PRPolphat Ruamcharoen

Polphat Ruamcharoen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Polphat Ruamcharoen has a total of 30 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Advancing modified epoxy asphalts from derived waste PET: effects of base asphalt types on fuel resistance joint sealant performance

    by Panisa Sangnak, Chor. Wayakron Phetphaisit, Saranagon Hemavibool, Polphat Ruamcharoen

    In road construction, asphalt is favoured as a pavement material. Beyond this application, asphalt is also widely used as a joint sealer, filling gaps between cracked surfaces and between concrete ...

  • Open Access

    Acoustical and Mechanical Properties of Foam Concrete Incorporating Bottom Ash Filler Derived from Oil Palm Biomass

    by Kritsadi Thetpraphi, Sarawut Chulok, Nawarat Seetapong, Nasreen Dortha, Polphat Ruamcharoen, Purintorn Chanlert

    This study investigates the sound absorption performance and mechanical behavior of foam concrete incorporating oil palm bottom ash (OPBA) as a partial cement replacement at levels of 0–40% by mass, with specimens water-cured for 7, 14, and 28 days. Acoustically, OPBA content produces a pronounced U-shaped dependence of the noise reduction coefficient (NRC) on replacement level: a trough at 10% BA (NRC ≈ 0.16–0.23) is flanked by elevated absorption at 0% BA and, most notably, at 40% BA / 28 days, where peak NRC ≈ 0.38 is achieved across the 200–5000 Hz measurement range at 40 mm specimen thickness. Statistical analysis confirmed OPBA content as the primary governing factor for both acoustic and mechanical responses, with curing duration playing a secondary role. Among mechanical properties, compressive strength peaked at 20% BA / 7 days (≈ 2.44 MPa) and tangent modulus at 10% BA / 7 days (≈ 109.75 MPa), with both declining steeply beyond 20% BA. A counter-intuitive finding is that prolonged water soaking reduced rather than enhanced mechanical performance, attributed to calcium ion leaching and potassium salt dissolution within the highly porous matrix. OPBA was characterized as silica-rich, dominated by crystalline quartz and cristobalite, with a bimodal particle size distribution (D₁₀ = 2.5 μm, D₅₀ = 15.4 μm, D₉₀ = 999.4 μm) that governs its dual filler-reinforcement and pore-enlargement roles at low and high replacement levels, respectively. These results indicate that 40% OPBA / 28 days is optimal for non-structural acoustic panel applications, while BA content should not exceed 20% where structural performance is required, offering a practical route for valorizing oil palm agricultural residue in sustainable building materials.

  • Sago Starch Reinforced With Cellulose Microfibers Isolated From Dialium cochinchinense Residue

    by Polphat Ruamcharoen, Purintorn Chanlert, Chumphon Numuang, Lapporn Vayachuta, Jareerat Ruamcharoen

    This research investigated the development of sago starch (SS) film reinforced with velvet tamarind ( Dialium cochinchinense ) peels for potential biopolymer film applications. SS was gelled at 80°C and plasticized with glycerol. After that, VT and treated VT (TVT) fibers were incorporated with content of 1, 3, and 5 wt%. The SS, SS_VT, and SS_TVT biocomposites were systematically evaluated for their transparency, water resistance and tensile properties. The addition of VT and TVT significantly improved ultraviolet (UV) protection, although this improvement was accompanied by a decrease in visible light transparency. Water absorption and water vapor transmission of the biocomposite films also decreased compared to neat SS. Moreover, the biocomposite films exhibited substantially higher tensile strength (TS) and Young's modulus (YM) than neat SS film. Notably, the composite film containing 3 wt% VT demonstrated the highest TS and YM value. This confirmed the effective dispersion of 3 wt% of VT within starch matrix and strong interface interaction between cellulose fibers and starch, as revealed by FTIR and SEM analysis. The thermal degradation temperatures of biocomposite films containing 1 wt% VT and TVT were shifted to higher values compared to that of the starch matrix. The incorporation of VT and TVT enhanced the tensile properties of the biocomposite films; however, TVT‐reinforced films showed relatively inferior performance compared to VT reinforced films, primarily due to increased particle agglomeration, as observed by SEM. Totally, SS films reinforced with VT show strong potential for biopolymer packaging applications, owing to their improved water resistance and mechanical properties.

  • Sago starch and esterified sago starch as eco-friendly fillers for rigid polyurethane foams

    by Jareerat Ruamcharoen, Chor Wayakron Phetphaisit, Purintorn Chanlert, Sameela Cheming, Polphat Ruamcharoen

    Novel fillers from sago starch and esterified sago starch were employed as natural fillers for rigid polyurethane foams (RPUFs). Sago starch was esterified by maleic anhydride, resulting in the presence of ester groups on the starch structure. Filled RPUFs were prepared with 0.5-7.0 wt% of starch fillers in the polyol component. The influence of filler type and content on the cell morphology and properties of the RPUFs was analyzed. The results revealed that the esterified sago starch showed better compatibility with polyurethane matrix than the sago starch, which in turn impacted the cellular morphology and physico-mechanical properties of the resulting RPUFs. The density and compressive strength of the RPUFs filled with esterified sago starch were higher than those filled with unmodified sago starch, while their water absorption, and volume shrinkage were lower. The findings also suggested that the compressive strength and density of filled RPUFs increased with starch filler content up to the optimal point and then decreased. This was due to the impact of filler content on cell size, with smaller cell size at low filler content leading to increased strength and density, whereas larger cell size and more open cells at higher filler content reducing strength and density. The best properties were obtained with 1.0 wt% of unmodified sago starch and 0.5 wt% of esterified sago starch in the polyol component.


  • Open Access

    Prototype System for Production of Refuse Derived Fuel (RDF-5) from Municipal Solid Waste Using Natural Rubber as Binder

    by Kiattisak Rattanadilok Na Phuket, Tussanee Srimachai, Chaiyoot Meengam, Polphat Ruamcharoen

    The development of RDF-5 fuel from community waste using natural rubber as a binder was investigated. The results showed that the calorific and heat values were increased proportionately to the amount of rubber added. The ratio with the highest calorific value was 50:50, followed by 75:25, 90:10, and 95:5. The calorific value was 40.67 MJ/kg (9720 kcal/kg), 40.24 MJ/kg (9,617 kcal/kg), 39.28 (9,389 kcal/kg) and 39.18 MJ/kg (9,365 kcal/kg), respectively. Compared with 100:0, have a calorific value of 38.84 MJ/kg (9,284 kcal/kg). The experimental addition of natural rubber as a binder makes the combustion process more complete, resulting in faster fuel ignition time or easier igniting, less ash content, and being environmentally friendly. The research team chose to develop the ratio of 95:5 because the economic analysis showed a fast payback period of only 5.72 years. So, the ratio of 95:5 is the optimal condition that can scale up to the industrial level. The production cost of RDF-5 is 1,935 baht/ton for 50 baht/kg of natural rubber. The amount of emission caused by the combustion process of RDF-5 (95:5) passed the standard. Therefore, the evaluation of this research found that RDF-5 fuels from community waste using natural rubber as a binder. It is one of the attractive alternatives to renewable fuel generation and solid waste management solutions and helps improve the environmental quality of communities.


  • Green rigid polyurethane foam from hydroxyl liquid natural rubbers as macro-hydroxyl polyols

    by Jareerat Ruamcharoen, Chor Wayakron Phetphaisit, Polphat Ruamcharoen

    The novel renewable source precursors from hydroxyl liquid natural rubbers (HLNRs) with various secondary hydroxyl content of 22% (HLNR22), 35% (HLNR35), and 50% (HLNR50) (or naming macro-hydroxyl polyols) were used to prepare rigid polyurethane foam. The aim of this study was to investigate the effect of hydroxyl content of HLNR precursors and the ratio of HLNRs and commercial polyols on physico-mechanical properties of rigid polyurethane foams in comparison to foams made from commercial polyols. The increase in hydroxyl content of HLNRs resulted in the foams with larger cell size while the increase in the HLNR portion caused a small and more uniform cell size, which is related to their density and compressive strength. Thermal stability of polyurethane foams was analyzed by thermogravimetric analysis and the results have demonstrated that the use of HLNR polyols improved thermal stability of polyurethane foams in comparison to commercial foam.


  • The effect of percent hydrogenation and vulcanization system on ozone stability of hydrogenated natural rubber vulcanizates using Raman spectroscopy

    by Korn Taksapattanakul, Tulyapong Tulyapitak, Pranee Phinyocheep, Polphat Ruamcharoen, Jareerat Ruamcharoen, Fabienne Lagarde, Philippe Daniel


  • Raman investigation of thermoplastic vulcanizates based on hydrogenated natural rubber/polypropylene blends

    by Korn Taksapattanakul, Tulyapong Tulyapitak, Pranee Phinyocheep, Polphat Ruamcharoen, Jareerat Ruamcharoen, Fabienne Lagarde, Mathieu Edely, Philippe Daniel


  • Mathematical Modelling of Urea-Formaldehyde Polymerization Kinetics Using Mechanism Approach

    by Polphat Ruamcharoen, Jareerat Ruamcharoen

    Nowadays, formaldehyde is considered to be a hazardous volatile chemical. One of the formaldehyde sources is urea-formaldehyde resin which is mainly used as an adhesive in particleboard production. Hence, it is necessary to minimize the formaldehyde residue from urea-formaldehyde synthesis. This present work involves the kinetic modelling of urea-formaldehyde polymerization to predict formaldehyde concentration during the pre-polymerization process. On the basis of previous proposed mechanism, the kinetic model which accounted for the number of the functional groups on urea and formaldehyde and also reactive polymer chains was developed as a set of ordinary differential equations (ODEs). The formaldehyde concentrations from computer simulation results were compared with those from experimental investigation. Good agreement between simulation and experimental results was obtained. The developed kinetic model can be also applied to predict the functional group evolution during polymerization. This helps producers select the condition for production to minimize formaldehyde residue and predict the chemical structure of final product.