Andrew Brennan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Andrew Brennan has a total of 81 co-authors. Here are the top co-authors by number of shared publications:
- Michael John Brown
School of Science and Engineering, University of Dundee, Dundee, UK
16 shared publications - Santana Phani Gopal Madabhushi
Univ. of Cambridge
12 shared publications - William Michael Coombs
Department of Engineering, Durham University, Durham, UK
11 shared publications - Scott Robinson
University of Dundee § School of Science and Engineering Dundee
7 shared publications - Charles Edward Augarde
Department of Engineering, Durham University, Durham, UK
6 shared publications - Jonathan Adam Knappett
Department of Engineering Science, University of Oxford, (formerly University of Dundee), Oxford, UK
6 shared publications
Latest Publications
- Open Access
- 22 October 2025
- Published by Springer Nature in Acta Geotechnica
- Vol. 21 (3) , 1265-1279
The variation of large strain viscous rate effects from undrained triaxial element testing of Kaolin clay
Viscous (undrained) rate effects lead to an increase in the shear strength of fine-grained soils such as clays when sheared at high strain rates. Correct rate effect parameters are key to accurate predictions of behaviour in a range of geotechnical applications, from subsea cable ploughing and rapid load testing of piles through to numerical modelling of offshore foundation systems. The factors influencing the magnitude of rate effects are, however, still poorly understood. Through a series of 100-mm diameter high-speed undrained triaxial tests (strain rates ranging from 300 to 180,000%/hr and initial effective stresses from 300 to 1350 kPa) on Kaolin clay, this paper investigates the influence of the soil state and stress history on rate effects across a wide strain range. Viscous rate effects ranging from 10 to 16% per log cycle are observed, and the liquidity index is observed to correlate to the magnitude of the rate effects. Viscous rate effects are also shown to reduce with increasing strain level, and a model is proposed which allows the rate effect in Kaolin to be predicted accounting for both of these factors. This model is potentially useful in analytical and numerical studies.
- 22 October 2025
- Published by Springer Nature in Acta Geotechnica
- Vol. 21 (3) , 1265-1279
Open AccessThe variation of large strain viscous rate effects from undrained triaxial element testing of Kaolin clay
Viscous (undrained) rate effects lead to an increase in the shear strength of fine-grained soils such as clays when sheared at high strain rates. Correct rate effect parameters are key to accurate predictions of behaviour in a range of geotechnical applications, from subsea cable ploughing and rapid load testing of piles through to numerical modelling of offshore foundation systems. The factors influencing the magnitude of rate effects are, however, still poorly understood. Through a series of 100-mm diameter high-speed undrained triaxial tests (strain rates ranging from 300 to 180,000%/hr and initial effective stresses from 300 to 1350 kPa) on Kaolin clay, this paper investigates the influence of the soil state and stress history on rate effects across a wide strain range. Viscous rate effects ranging from 10 to 16% per log cycle are observed, and the liquidity index is observed to correlate to the magnitude of the rate effects. Viscous rate effects are also shown to reduce with increasing strain level, and a model is proposed which allows the rate effect in Kaolin to be predicted accounting for both of these factors. This model is potentially useful in analytical and numerical studies.
- 1 March 2023
- Published by Emerald Publishing in Géotechnique Letters
- Vol. 13 (1) , 48-53
Impacts of reference strain rate and strain level dependency on rate effects in fine-grained soils
Viscous rate effects in fine-grained soils may occur in many engineering applications (e.g. dynamically penetrated anchors, sampling, rapid load testing of piles or high-speed soil characterisation), where high strain rates are induced during shear. Often it is difficult to correct for this enhancement of soil strength as fundamental understanding and quantification of rate effects is an area where further research is required. This is at least in part due to limitations of soil characterisation equipment and instrumentation. With the aim of tackling some of these issues a high-speed triaxial testing system was developed incorporating lubricated end platens, which was used to test kaolin at strain rates from 0·1 to 180 000%/h. This allowed observation of behaviour from fully drained, partially drained and undrained conditions, through to viscous effects. Results were used to investigate how rate effects are influenced by strain and consolidation level and how rate normalisation parameters are affected. This was then used to improve a commonly adopted rate characterisation approach such that it performed better across a wider range of strain rates and can be used for more consistent evaluation of rate effects between studies.
- 1 March 2023
- Published by Emerald Publishing in Géotechnique Letters
- Vol. 13 (1) , 48-53
Impacts of reference strain rate and strain level dependency on rate effects in fine-grained soils
Viscous rate effects in fine-grained soils may occur in many engineering applications (e.g. dynamically penetrated anchors, sampling, rapid load testing of piles or high-speed soil characterisation), where high strain rates are induced during shear. Often it is difficult to correct for this enhancement of soil strength as fundamental understanding and quantification of rate effects is an area where further research is required. This is at least in part due to limitations of soil characterisation equipment and instrumentation. With the aim of tackling some of these issues a high-speed triaxial testing system was developed incorporating lubricated end platens, which was used to test kaolin at strain rates from 0·1 to 180 000%/h. This allowed observation of behaviour from fully drained, partially drained and undrained conditions, through to viscous effects. Results were used to investigate how rate effects are influenced by strain and consolidation level and how rate normalisation parameters are affected. This was then used to improve a commonly adopted rate characterisation approach such that it performed better across a wider range of strain rates and can be used for more consistent evaluation of rate effects between studies.
- 1 February 2022
- Published by Emerald Publishing in Géotechnique
- Vol. 72 (2) , 108-126
Physical modelling to demonstrate the feasibility of screw piles for offshore jacket-supported wind energy structures
Screw piles potentially offer quieter installation and enhanced axial tensile capacity over straight-shafted driven piles. As such, they have been suggested as a possible foundation solution for offshore jacket-supported wind turbines in deeper water. To investigate the feasibility of their use in this setting, centrifuge testing of six model screw piles of different designs was conducted to measure the installation requirements and ultimate axial capacity of the piles in very dense and medium-dense sand. The screw piles were designed to sustain loads generated by an extreme design scenario using published axial capacity and torque prediction formulae. Single- and double-helix designs, including an optimised design, intended to minimise installation requirements, with reduced geometry were installed and tested in-flight. Piles in the medium-dense sand, for example, had significant installation requirements of up to 18·4 MNm (torque) and 28·8 MN (vertical force), which were accurately predicted using correlations with cone resistance data (cone penetration test). Existing axial capacity design methods did not perform well for these large-scale screw piles, overestimating compressive and tensile capacities. Revised analytical methods for installation and axial capacity estimates are proposed here based on the centrifuge test results.
- 1 February 2022
- Published by Emerald Publishing in Géotechnique
- Vol. 72 (2) , 108-126
Physical modelling to demonstrate the feasibility of screw piles for offshore jacket-supported wind energy structures
Screw piles potentially offer quieter installation and enhanced axial tensile capacity over straight-shafted driven piles. As such, they have been suggested as a possible foundation solution for offshore jacket-supported wind turbines in deeper water. To investigate the feasibility of their use in this setting, centrifuge testing of six model screw piles of different designs was conducted to measure the installation requirements and ultimate axial capacity of the piles in very dense and medium-dense sand. The screw piles were designed to sustain loads generated by an extreme design scenario using published axial capacity and torque prediction formulae. Single- and double-helix designs, including an optimised design, intended to minimise installation requirements, with reduced geometry were installed and tested in-flight. Piles in the medium-dense sand, for example, had significant installation requirements of up to 18·4 MNm (torque) and 28·8 MN (vertical force), which were accurately predicted using correlations with cone resistance data (cone penetration test). Existing axial capacity design methods did not perform well for these large-scale screw piles, overestimating compressive and tensile capacities. Revised analytical methods for installation and axial capacity estimates are proposed here based on the centrifuge test results.
- 1 October 2021
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 58 (10) , 1466-1477
A cone penetration test (CPT) approach to cable plough performance prediction based upon centrifuge model testing
Cable ploughing is an important technique for burying and protecting offshore cables. The ability to predict the required tow force and plough performance is essential to allow vessel selection and project programming. Existing tow force models require calibration against full-scale field testing to determine empirical parameters, a requirement that may hinder their use. In this study the factors controlling the plough resistance were investigated using a series of dry and saturated 1/50th scale model cable plough tests in sand in a geotechnical centrifuge at 50g at a range of target trench depths, sand relative densities, and plough velocities. An improved model for predicting cable plough tow force that separates out the key components of resistance and allows tow force prediction without the use of field-derived empirical coefficients is presented. It is demonstrated that the key parameters in this model can be easily determined from in situ cone penetration tests (CPTs), allowing it to be used offshore where site investigation techniques may be more limited compared to onshore locations. The model is validated against the centrifuge cable plough tests, demonstrating it can correctly predict both the static (dry) and rate effect (saturated) tow forces.
- 1 October 2021
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 58 (10) , 1466-1477
A cone penetration test (CPT) approach to cable plough performance prediction based upon centrifuge model testing
Cable ploughing is an important technique for burying and protecting offshore cables. The ability to predict the required tow force and plough performance is essential to allow vessel selection and project programming. Existing tow force models require calibration against full-scale field testing to determine empirical parameters, a requirement that may hinder their use. In this study the factors controlling the plough resistance were investigated using a series of dry and saturated 1/50th scale model cable plough tests in sand in a geotechnical centrifuge at 50g at a range of target trench depths, sand relative densities, and plough velocities. An improved model for predicting cable plough tow force that separates out the key components of resistance and allows tow force prediction without the use of field-derived empirical coefficients is presented. It is demonstrated that the key parameters in this model can be easily determined from in situ cone penetration tests (CPTs), allowing it to be used offshore where site investigation techniques may be more limited compared to onshore locations. The model is validated against the centrifuge cable plough tests, demonstrating it can correctly predict both the static (dry) and rate effect (saturated) tow forces.
- 1 September 2021
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 58 (9) , 1334-1350
Effects of screw pile installation on installation requirements and in-service performance using the discrete element method
Existing guidance on the installation of screw piles suggest that they should be installed in a pitch-matched manner to avoid disturbance to the soil that may have a detrimental effect on the in-service performance of the pile. Recent insights from centrifuge modelling have shown that installing screw piles in this way requires large vertical compressive (or crowd) forces, which is inconsistent with the common assumption that screw piles pull themselves into the ground requiring minimal vertical compressive force. In this paper, through the use of the discrete element method (DEM), the effects of advancement ratio, i.e., the ratio between the vertical displacement per rotation to the geometric pitch of the helix of the screw pile helix, on the installation resistance and in-service capacity of a screw pile is investigated. The findings are further used to assess the applicability of empirical torque capacity correlation factors for large diameter screw piles. The results of the investigation show that it is possible to reduce the required vertical compressive installation force by 96% by reducing the advancement ratio and that although over-flighting a screw pile can decrease the subsequent compressive capacity, it appears to increase the tensile capacity significantly.
- 1 September 2021
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 58 (9) , 1334-1350
Effects of screw pile installation on installation requirements and in-service performance using the discrete element method
Existing guidance on the installation of screw piles suggest that they should be installed in a pitch-matched manner to avoid disturbance to the soil that may have a detrimental effect on the in-service performance of the pile. Recent insights from centrifuge modelling have shown that installing screw piles in this way requires large vertical compressive (or crowd) forces, which is inconsistent with the common assumption that screw piles pull themselves into the ground requiring minimal vertical compressive force. In this paper, through the use of the discrete element method (DEM), the effects of advancement ratio, i.e., the ratio between the vertical displacement per rotation to the geometric pitch of the helix of the screw pile helix, on the installation resistance and in-service capacity of a screw pile is investigated. The findings are further used to assess the applicability of empirical torque capacity correlation factors for large diameter screw piles. The results of the investigation show that it is possible to reduce the required vertical compressive installation force by 96% by reducing the advancement ratio and that although over-flighting a screw pile can decrease the subsequent compressive capacity, it appears to increase the tensile capacity significantly.
- Open Access
- 1 April 2020
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Geotechnical Engineering
- Vol. 174 (3) , 263-278
Numerical analysis of collapse in a deep excavation supported by ground anchors
On 3 October 2013, a global failure occurred in one of the stabilised sections of a deep excavation in Shahrak-e gharb in Tehran. The excavation was supported by ground anchors with enlarged reinforced concrete thrust blocks and sprayed concrete facing. The failure occurred despite the system passing conventional limit equilibrium design and satisfying requirements in terms of allowable displacements. The case of Shahrak-e gharb was modelled using Abaqus in order to understand the soil deformation leading to the failure condition. It was found that a near-surface zone of weaker fill material was responsible for the failure. As the displacements during construction and the soil failure mechanisms were well matched by the numerical model, the case study was considered to be a validation case for the numerical model and a parametric study on the extent to which anchoring bypassed the weaker surface soil was performed. This study showed that proper embedment into competent soils is important as excessive strains can still develop if the anchor bond zone is insufficiently confined, potentially leading to progressive collapse.
- 1 April 2020
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Geotechnical Engineering
- Vol. 174 (3) , 263-278
Open AccessNumerical analysis of collapse in a deep excavation supported by ground anchors
On 3 October 2013, a global failure occurred in one of the stabilised sections of a deep excavation in Shahrak-e gharb in Tehran. The excavation was supported by ground anchors with enlarged reinforced concrete thrust blocks and sprayed concrete facing. The failure occurred despite the system passing conventional limit equilibrium design and satisfying requirements in terms of allowable displacements. The case of Shahrak-e gharb was modelled using Abaqus in order to understand the soil deformation leading to the failure condition. It was found that a near-surface zone of weaker fill material was responsible for the failure. As the displacements during construction and the soil failure mechanisms were well matched by the numerical model, the case study was considered to be a validation case for the numerical model and a parametric study on the extent to which anchoring bypassed the weaker surface soil was performed. This study showed that proper embedment into competent soils is important as excessive strains can still develop if the anchor bond zone is insufficiently confined, potentially leading to progressive collapse.
- Open Access
- 1 January 2020
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 358
On Lagrangian mechanics and the implicit material point method for large deformation elasto-plasticity
- 1 January 2020
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 358
Open AccessOn Lagrangian mechanics and the implicit material point method for large deformation elasto-plasticity
- Open Access
- 1 November 2019
- Published by Emerald Publishing in International Journal of Physical Modelling in Geotechnics
- Vol. 19 (6) , 305-317
Centrifuge testing to verify scaling of offshore pipeline ploughs
Offshore pipeline ploughs have previously been modelled at 1g with small 1:50 scale models designed to derive the parameters required for prediction of ploughing in terms of tow force requirements and potential advance rates. This was scaled up to prototype with the validity of the scaling verified through ‘modelling of models’ and with comparison to typical prototype tow forces but without direct validation. To allow further validation, a long centrifuge box and actuation system was developed for use on a medium-sized beam centrifuge. Previous approaches to 1g ploughing were also improved through the use of micro-electro-mechanical systems accelerometers and new low-cost surface scanning techniques. A wide range of ploughing velocities were explored through increasing actuation speeds and the use of pore fluids of different viscosities. The study has shown that although there may be initial concerns over low effective stress scaling issues at 1g, in shallow problems with small-scale models, the large deformation nature of the ploughing problem can be replicated with appropriate scaling. This allows the use of 1g modelling for more efficient parametric studies for this application and has given further confidence to performance parameters for prototype modelling derived from 1g and centrifuge studies.
- 1 November 2019
- Published by Emerald Publishing in International Journal of Physical Modelling in Geotechnics
- Vol. 19 (6) , 305-317
Open AccessCentrifuge testing to verify scaling of offshore pipeline ploughs
Offshore pipeline ploughs have previously been modelled at 1g with small 1:50 scale models designed to derive the parameters required for prediction of ploughing in terms of tow force requirements and potential advance rates. This was scaled up to prototype with the validity of the scaling verified through ‘modelling of models’ and with comparison to typical prototype tow forces but without direct validation. To allow further validation, a long centrifuge box and actuation system was developed for use on a medium-sized beam centrifuge. Previous approaches to 1g ploughing were also improved through the use of micro-electro-mechanical systems accelerometers and new low-cost surface scanning techniques. A wide range of ploughing velocities were explored through increasing actuation speeds and the use of pore fluids of different viscosities. The study has shown that although there may be initial concerns over low effective stress scaling issues at 1g, in shallow problems with small-scale models, the large deformation nature of the ploughing problem can be replicated with appropriate scaling. This allows the use of 1g modelling for more efficient parametric studies for this application and has given further confidence to performance parameters for prototype modelling derived from 1g and centrifuge studies.
- Open Access
- 1 October 2019
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 355, 1003-1025
On the use of domain-based material point methods for problems involving large distortion
- 1 October 2019
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 355, 1003-1025
Open AccessOn the use of domain-based material point methods for problems involving large distortion