Gilberto Martinez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Gilberto Martinez has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Jose Marcos Alonso
Department of Electrical Engineering, University of Oviedo, Asturias, Spain
6 shared publications - Rene Osorio
Computer Science and Engineering Department, University of Guadalajara, Ameca 46600, Mexico
6 shared publications - Marina S. Perdigao
Polytechnic Institute of Coimbra
4 shared publications J. Marcos Alonso
University of Oviedo, Electrical Eng. Dept., Campus de Viesques, Gijón, Asturias, Spain
2 shared publicationsJuan Vina
Electrical and Electronics Engineering Department, Universidad de Oviedo, Gijón, Spain
2 shared publicationsA.J. Martínez
Metal Mechanics Department Technological Institute of Zacatepec Tecnológico Street, number 27 ZC 62780 Zacatepec Morelos Mexico
1 shared publication
Latest Publications
- 16 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 6 (3) , 1106-1115
Analysis and Design of a Unidirectional Resonant Switched-Capacitor Step-Up Converter for OLED Lamp Driving Based on Variable Inductor
This paper presents an analysis and design of a unidirectional resonant switched capacitor (URSC) step-up converter for OLED lamp driving. The URSC converter includes a very small inductor in series with the switched capacitor to improve the switching behavior. Also, the URSC converter presents the advantages of high power density, higher efficiency compared to other SC converters, low output voltage and current ripples and low EMI noise, which make it adequate for driving OLED lamps. URSC is designed to operate in closed loop with constant current VI control technique. By working the resonant inductor as a VI, the OLED current can be regulated and dimmed because of resonant frequency change. Simulation and experimental results of the VI inductor, which are in a good agreement, and the results of a URSC step-up converter design example for a 21.8 W OLED lamps array supplied from 48Vdc are presented, where a maximum 92.97% efficiency is obtained.
- 16 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 6 (3) , 1106-1115
Analysis and Design of a Unidirectional Resonant Switched-Capacitor Step-Up Converter for OLED Lamp Driving Based on Variable Inductor
This paper presents an analysis and design of a unidirectional resonant switched capacitor (URSC) step-up converter for OLED lamp driving. The URSC converter includes a very small inductor in series with the switched capacitor to improve the switching behavior. Also, the URSC converter presents the advantages of high power density, higher efficiency compared to other SC converters, low output voltage and current ripples and low EMI noise, which make it adequate for driving OLED lamps. URSC is designed to operate in closed loop with constant current VI control technique. By working the resonant inductor as a VI, the OLED current can be regulated and dimmed because of resonant frequency change. Simulation and experimental results of the VI inductor, which are in a good agreement, and the results of a URSC step-up converter design example for a 21.8 W OLED lamps array supplied from 48Vdc are presented, where a maximum 92.97% efficiency is obtained.
- 20 April 2017
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 45 (11) , 1760-1772
Simplified electrical modelling of power LEDs for DC–DC converter analysis and simulation
Summary: This paper presents a model of power light emitting diodes (LEDs) based on electrical variables and considering the concept of LED ‘equivalent resistance’, which has previously been used in discharge lamp modelling and is suitable to achieve fast simulations of LED converter systems. The model can be obtained with only some simple electrical measurements, thus making its implementation quite straightforward. The proposed model is oriented to the electronic engineering area, and it has special application for the simulation of the electrical behaviour of LEDs and dc–dc converter systems by using software like Simulink. In addition, the proposed model can also be employed for the theoretical analysis and design of LED drivers. Experimental and simulation results are obtained proving the feasibility of the proposed model. Copyright © 2017 John Wiley & Sons, Ltd.
- 20 April 2017
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 45 (11) , 1760-1772
Simplified electrical modelling of power LEDs for DC–DC converter analysis and simulation
Summary: This paper presents a model of power light emitting diodes (LEDs) based on electrical variables and considering the concept of LED ‘equivalent resistance’, which has previously been used in discharge lamp modelling and is suitable to achieve fast simulations of LED converter systems. The model can be obtained with only some simple electrical measurements, thus making its implementation quite straightforward. The proposed model is oriented to the electronic engineering area, and it has special application for the simulation of the electrical behaviour of LEDs and dc–dc converter systems by using software like Simulink. In addition, the proposed model can also be employed for the theoretical analysis and design of LED drivers. Experimental and simulation results are obtained proving the feasibility of the proposed model. Copyright © 2017 John Wiley & Sons, Ltd.
- 16 January 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 32 (12) , 9179-9190
Analysis and Experiments on a Single-Inductor Half-Bridge LED Driver With Magnetic Control
This paper presents the analysis and experiments of a variable inductor (VI) based LED driver for dc grid lighting applications. The proposed driver requires only a series inductor and a transformer as major components to drive the LED lamp from a half-bridge inverter. By introducing a VI as the series inductor, the LED current can be controlled independently from any other parameter, which makes it possible to drive and regulate several LED branches from the same half-bridge output. Other advantages of the proposed converter include inherent open-circuit and short-circuit protections, zero-voltage switching for the bridge transistor and zero-current switching for the output rectifier diodes, simple dynamics, possibility of analog and pulse width modulation dimming, constant switching frequency operation, and high efficiency. The converter is thoroughly analyzed and modeled for both steady-state and dynamic operation. As another novelty of this paper, the dynamic response of the VI has been studied and taken into account to obtain the complete transfer function of the VI-controlled system. In addition, some housekeeping issues that usually arise when dealing with VI, e.g., how to drive the VI bias winding, are solved in this work. Experimental results provided from a 50 W laboratory prototype demonstrate the correctness of the performed analysis and the good possibilities of the proposed converter.
- 16 January 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 32 (12) , 9179-9190
Analysis and Experiments on a Single-Inductor Half-Bridge LED Driver With Magnetic Control
This paper presents the analysis and experiments of a variable inductor (VI) based LED driver for dc grid lighting applications. The proposed driver requires only a series inductor and a transformer as major components to drive the LED lamp from a half-bridge inverter. By introducing a VI as the series inductor, the LED current can be controlled independently from any other parameter, which makes it possible to drive and regulate several LED branches from the same half-bridge output. Other advantages of the proposed converter include inherent open-circuit and short-circuit protections, zero-voltage switching for the bridge transistor and zero-current switching for the output rectifier diodes, simple dynamics, possibility of analog and pulse width modulation dimming, constant switching frequency operation, and high efficiency. The converter is thoroughly analyzed and modeled for both steady-state and dynamic operation. As another novelty of this paper, the dynamic response of the VI has been studied and taken into account to obtain the complete transfer function of the VI-controlled system. In addition, some housekeeping issues that usually arise when dealing with VI, e.g., how to drive the VI bias winding, are solved in this work. Experimental results provided from a 50 W laboratory prototype demonstrate the correctness of the performed analysis and the good possibilities of the proposed converter.
- 3 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Analysis and design of a novel variable-inductor-based LED driver for DC lighting grids
This paper presents a novel variable inductor (VI) based LED driver for DC grid lighting applications. The proposed driver requires only a series inductor and a transformer as major components to drive the LED lamp from a half-bridge inverter. By introducing a VI as the series inductor, the LED current can be controlled independently from any other parameter, which makes it possible to drive and regulate several LED branches from the same half-bridge output. Other advantages of the proposed converter include inherent open circuit and short circuit protections, ZVS for the bridge transistor and ZCS for the output rectifier diodes, simple dynamics, possibility of analog and PWM dimming, constant switching frequency operation and high efficiency. The converter is thoroughly analyzed and modelled for both steady-state and dynamic operation. As another novelty of this paper, the dynamic response of the VI has been studied and taken into account to obtain the complete transfer function of the VI-controlled system. In addition, some housekeeping issues that usually arise when dealing with VI, e.g. how to drive the VI bias winding, are solved in this work. Experimental results provided from a 50 W laboratory prototype demonstrate the correctness of the performed analysis and the good possibilities of the proposed converter.
- 3 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Analysis and design of a novel variable-inductor-based LED driver for DC lighting grids
This paper presents a novel variable inductor (VI) based LED driver for DC grid lighting applications. The proposed driver requires only a series inductor and a transformer as major components to drive the LED lamp from a half-bridge inverter. By introducing a VI as the series inductor, the LED current can be controlled independently from any other parameter, which makes it possible to drive and regulate several LED branches from the same half-bridge output. Other advantages of the proposed converter include inherent open circuit and short circuit protections, ZVS for the bridge transistor and ZCS for the output rectifier diodes, simple dynamics, possibility of analog and PWM dimming, constant switching frequency operation and high efficiency. The converter is thoroughly analyzed and modelled for both steady-state and dynamic operation. As another novelty of this paper, the dynamic response of the VI has been studied and taken into account to obtain the complete transfer function of the VI-controlled system. In addition, some housekeeping issues that usually arise when dealing with VI, e.g. how to drive the VI bias winding, are solved in this work. Experimental results provided from a 50 W laboratory prototype demonstrate the correctness of the performed analysis and the good possibilities of the proposed converter.
- 24 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 31 (11) , 7735-7746
A Systematic Approach to Modeling Complex Magnetic Devices Using SPICE: Application to Variable Inductors
In this paper, a methodology to develop SPICE-based models of complex magnetic devices is presented. The proposed methodology is based on a reluctance equivalent circuit, which allows the user to study both the magnetic and electric behavior of the structure under any operating conditions. The different elements required to implement the reluctance model, namely, constant reluctances, variable reluctances, and windings, are implemented using SPICE behavioral modeling. These elements can thus be used to build a complete model for any magnetic device. The modeling process is illustrated with a particular example for a variable inductor. Simulations and experimental results are presented and compared to evaluate the accuracy and usefulness of the proposed modeling procedure.
- 24 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 31 (11) , 7735-7746
A Systematic Approach to Modeling Complex Magnetic Devices Using SPICE: Application to Variable Inductors
In this paper, a methodology to develop SPICE-based models of complex magnetic devices is presented. The proposed methodology is based on a reluctance equivalent circuit, which allows the user to study both the magnetic and electric behavior of the structure under any operating conditions. The different elements required to implement the reluctance model, namely, constant reluctances, variable reluctances, and windings, are implemented using SPICE behavioral modeling. These elements can thus be used to build a complete model for any magnetic device. The modeling process is illustrated with a particular example for a variable inductor. Simulations and experimental results are presented and compared to evaluate the accuracy and usefulness of the proposed modeling procedure.
- 1 March 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 1115-1122
Modeling magnetic devices using SPICE: Application to variable inductors
In this paper a methodology to develop SPICE-based models of complex magnetic devices is presented. The proposed methodology is based on a reluctance equivalent circuit (REC), which allows the user to study both the magnetic and electric behavior of the structure under any operating conditions. The different elements required to implement the reluctance model, namely, constant reluctances, variable reluctances and windings, are implemented using SPICE behavioral modeling. These elements can thus be used to build a complete model for any magnetic device. The modeling process is illustrated with a particular example for a variable inductor. Simulations and experimental results are presented and compared to evaluate the accuracy and usefulness of the proposed modeling procedure.
- 1 March 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 1115-1122
Modeling magnetic devices using SPICE: Application to variable inductors
In this paper a methodology to develop SPICE-based models of complex magnetic devices is presented. The proposed methodology is based on a reluctance equivalent circuit (REC), which allows the user to study both the magnetic and electric behavior of the structure under any operating conditions. The different elements required to implement the reluctance model, namely, constant reluctances, variable reluctances and windings, are implemented using SPICE behavioral modeling. These elements can thus be used to build a complete model for any magnetic device. The modeling process is illustrated with a particular example for a variable inductor. Simulations and experimental results are presented and compared to evaluate the accuracy and usefulness of the proposed modeling procedure.
- 1 October 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
A review on switched capacitor converters with high power density for OLED lamp driving
This paper presents a review of high-power-density non-resonant and resonant switched-capacitor (SC) converters topologies for driving organic-lighting-emitting-diode (OLEDs) lamps. These converters are light, small and cheaper in comparison with the linear power supplies and conventional DC-DC converters owing to the avoidance of large magnetic components. Resonant SC (RSC) converters show high efficiency and low EMI noise because they employ a small resonant inductor, which is connected in series with a switched capacitor in order to resonate at a frequency higher than switching frequency, thus allowing them to attain zero-current-switching (ZCS). The bidirectional step-up RSC converter has been identified as one of the best candidates to be used as an OLED driver. Simulation and experimental results from a laboratory prototype designed to supply a 60V 25W OLED lamp from a dc 30 V voltage source are presented.
- 1 October 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
A review on switched capacitor converters with high power density for OLED lamp driving
This paper presents a review of high-power-density non-resonant and resonant switched-capacitor (SC) converters topologies for driving organic-lighting-emitting-diode (OLEDs) lamps. These converters are light, small and cheaper in comparison with the linear power supplies and conventional DC-DC converters owing to the avoidance of large magnetic components. Resonant SC (RSC) converters show high efficiency and low EMI noise because they employ a small resonant inductor, which is connected in series with a switched capacitor in order to resonate at a frequency higher than switching frequency, thus allowing them to attain zero-current-switching (ZCS). The bidirectional step-up RSC converter has been identified as one of the best candidates to be used as an OLED driver. Simulation and experimental results from a laboratory prototype designed to supply a 60V 25W OLED lamp from a dc 30 V voltage source are presented.
- 28 January 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 59 (4) , 1689-1697
Analysis and Design of the Integrated Double Buck–Boost Converter as a High-Power-Factor Driver for Power-LED Lamps
In this paper, an integrated double buck-boost (IDBB) converter is proposed as a high-power-factor offline power supply for power-LED lamps. The IDBB converter features just one controlled switch and two inductors and is able to supply a solid-state lamp from the mains, providing high power factor and good efficiency. In this paper, the IDBB converter is analyzed, and a design methodology is proposed. It is demonstrated that, with a careful design of the converter, the filter capacitances can be made small enough so that film capacitors may be used. In this way, the converter mean time between failures can be made as high as that of the solid-state lamp. A design example for a 70-W converter supplied from a 230 V/50 Hz mains for street lighting applications is shown. Finally, experimental results from a laboratory prototype are also presented.
- 28 January 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 59 (4) , 1689-1697
Analysis and Design of the Integrated Double Buck–Boost Converter as a High-Power-Factor Driver for Power-LED Lamps
In this paper, an integrated double buck-boost (IDBB) converter is proposed as a high-power-factor offline power supply for power-LED lamps. The IDBB converter features just one controlled switch and two inductors and is able to supply a solid-state lamp from the mains, providing high power factor and good efficiency. In this paper, the IDBB converter is analyzed, and a design methodology is proposed. It is demonstrated that, with a careful design of the converter, the filter capacitances can be made small enough so that film capacitors may be used. In this way, the converter mean time between failures can be made as high as that of the solid-state lamp. A design example for a 70-W converter supplied from a 230 V/50 Hz mains for street lighting applications is shown. Finally, experimental results from a laboratory prototype are also presented.
- 1 November 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 25 (1553572X) , 2541-2546
Analysis and design of the quadratic buck-boost converter as a high-power-factor driver for power-LED lamps
In this paper the quadratic buck-boost (QBB) converter is proposed as a high-power-factor off-line power supply for power-LED lamps. The QBB converter features just one controlled switch and two inductors and is able to supply a solid-state lamp from the mains providing high power factor and good efficiency. In the paper, the QBB converter is analyzed and a design methodology is proposed. It is demonstrated that with a careful design of the converter, the filter capacitances can be made small enough so that film capacitors may be used. In this way, the converter mean time between failures (MTBF) can be made as high as that of the solid-state lamp. A design example for a 70 W converter supplied from a 230 V/50 Hz mains for street lighting applications is shown. Finally, experimental results from a laboratory prototype are also presented.
- 1 November 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 25 (1553572X) , 2541-2546
Analysis and design of the quadratic buck-boost converter as a high-power-factor driver for power-LED lamps
In this paper the quadratic buck-boost (QBB) converter is proposed as a high-power-factor off-line power supply for power-LED lamps. The QBB converter features just one controlled switch and two inductors and is able to supply a solid-state lamp from the mains providing high power factor and good efficiency. In the paper, the QBB converter is analyzed and a design methodology is proposed. It is demonstrated that with a careful design of the converter, the filter capacitances can be made small enough so that film capacitors may be used. In this way, the converter mean time between failures (MTBF) can be made as high as that of the solid-state lamp. A design example for a 70 W converter supplied from a 230 V/50 Hz mains for street lighting applications is shown. Finally, experimental results from a laboratory prototype are also presented.