William Michael Coombs
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
William Michael Coombs has a total of 113 co-authors. Here are the top co-authors by number of shared publications:
- Charles Edward Augarde
Department of Engineering, Durham University, Durham, UK
22 shared publications Charles E. Augarde
Department of Engineering Durham University South Road DH1 3LE Durham UK
19 shared publications- Michael John Brown
School of Science and Engineering, University of Dundee, Dundee, UK
16 shared publications - Robert E. Bird
Department of Engineering Durham University Durham UK
13 shared publications - Andrew Brennan
School of Science and Engineering, University of Dundee, Dundee, UK
11 shared publications - Giuliano Pretti
Department of Engineering Durham University Durham UK
11 shared publications
Latest Publications
- Open Access
- 21 October 2026
- Published by The Royal Society in Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 482 (2348)
Evolving shear bands in a nonlinear micropolar continuum
Shear bands in inelastic solids are often treated as stationary failure zones whose orientation is fixed at bifurcation, a view reinforced by classical Cauchy continua with softening and no internal length scale, where loss of ellipticity drives deformation into a single planar band. Experiments in granular media, however, increasingly show curved, branching and migrating shear zones. Here, we study finite-strain localization in a geometrically nonlinear micropolar (Cosserat) continuum implemented in an implicit material point method, using a non-associative Drucker–Prager model with a unified yield surface based on a generalized measure of stresses and couple stresses to introduce an intrinsic length scale. Two-dimensional boundary-value problems show that localization need not remain rectilinear or stationary: the active zone can curve, reorient and migrate as the stress state evolves, without ad hoc parameter tuning. Viewed through the microrotation field, the evolving centreline is consistently traced by a near-zero ridge of the band-normal microrotation gradient, which we propose as a natural band-selection rule in the nonlinear micropolar continuum.
- 21 October 2026
- Published by The Royal Society in Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 482 (2348)
Open AccessEvolving shear bands in a nonlinear micropolar continuum
Shear bands in inelastic solids are often treated as stationary failure zones whose orientation is fixed at bifurcation, a view reinforced by classical Cauchy continua with softening and no internal length scale, where loss of ellipticity drives deformation into a single planar band. Experiments in granular media, however, increasingly show curved, branching and migrating shear zones. Here, we study finite-strain localization in a geometrically nonlinear micropolar (Cosserat) continuum implemented in an implicit material point method, using a non-associative Drucker–Prager model with a unified yield surface based on a generalized measure of stresses and couple stresses to introduce an intrinsic length scale. Two-dimensional boundary-value problems show that localization need not remain rectilinear or stationary: the active zone can curve, reorient and migrate as the stress state evolves, without ad hoc parameter tuning. Viewed through the microrotation field, the evolving centreline is consistently traced by a near-zero ridge of the band-normal microrotation gradient, which we propose as a natural band-selection rule in the nonlinear micropolar continuum.
- Open Access
- 12 September 2026
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 463
An implicit octree-based adaptive material point method
- 12 September 2026
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 463
Open AccessAn implicit octree-based adaptive material point method
- Open Access
- 7 August 2026
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 44 (6) , 332
Finite Element Bayesian Inference Using Dual Ensemble Kalman Filters for Uncertainty Reduction in Geotechnical Models
The reliability of a geotechnical simulation depends strongly on the selection of material parameters and in recent years Bayesian Inference (BI) has become a popular coherent framework for this task. It has generally been used to reduce the uncertainties based on measurements, but it is challenging due to material non-linearity and paucity of measurement data. Applications to geotechnics of BI to date have struggled with the high dimensionality of the modelled problems (e.g. in 3D FEA) and many studies report considerable computational time needed to achieve the accuracy one might hope to get via an expert assessment. In this paper we introduce a Finite Element–BI (FE–BI) system for geotechnics using a two stage process where the material parameters and the simulation results themselves (the “states”) are updated one after the other. The method is demonstrated on three examples with increasing complexity: parameter determination for undrained compression triaxial tests with the modified Cam clay model; parameter determination from FE simulation of cyclic triaxial tests with the Small Strain Overlay (SSO) model, and 3D FE simulations of a braced excavation. Results show that the FE-BI system can effectively infer both the parameters and states, reducing uncertainty in parameter and state distributions, giving good agreement with the reference solutions provided. The technique proposed in this paper provides a rigorous and efficient approach to obtain material parameters with greater certainty, and could have wide application in geotechnical engineering practice.
- 7 August 2026
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 44 (6) , 332
Open AccessFinite Element Bayesian Inference Using Dual Ensemble Kalman Filters for Uncertainty Reduction in Geotechnical Models
The reliability of a geotechnical simulation depends strongly on the selection of material parameters and in recent years Bayesian Inference (BI) has become a popular coherent framework for this task. It has generally been used to reduce the uncertainties based on measurements, but it is challenging due to material non-linearity and paucity of measurement data. Applications to geotechnics of BI to date have struggled with the high dimensionality of the modelled problems (e.g. in 3D FEA) and many studies report considerable computational time needed to achieve the accuracy one might hope to get via an expert assessment. In this paper we introduce a Finite Element–BI (FE–BI) system for geotechnics using a two stage process where the material parameters and the simulation results themselves (the “states”) are updated one after the other. The method is demonstrated on three examples with increasing complexity: parameter determination for undrained compression triaxial tests with the modified Cam clay model; parameter determination from FE simulation of cyclic triaxial tests with the Small Strain Overlay (SSO) model, and 3D FE simulations of a braced excavation. Results show that the FE-BI system can effectively infer both the parameters and states, reducing uncertainty in parameter and state distributions, giving good agreement with the reference solutions provided. The technique proposed in this paper provides a rigorous and efficient approach to obtain material parameters with greater certainty, and could have wide application in geotechnical engineering practice.
- Open Access
- 27 July 2026
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 127 (14) , e70384
A Matrix‐Free, Scalable, and Robust Implicit Material Point Method
An implicit material point method is presented using a new dynamic relaxation solver, allowing for a simple and efficient quasi‐static formulation that may be readily implemented in existing explicit‐dynamic codes. The use of dynamic relaxation and aggregation is shown to produce an extremely robust material point method scheme, with good convergence characteristics across a range of challenging problems. A new simple fictitious mass matrix formulation based on estimated wave‐speed is derived and presented, allowing for the trivial restructuring of explicit dynamic codes to implicit to solve quasi‐static problems. Finally, a range of large deformation quasi‐static problems, both elastic and elasto‐plastic, are used to demonstrate the convergence characteristics of the method.
- 27 July 2026
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 127 (14) , e70384
Open AccessA Matrix‐Free, Scalable, and Robust Implicit Material Point Method
An implicit material point method is presented using a new dynamic relaxation solver, allowing for a simple and efficient quasi‐static formulation that may be readily implemented in existing explicit‐dynamic codes. The use of dynamic relaxation and aggregation is shown to produce an extremely robust material point method scheme, with good convergence characteristics across a range of challenging problems. A new simple fictitious mass matrix formulation based on estimated wave‐speed is derived and presented, allowing for the trivial restructuring of explicit dynamic codes to implicit to solve quasi‐static problems. Finally, a range of large deformation quasi‐static problems, both elastic and elasto‐plastic, are used to demonstrate the convergence characteristics of the method.
- Open Access
- 7 July 2026
- Published by Elsevier in Ocean Engineering
- Vol. 364
Drag embedment anchor penetration in layered sands and through cable and pipeline trenches
- 7 July 2026
- Published by Elsevier in Ocean Engineering
- Vol. 364
Open AccessDrag embedment anchor penetration in layered sands and through cable and pipeline trenches
- Open Access
- 30 April 2026
- Published by Elsevier in Ocean Engineering
- Vol. 358
Three-dimensional modelling of drag anchor penetration using the material point method
- 30 April 2026
- Published by Elsevier in Ocean Engineering
- Vol. 358
Open AccessThree-dimensional modelling of drag anchor penetration using the material point method
- Open Access
- 21 April 2026
- Published by Elsevier in Composites Communications
- Vol. 64
Efficient 3D analysis of composite laminates using high-aspect-ratio discontinuous Galerkin finite elements
- 21 April 2026
- Published by Elsevier in Composites Communications
- Vol. 64
Open AccessEfficient 3D analysis of composite laminates using high-aspect-ratio discontinuous Galerkin finite elements
- 16 December 2025
- Published by Emerald Publishing in Géotechnique Letters
- Vol. 16 (1) , 77-81
Effect of drag rates on drag embedment anchor penetration for cable burial risk assessment
Cable burial risk assessment (CBRA) defines minimum seabed burial depth of cables to avoid interaction with towed objects that penetrate the seabed, for example, drag embedment anchors (DEA). Recent physical modelling studies have shown that model anchors dragged in dry sand may penetrate to much greater depths in loose sand than current CBRA approaches predict. As other seabed penetrating objects (e.g. pipeline ploughs) have shown velocity or rate of pull dependent behaviour in saturated soils, it is necessary to check for similar rate-dependent penetration behaviour for DEAs. This is required to verify the effect of anchor drag rates in CBRA methods and the validity of previous modelling studies that differ in their findings from current CBRA. This study used model centrifuge tests of DEAs pulled at varying rates in saturated conditions. The result show that anchor penetration depths are reduced with increasing drag rates. The results also confirm that CBRA assumptions of anchor orientation are not consistent with observed behaviour and soil penetration factors require updating. The results suggest that CBRA approaches should also consider the drag speed of the penetration event as this may vary during emergency deployment or may be much lower where a vessel drifts at anchor.
- 16 December 2025
- Published by Emerald Publishing in Géotechnique Letters
- Vol. 16 (1) , 77-81
Effect of drag rates on drag embedment anchor penetration for cable burial risk assessment
Cable burial risk assessment (CBRA) defines minimum seabed burial depth of cables to avoid interaction with towed objects that penetrate the seabed, for example, drag embedment anchors (DEA). Recent physical modelling studies have shown that model anchors dragged in dry sand may penetrate to much greater depths in loose sand than current CBRA approaches predict. As other seabed penetrating objects (e.g. pipeline ploughs) have shown velocity or rate of pull dependent behaviour in saturated soils, it is necessary to check for similar rate-dependent penetration behaviour for DEAs. This is required to verify the effect of anchor drag rates in CBRA methods and the validity of previous modelling studies that differ in their findings from current CBRA. This study used model centrifuge tests of DEAs pulled at varying rates in saturated conditions. The result show that anchor penetration depths are reduced with increasing drag rates. The results also confirm that CBRA assumptions of anchor orientation are not consistent with observed behaviour and soil penetration factors require updating. The results suggest that CBRA approaches should also consider the drag speed of the penetration event as this may vary during emergency deployment or may be much lower where a vessel drifts at anchor.
- Open Access
Three-dimensional modelling of drag anchor penetration using the material point method
Drag embedment anchors are a key threat to buried subsea linear infrastructure, such as power/data cables and pipelines. For cables, selecting a burial depth is a compromise between protecting the cable from anchor strike and the increased cost of deeper installation. This presents an efficient large deformation, elasto-plastic Material Point Method-based soil-structure interaction predictive tool for the estimation of anchor penetration based on Cone Penetration Test (CPT) site investigation data. The tool builds on earlier work by the authors supplemented by three developments: modelling assemblies of rigid bodies (necessary for articulated anchors), a partitioned domain approach to enable accurate and efficient modelling of long anchor pulls and an improved means of modelling rotational inertia. The tool is validated against scaled physical tests conducted in a geotechnical centrifuge on sands with a range of relative densities with good agreement across the tested conditions. Numerical simulations identify key issues with the UK Cable Burial Risk Assessment (CBRA) approach for estimating anchor penetration and reveal the potentially non-conservatism of the CBRA framework for sandy seabeds. The numerical model enables site-specific anchor-penetration assessment along cable routes and can be used to evaluate the performance of different anchor designs and sizes in varied soil conditions.
Open AccessThree-dimensional modelling of drag anchor penetration using the material point method
Drag embedment anchors are a key threat to buried subsea linear infrastructure, such as power/data cables and pipelines. For cables, selecting a burial depth is a compromise between protecting the cable from anchor strike and the increased cost of deeper installation. This presents an efficient large deformation, elasto-plastic Material Point Method-based soil-structure interaction predictive tool for the estimation of anchor penetration based on Cone Penetration Test (CPT) site investigation data. The tool builds on earlier work by the authors supplemented by three developments: modelling assemblies of rigid bodies (necessary for articulated anchors), a partitioned domain approach to enable accurate and efficient modelling of long anchor pulls and an improved means of modelling rotational inertia. The tool is validated against scaled physical tests conducted in a geotechnical centrifuge on sands with a range of relative densities with good agreement across the tested conditions. Numerical simulations identify key issues with the UK Cable Burial Risk Assessment (CBRA) approach for estimating anchor penetration and reveal the potentially non-conservatism of the CBRA framework for sandy seabeds. The numerical model enables site-specific anchor-penetration assessment along cable routes and can be used to evaluate the performance of different anchor designs and sizes in varied soil conditions.
- Open Access
- 27 November 2025
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 126 (23)
Including Pre‐Existing Fractures in Phase Field Fracture Models
The phase field method for fracture modelling has, in recent years, become the method of choice for complex fracture problems, especially those involving branching, merging, or nucleating fractures. As the number of applications of the phase field method has expanded, the importance of assessing its accuracy has increased. One important factor in enabling the production of accurate results is making appropriate choices to include pre‐existing fractures in the model setup. In this work, seven methods for including pre‐existing fractures are identified—six from existing literature, and one new method derived from the phase field energy functional. These methods are tested in their ability to reproduce an analytical 1D solution for their phase field, and their performance in a mode I fracture problem, with their load‐displacement and energy release rate responses analysed. The authors' proposed method exhibits robust performance and shows promise in matching theoretical predictions and reducing computational cost in some settings.
- 27 November 2025
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 126 (23)
Open AccessIncluding Pre‐Existing Fractures in Phase Field Fracture Models
The phase field method for fracture modelling has, in recent years, become the method of choice for complex fracture problems, especially those involving branching, merging, or nucleating fractures. As the number of applications of the phase field method has expanded, the importance of assessing its accuracy has increased. One important factor in enabling the production of accurate results is making appropriate choices to include pre‐existing fractures in the model setup. In this work, seven methods for including pre‐existing fractures are identified—six from existing literature, and one new method derived from the phase field energy functional. These methods are tested in their ability to reproduce an analytical 1D solution for their phase field, and their performance in a mode I fracture problem, with their load‐displacement and energy release rate responses analysed. The authors' proposed method exhibits robust performance and shows promise in matching theoretical predictions and reducing computational cost in some settings.