Tara Benkel
Tara Benkel has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Francesco Grilli
Karlsruhe Institute of Technology
4 shared publications - Arnaud Badel
CNRS Grenoble INP G2ELab Institut Néel Université Grenoble Alpes Grenoble France
3 shared publications - Xavier Chaud
LNCMI-EMFL-CNRS, INSA, Universit Grenoble Alpes, Grenoble, France
3 shared publications - Enric Pardo
Institute of Electrical Engineering Slovak Academy of Sciences Bratislava Slovakia
2 shared publications - Fabian Schreiner
Institute for Technical Physics, Karlsruhe Institute of Technology Electrical Engineering and Information Technology, 226220 Karlsruhe, Baden-Wurttemberg Germany 76131
2 shared publications - Frédéric Sirois
Polytechnique Montral, Montreal, QC, Canada
2 shared publications
Latest Publications
- 25 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Modelling of a Large-Scale Non-Insulated Non-Planar HTS Stellarator Coil Using Quanscient Allsolve
Stellarators present features such as steady-state operation and intrinsic stability that make them more attractive than tokamaks in their scaling to fusion power plants. By leveraging more possible configurations, stellarators can be optimized for better engineering feasibility, e.g., resilience to manufacturing tolerances, reduced mechanical load on conductor, material optimization, cost of fabrication. Finite Element Analyses are crucial for the design and optimization of High-Temperature Superconducting (HTS) REBCO non-planar coils. However, accurate simulation of large-scale magnetostatic, mechanical, and quench models can take days or even weeks to compute. In this work, we present a model of a real-size, HTS, non-insulated, non-planar stellarator coil and perform in Quanscient Allsolve®, a transient simulation study including modelling quench, using the $H - \varphi $ formulation. It is shown that transient model benefits heavily from the built-in Domain Decomposition Method (DDM), which allows reaching reasonable computation times. Such models become then invaluable in predicting and understanding the complex behavior of non-insulated large-scale REBCO magnets, including their intrinsic energy imbalance.
- 25 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Modelling of a Large-Scale Non-Insulated Non-Planar HTS Stellarator Coil Using Quanscient Allsolve
Stellarators present features such as steady-state operation and intrinsic stability that make them more attractive than tokamaks in their scaling to fusion power plants. By leveraging more possible configurations, stellarators can be optimized for better engineering feasibility, e.g., resilience to manufacturing tolerances, reduced mechanical load on conductor, material optimization, cost of fabrication. Finite Element Analyses are crucial for the design and optimization of High-Temperature Superconducting (HTS) REBCO non-planar coils. However, accurate simulation of large-scale magnetostatic, mechanical, and quench models can take days or even weeks to compute. In this work, we present a model of a real-size, HTS, non-insulated, non-planar stellarator coil and perform in Quanscient Allsolve®, a transient simulation study including modelling quench, using the $H - \varphi $ formulation. It is shown that transient model benefits heavily from the built-in Domain Decomposition Method (DDM), which allows reaching reasonable computation times. Such models become then invaluable in predicting and understanding the complex behavior of non-insulated large-scale REBCO magnets, including their intrinsic energy imbalance.
- 5 November 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (12) , 125006
Electromagnetic-thermal modeling of high-temperature superconducting coils with homogenized method and different formulations: a benchmark
High-temperature superconducting coils are used in various large-scale applications, like rotating machines and high-field magnets. However, modeling these coils is a complicated and time-consuming process, especially due to the non-linearity of the current–voltage characteristics of the superconductors and the complex multiphysics involved. In this work, we used a fast homogenized method to model the coupled electromagnetic and electrothermal properties of racetrack and pancake coils for different applications. For this purpose, various formulations wielding homogenization methods are used and benchmarked with each other, as well as with models considering the detailed structure of the HTS tapes. We observe a very good agreement between different models (homogenized and detailed), and we discuss the pros and cons of the inclusion of insulating layers between the turns in homogenization. This work was performed under the collaboration of the COST action modeling teams and can be used as a review of the state-of-the-art superconductor modeling techniques, and a source for the development and benchmark of future numerical methods.
- 5 November 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (12) , 125006
Electromagnetic-thermal modeling of high-temperature superconducting coils with homogenized method and different formulations: a benchmark
High-temperature superconducting coils are used in various large-scale applications, like rotating machines and high-field magnets. However, modeling these coils is a complicated and time-consuming process, especially due to the non-linearity of the current–voltage characteristics of the superconductors and the complex multiphysics involved. In this work, we used a fast homogenized method to model the coupled electromagnetic and electrothermal properties of racetrack and pancake coils for different applications. For this purpose, various formulations wielding homogenization methods are used and benchmarked with each other, as well as with models considering the detailed structure of the HTS tapes. We observe a very good agreement between different models (homogenized and detailed), and we discuss the pros and cons of the inclusion of insulating layers between the turns in homogenization. This work was performed under the collaboration of the COST action modeling teams and can be used as a review of the state-of-the-art superconductor modeling techniques, and a source for the development and benchmark of future numerical methods.
- 23 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (6) , 1-7
T–A-Formulation to Model Electrical Machines With HTS Coated Conductor Coils
- 23 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (6) , 1-7
T–A-Formulation to Model Electrical Machines With HTS Coated Conductor Coils
- Open Access
- 20 January 2020
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 33 (3) , 035006
Fluorescent thermal imaging of a quench in insulated and non-insulated REBCO-wound pancake coils following a heater pulse at 77 K
High temperature superconductors (HTS)-wound coils are being developed for use in motors, generators as well as magnet applications. Determining the stability and safe operating margins of such coils still poses challenges. While the recently introduced no-insulation winding method provides a remedy for many problems, it comes with its own limitations. For comparison, we have wound two pancake coils from HTS coated conductors with the insulated and non-insulated winding techniques. Both coils were coated with a fluorescent, temperature-sensitive coating, which allowed monitoring the surface temperatures during operation. The coils were cooled to 77 K via a combination of conduction and gas cooling, and their electrical and thermal behaviour was observed in operation. Here we present the normal transition of both coils caused by an artificially introduced instability due to a surface-mounted, resistive heater element. In the insulated coil, the localized disturbance caused a local transition of the superconductor to the normal conducting state, triggering a thermal runaway. Merely the turns in contact with the artificial disturbance heated up, while the rest of the coil remained in the superconducting state. In the non-insulated coil—although a much longer heater pulse was required—the normal transition started from the weakest point of the coil (around the bobbin) and the whole coil was heating thereafter, with the centre heating more.
- 20 January 2020
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 33 (3) , 035006
Open AccessFluorescent thermal imaging of a quench in insulated and non-insulated REBCO-wound pancake coils following a heater pulse at 77 K
High temperature superconductors (HTS)-wound coils are being developed for use in motors, generators as well as magnet applications. Determining the stability and safe operating margins of such coils still poses challenges. While the recently introduced no-insulation winding method provides a remedy for many problems, it comes with its own limitations. For comparison, we have wound two pancake coils from HTS coated conductors with the insulated and non-insulated winding techniques. Both coils were coated with a fluorescent, temperature-sensitive coating, which allowed monitoring the surface temperatures during operation. The coils were cooled to 77 K via a combination of conduction and gas cooling, and their electrical and thermal behaviour was observed in operation. Here we present the normal transition of both coils caused by an artificially introduced instability due to a surface-mounted, resistive heater element. In the insulated coil, the localized disturbance caused a local transition of the superconductor to the normal conducting state, triggering a thermal runaway. Merely the turns in contact with the artificial disturbance heated up, while the rest of the coil remained in the superconducting state. In the non-insulated coil—although a much longer heater pulse was required—the normal transition started from the weakest point of the coil (around the bobbin) and the whole coil was heating thereafter, with the centre heating more.
- Open Access
- 22 August 2019
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 32 (10) , 105006
Fluorescent thermal imaging of a non-insulated pancake coil wound from high temperature superconductor tape
We have wound a 157-turn, non-insulated pancake coil with an outer diameter of 85 mm and we cooled it down to 77 K with a combination of conduction and gas cooling. Using high-speed fluorescent thermal imaging in combination with electrical measurements we have investigated the coil under load, including various ramping tests and over-current experiments. We have found that the coil does not heat up measurably when being ramped to below its critical current. Two over-current experiments are presented, where in one case the coil recovered by itself and in another case a thermal runaway occurred. We have recorded heating in the bulk of the windings due to local defects, however the coil remained cryostable even during some over-critical conditions and heated only to about 82–85 K at certain positions. A thermal runaway was observed at the center, where the highest magnetic field and a resistive joint create a natural defect. The maximum temperature, ∼100 K, was reached only in the few innermost windings around the coil former.
- 22 August 2019
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 32 (10) , 105006
Open AccessFluorescent thermal imaging of a non-insulated pancake coil wound from high temperature superconductor tape
We have wound a 157-turn, non-insulated pancake coil with an outer diameter of 85 mm and we cooled it down to 77 K with a combination of conduction and gas cooling. Using high-speed fluorescent thermal imaging in combination with electrical measurements we have investigated the coil under load, including various ramping tests and over-current experiments. We have found that the coil does not heat up measurably when being ramped to below its critical current. Two over-current experiments are presented, where in one case the coil recovered by itself and in another case a thermal runaway occurred. We have recorded heating in the bulk of the windings due to local defects, however the coil remained cryostable even during some over-critical conditions and heated only to about 82–85 K at certain positions. A thermal runaway was observed at the center, where the highest magnetic field and a resistive joint create a natural defect. The maximum temperature, ∼100 K, was reached only in the few innermost windings around the coil former.
- 1 December 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 28 (3) , 1-5
Characterization of HTS Insulated Coil for High Field Insert up to 19 T
High Temperature Superconductors (HTS) are a strong candidate for high field magnets. As their properties are extraordinary especially under high fields and very low temperatures, there are many ongoing projects around the world. The NOUGAT project aims at building a 10 T insert operating inside a 20 T resistive background. Its objectives are not to reach higher field than the already existing resistive magnets but rather to overcome the main issues of using HTS above 20 T and pave the way toward full superconductive magnets at lower cost. REBCO coated conductor tape was preferred for the NOUGAT insert even if its implementation is still challenging. Both insulated and metal insulated (MI) coils have been considered for the NOUGAT project. Due to their self-protection behavior, MI windings have been selected for building the insert but we are still investigating insulated coils for future applications. We built a fully-instrumented insulated single pancake wound with a 6-mm wide tape. Voltage taps are set up on each turn to monitor the quench propagation in vapor helium up to 60 K under high magnetic field up to 19 T. This study aims at developing our understanding of the windings quench behavior and testing various quench detection procedures for future large scale insulated applications.
- 1 December 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 28 (3) , 1-5
Characterization of HTS Insulated Coil for High Field Insert up to 19 T
High Temperature Superconductors (HTS) are a strong candidate for high field magnets. As their properties are extraordinary especially under high fields and very low temperatures, there are many ongoing projects around the world. The NOUGAT project aims at building a 10 T insert operating inside a 20 T resistive background. Its objectives are not to reach higher field than the already existing resistive magnets but rather to overcome the main issues of using HTS above 20 T and pave the way toward full superconductive magnets at lower cost. REBCO coated conductor tape was preferred for the NOUGAT insert even if its implementation is still challenging. Both insulated and metal insulated (MI) coils have been considered for the NOUGAT project. Due to their self-protection behavior, MI windings have been selected for building the insert but we are still investigating insulated coils for future applications. We built a fully-instrumented insulated single pancake wound with a 6-mm wide tape. Voltage taps are set up on each turn to monitor the quench propagation in vapor helium up to 60 K under high magnetic field up to 19 T. This study aims at developing our understanding of the windings quench behavior and testing various quench detection procedures for future large scale insulated applications.
- 2 August 2017
- Published by EDP Sciences in The European Physical Journal Applied Physics
- Vol. 79 (3) , 30601
REBCO tape performance under high magnetic field
New improvements in high temperature superconductors (HTS) make them a promising candidate for building the next generation of high field magnets. As the conductors became recently available in long length, new projects such as NOUGAT (new magnet generation to generate Tesla at low cost) were started. This project aims at designing and building an HTS magnet prototype generating 10 T inside a 20 T resistive magnet. In this configuration, severe mechanical stress is applied on the insert and its extremities are subject to a high transverse component of the field. Because the conductor has anisotropic properties, it has to be studied carefully under similar conditions as the final prototype. First, this paper presents both the NOUGAT project and its context. Then, it shows the experimental results on short HTS tapes studied under high magnetic field up to 23 T with varying orientation. These results allow validating the current margin of the prototype. Finally, a first wound prototype is presented with experimental results up to 200 A under 16 T.
- 2 August 2017
- Published by EDP Sciences in The European Physical Journal Applied Physics
- Vol. 79 (3) , 30601
REBCO tape performance under high magnetic field
New improvements in high temperature superconductors (HTS) make them a promising candidate for building the next generation of high field magnets. As the conductors became recently available in long length, new projects such as NOUGAT (new magnet generation to generate Tesla at low cost) were started. This project aims at designing and building an HTS magnet prototype generating 10 T inside a 20 T resistive magnet. In this configuration, severe mechanical stress is applied on the insert and its extremities are subject to a high transverse component of the field. Because the conductor has anisotropic properties, it has to be studied carefully under similar conditions as the final prototype. First, this paper presents both the NOUGAT project and its context. Then, it shows the experimental results on short HTS tapes studied under high magnetic field up to 23 T with varying orientation. These results allow validating the current margin of the prototype. Finally, a first wound prototype is presented with experimental results up to 200 A under 16 T.
- 18 January 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 27 (4) , 1-5
Preliminary Tests and Margin Estimate for a REBCO Insulated 10 T Insert Under High Magnetic Field
Our project is to build a high-temperature superconductor (HTS) insert generating 10 T in its center and expected to work inside a 20 T background field. In the first step, the background field is provided by a resistive magnet to avoid major coupling issues. Nevertheless, the final goal is to have the insert operating inside an LTS magnet to yield a 30 T-class all-superconducting magnet. The insert is designed as a stack of pancakes and double pancakes wound with REBCO tapes. Preliminary tests are performed on a deposited polyimide insulated coil, although design has started with metallic-insulation coils. This paper presents results obtained on a double pancake insulated HTS coil that was tested inside both a resistive coil at LNCMI and a superconducting magnet at Tohoku University. The electrical and mechanical behaviors of the sample coil are discussed, and margins are estimated taking into account the field distribution on each point of the coil. Results are encouraging as the coil passes 370 A (82.9% lc) self-field and 260 A (68.6% lc) under 8 T. Moreover, the coil is still working even after the outer magnet quench.
- 18 January 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 27 (4) , 1-5
Preliminary Tests and Margin Estimate for a REBCO Insulated 10 T Insert Under High Magnetic Field
Our project is to build a high-temperature superconductor (HTS) insert generating 10 T in its center and expected to work inside a 20 T background field. In the first step, the background field is provided by a resistive magnet to avoid major coupling issues. Nevertheless, the final goal is to have the insert operating inside an LTS magnet to yield a 30 T-class all-superconducting magnet. The insert is designed as a stack of pancakes and double pancakes wound with REBCO tapes. Preliminary tests are performed on a deposited polyimide insulated coil, although design has started with metallic-insulation coils. This paper presents results obtained on a double pancake insulated HTS coil that was tested inside both a resistive coil at LNCMI and a superconducting magnet at Tohoku University. The electrical and mechanical behaviors of the sample coil are discussed, and margins are estimated taking into account the field distribution on each point of the coil. Results are encouraging as the coil passes 370 A (82.9% lc) self-field and 260 A (68.6% lc) under 8 T. Moreover, the coil is still working even after the outer magnet quench.