was clarified that the oxidation by oxygen was dominant under the oxygen-water vapor environment, and the mass gain increased. In addition, the border of the region dominated by oxygen oxidation and that by steam oxidation was clarified by precisely controlling the amount of supplied oxygen by the oxygen pump sensor.

  • Open Access

    Catalytic Activity Evaluation of the Molten Salt-Modified Novel Ni Electrodes for Urea Electrooxidation in Alkaline Solutions

    by Dawid Kutyła, Michihisa Fukumoto, Hiroki Takahashi, Marek Wojnicki, Piotr Żabiński

    The presented paper characterized the molten salt-modified Ni electrode with excellent catalytic activity towards alkaline urea electrooxidation reaction. The electrodes were modified by electrodeposition of Al from molten salt electrolytes containing NaCl-KCl-AlF3 at a temperature of 750 °C and applied potential of −1.9 V. The porous surface was obtained by anodic polarization with a potential of −0.4 V until the anodic current was equal to 0 mAcm−2. The prepared deposits’ structure, surface morphology, and composition were analyzed using scanning electron microscopy (SEM) and X-ray diffraction (XRD). Anodic polarization was applied to assess the electrocatalytic activity and elucidate the urea electrooxidation mechanism in 1 M KOH + 0.33 M urea solution. The nanocrystalline structure, fine grain size, and microcracks on the surface of the studied electrodes contributed to their notably high electrochemically active surface area (ECSA). The cyclic voltammetry in the non-Faradaic regions of the samples shows that molten salt modification can increase the double layer capacitance of bare Ni plates by around ten times, from 0.29 mFcm−2 to 2.16 mFcm−2. Polarization of the electrodes in urea-containing KOH solution with potential of +1.52 V shows a significant difference in catalytic performance. For the bare nickel sample, the registered current density from the urea electrooxidation reaction was around +1 mAcm−2, and for the molten salt-modified one, it was +38 mAcm−2, which indicates the fact that the molten salt surface treatment can be a promising tool in tailoring the electrochemical properties of materials.


  • Open Access

    Catalytic Activity Evaluation of Molten Salt-Treated Stainless Steel Electrodes for Hydrogen Evolution Reaction in Alkaline Medium

    by Michihisa Fukumoto, Hiroki Takahashi, Dawid Kutyła, Marek Wojnicki, Piotr Żabiński

    The goal of this research is to fabricate a novel type of highly active porous electrode material, based on stainless steel and dedicated to water electrolyzers. The main novelty of the presented work is the innovative application of the molten salts treatment, which allows the design of a highly developed porous structure, which characterizes significantly higher catalytic activity than untreated steel substrates. The equimolar mixture of NaCl and KCl with 3.5 mol% AlF3 was used as the molten salt. The surface modification procedure includes the deposition of an Al layer with application at the potential of −1.8 V and following dissolution at −0.9 V, to create a porous alloy surface. The cathodic polarization measurements of the prepared porous stainless steel electrodes were measured in a 10 mass% KOH solution. Moreover, the amount of hydrogen generated during constant voltage electrolysis with a hydrogen sensor in situ was also measured. The porous stainless steel alloy showed higher current density at lower potentials in the cathodic polarization compared to untreated stainless steel. The cathodic polarization measurements in alkaline solution showed that the porous 304 stainless steel alloy is an excellent cathode material.


  • Open Access

    Oxidation Behavior of Pure Iron under Hydrogen Combustion Environment

    by Michihisa Fukumoto, Seiya Hara, Hiroki Takahashi

    The environmental resistance of pure iron was evaluated by an oxygen and hydrogen sensor installed after an oxidation furnace. The amount of introduced oxygen was precisely controlled by the oxygen pump sensor at the front stage of the oxidation furnace, and the reaction with hydrogen was analyzed. Thus, when oxygen was supplied, a reaction between hydrogen and oxygen occurred; however, when the supplied oxygen was not sufficient, a hydrogen-vapor environment was created, and oxidation was not accelerated. Conversely, when the amount of supplied oxygen was excessive, the environment became an oxygen–steam environment, and oxidation was accelerated. Therefore, this explained how the oxidation caused by oxygen was dominant under the oxygen–water vapor environment, and the oxidation weight gain increased. In addition, the border of the region dominated by oxygen oxidation and steam oxygen was clarified by precisely controlling the amount of oxygen supplied by the oxygen pump sensor.


  • Open Access

    Ammonia Oxidation Activity of Pt Alloy Thin Film Electrode in Alkaline Solution

    by Hikaru Sato, Yuya Naito, Michihisa Fukumoto, Hiroki Takahashi

    Hydrogen production using renewable energy is regarded as a key technology to achieve sustainable society. But hydrogen has a low volumetric energy density and it’s difficult to storage and transport. Therefore, ammonia normally produced by the Haber-Bosch process with hydrogen and nitrogen attracts much attention as hydrogen carrier. Although ammonia is toxic, it has a low risk because we can detect it immediately due to its characteristic smell when it leaks. So, a direct ammonia fuel cell (DAFC) that directly generates electricity from ammonia is expected to be a new power generation system. Pt is used as an anode catalyst for ammonia oxidation reaction in DAFC, but an alternative one is required because it is expensive and deactivated by adsorbed N species. In this study, we focused on Pt alloy anodes. We chose Al, Cu and Ni as alloying elements. We have discovered the improvement of ammonia oxidation activity by alloying Pt with other elements. Especially, Pt-11.6at.%Al showed the highest ammonia oxidation current, 7.33 mA cm-2, and it will be attractive candidate for DAFC.