Gyubaek An
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gyubaek An has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Jeongung Park
Department of Civil Engineering, Chosun University, Gwangju 61452, Republic of Korea
24 shared publications - Daehee Seong
Department of Naval Architecture & Ocean Engineering, Chosun University, Gwangju 61452, Republic of Korea
6 shared publications - Jiseung Lee
Department of Naval Architecture & Ocean Engineering Chosun University 61452 Gwangju Korea
4 shared publications - Wonjun Jo
Department of Naval Architecture & Ocean Engineering, Chosun University, Gwangju 61452, Republic of Korea
4 shared publications - Hongyeol Bae
Technical Research Laboratories, POSCO, Pohang, 37553, Republic of Korea
3 shared publications - Ilwook Han
Technical Research Laboratory, POSCO, Pohang 37859, Korea
3 shared publications
Latest Publications
- Open Access
- 31 October 2026
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 44  (5) , 516-536
Experimental Methods for Assessing Mechanical Properties and Fracture Resistance of Steels from LNG to Liquid-Hydrogen Temperatures: A Critical Review
Qualification of metallic structures for liquefied natural gas (LNG), liquid nitrogen, liquid hydrogen, and other low-temperature services requires a mechanical-property database that is consistent with the relevant failure mode. Tensile strength, Charpy energy, drop-weight tear-test (DWTT) shear area, J-R resistance, CTOD, KJc/T0, fatigue- crack-growth rate, and crack-arrest toughness are not interchangeable measures, because each interrogates a different stage of failure under a different constraint and loading condition. This review critically examines experimental methods for characterizing mechanical properties and fracture resistance of steels and welded joints from LNG service near -163 °C down to liquid-hydrogen temperature (20 K). A total of 105 peer-reviewed studies, standards, and technical reports covering X70 line-pipe steel, 9%Ni steel, EH36/EH47 and offshore steels, high-Mn steels, weld heat-affected zones (HAZs), hydrogen-assisted fracture, small-scale testing, and crack-arrest evaluation are assessed against the requirements of quantitative flaw assessment. Particular attention is given to temperature control, fatigue precracking, notch acuity, specimen size and constraint, HAZ notch placement, crack-growth measurement, hydrogen charging history, and the distinction between crack initiation and arrest. Literature figures and selected source-based schematics illustrate the reviewed methods; their sources and presentation types are identified in the captions. Evidence obtained above 20 K is treated as methodological or screening evidence, not as direct qualification for liquid-hydrogen service. A test-selection framework is proposed that links the intended structural question to the corresponding specimen geometry, fracture parameter, and validity criteria. The principal conclusion is that a defensible cryogenic property cannot be defined only by a low test temperature: validity requires equivalence among service condition, specimen constraint, crack geometry, loading rate, environmental history, and the selected fracture parameter.
- 31 October 2026
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 44  (5) , 516-536
Open AccessExperimental Methods for Assessing Mechanical Properties and Fracture Resistance of Steels from LNG to Liquid-Hydrogen Temperatures: A Critical Review
Qualification of metallic structures for liquefied natural gas (LNG), liquid nitrogen, liquid hydrogen, and other low-temperature services requires a mechanical-property database that is consistent with the relevant failure mode. Tensile strength, Charpy energy, drop-weight tear-test (DWTT) shear area, J-R resistance, CTOD, KJc/T0, fatigue- crack-growth rate, and crack-arrest toughness are not interchangeable measures, because each interrogates a different stage of failure under a different constraint and loading condition. This review critically examines experimental methods for characterizing mechanical properties and fracture resistance of steels and welded joints from LNG service near -163 °C down to liquid-hydrogen temperature (20 K). A total of 105 peer-reviewed studies, standards, and technical reports covering X70 line-pipe steel, 9%Ni steel, EH36/EH47 and offshore steels, high-Mn steels, weld heat-affected zones (HAZs), hydrogen-assisted fracture, small-scale testing, and crack-arrest evaluation are assessed against the requirements of quantitative flaw assessment. Particular attention is given to temperature control, fatigue precracking, notch acuity, specimen size and constraint, HAZ notch placement, crack-growth measurement, hydrogen charging history, and the distinction between crack initiation and arrest. Literature figures and selected source-based schematics illustrate the reviewed methods; their sources and presentation types are identified in the captions. Evidence obtained above 20 K is treated as methodological or screening evidence, not as direct qualification for liquid-hydrogen service. A test-selection framework is proposed that links the intended structural question to the corresponding specimen geometry, fracture parameter, and validity criteria. The principal conclusion is that a defensible cryogenic property cannot be defined only by a low test temperature: validity requires equivalence among service condition, specimen constraint, crack geometry, loading rate, environmental history, and the selected fracture parameter.
- Open Access
Effect of Material Property Factors on the Interfacial Residual Stress Gradient in High-Manganese Steel/STS304 Dissimilar Butt Welds
Cryogenic high-manganese austenitic steel is used in liquefied natural gas (LNG) storage tanks and has a lower thermal expansion coefficient than other cryogenic steels. Because it is joined to stainless steel in the loading system, dissimilar welding is required. Three-dimensional thermal elastic–plastic finite element analysis and sectioning measurements were performed on 15-mm-thick high-manganese steel/STS304 dissimilar butt welds, and the residual stress was analysed separately in the longitudinal and transverse components. The analysis predicted a steep gradient at the weld metal–STS304 interface 8.5 mm from the weld centre, where the transverse stress falls to about −230 MPa. The longitudinal peak differed from the homogeneous joint by only 77 MPa (−11.7%), within the analysis–measurement deviation (RMSE 103–127 MPa). Of the four properties substituted individually, the expansion coefficient gave the highest reproduction ratio (57.9% on average) and alone reproduced the interfacial compression; substituting all four reproduced the effect almost completely (102.4%). The transverse stress range increased linearly with the expansion mismatch (R2 = 0.978), whereas the longitudinal range did not (R2 = 0.002). Assessment by peak residual stress alone therefore misses the interfacial gradient and the compressive zone specific to dissimilar joints.
Open AccessEffect of Material Property Factors on the Interfacial Residual Stress Gradient in High-Manganese Steel/STS304 Dissimilar Butt Welds
Cryogenic high-manganese austenitic steel is used in liquefied natural gas (LNG) storage tanks and has a lower thermal expansion coefficient than other cryogenic steels. Because it is joined to stainless steel in the loading system, dissimilar welding is required. Three-dimensional thermal elastic–plastic finite element analysis and sectioning measurements were performed on 15-mm-thick high-manganese steel/STS304 dissimilar butt welds, and the residual stress was analysed separately in the longitudinal and transverse components. The analysis predicted a steep gradient at the weld metal–STS304 interface 8.5 mm from the weld centre, where the transverse stress falls to about −230 MPa. The longitudinal peak differed from the homogeneous joint by only 77 MPa (−11.7%), within the analysis–measurement deviation (RMSE 103–127 MPa). Of the four properties substituted individually, the expansion coefficient gave the highest reproduction ratio (57.9% on average) and alone reproduced the interfacial compression; substituting all four reproduced the effect almost completely (102.4%). The transverse stress range increased linearly with the expansion mismatch (R2 = 0.978), whereas the longitudinal range did not (R2 = 0.002). Assessment by peak residual stress alone therefore misses the interfacial gradient and the compressive zone specific to dissimilar joints.
- 22 August 2026
- Published by Elsevier in Ocean Engineering
- Vol. 366
Fracture toughness prediction of weld heat affected zone based on small scale specimens
- 22 August 2026
- Published by Elsevier in Ocean Engineering
- Vol. 366
Fracture toughness prediction of weld heat affected zone based on small scale specimens
- Open Access
- 18 June 2026
- Published by Elsevier in SSRN Electronic Journal
Fracture toughness prediction of weld heat affected zone based on small scale specimens
This paper proposes a small scale specimen-based methodology for predicting the fracture toughness of welded heat affected zones (HAZ) by considering local microstructural fractions. Locally heterogeneous HAZ microstructures such as CGHAZ and SCHAZ are created owing to complex thermal cycles experienced by welded joints. To establish the proposed methodology, small scale simulated HAZ specimens are prepared, and their fracture toughness is evaluated using electrical discharge machining-notched specimens. The local HAZ microstructural fractions at the notch tip of the specimens are quantified and incorporated into small scale fracture toughness prediction models. Subsequently, the predicted fracture toughness values of the small scale welded HAZ specimens are converted into full thickness welded HAZ fracture toughness values. Local and normalized relative sensitivity analyses are performed to identify the dominant variables affecting the prediction results. The predicted fracture toughness values agree well with experimentally measured values. Sensitivity analysis shows that the proposed framework is governed by three main factors. In both the CGHAZ and SCHAZ models, the local HAZ fraction and thickness ratio directly affect the final predicted fracture toughness values. The small scale specimen-based prediction approach accurately reflects the microstructural heterogeneity of actual welded HAZ specimens while maintaining engineering relevance for welded-joint assessments.
- 18 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessFracture toughness prediction of weld heat affected zone based on small scale specimens
This paper proposes a small scale specimen-based methodology for predicting the fracture toughness of welded heat affected zones (HAZ) by considering local microstructural fractions. Locally heterogeneous HAZ microstructures such as CGHAZ and SCHAZ are created owing to complex thermal cycles experienced by welded joints. To establish the proposed methodology, small scale simulated HAZ specimens are prepared, and their fracture toughness is evaluated using electrical discharge machining-notched specimens. The local HAZ microstructural fractions at the notch tip of the specimens are quantified and incorporated into small scale fracture toughness prediction models. Subsequently, the predicted fracture toughness values of the small scale welded HAZ specimens are converted into full thickness welded HAZ fracture toughness values. Local and normalized relative sensitivity analyses are performed to identify the dominant variables affecting the prediction results. The predicted fracture toughness values agree well with experimentally measured values. Sensitivity analysis shows that the proposed framework is governed by three main factors. In both the CGHAZ and SCHAZ models, the local HAZ fraction and thickness ratio directly affect the final predicted fracture toughness values. The small scale specimen-based prediction approach accurately reflects the microstructural heterogeneity of actual welded HAZ specimens while maintaining engineering relevance for welded-joint assessments.
- Open Access
- 13 May 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of plastic behavior on the fracture behavior of high manganese austenitic steel welded joints under cryogenic temperatures
Plastic deformation from fabrication or seismic events can degrade the fracture toughness of high-manganese (H-Mn) austenitic steel, which is a cryogenic steel used to ensure fracture safety when upscaling liquified natural gas storage tanks. In this study, crack tip opening displacement (CTOD) tests were conducted at -165 °C on H-Mn steel weld joints at pre-strain levels of 0%, 5%, and 10% and the resistance to ductile crack propagation was analyzed using CTOD(δ)–R curves. Results indicated that CTOD values of the weld metal (WM) and heat-affected zone (HAZ) decreased markedly with increasing pre-strain. Although relatively high CTOD values were obtained in the WM and HAZ regions under 0% pre-strain, they decreased significantly under 5% and 10% pre-strain, indicating deterioration in fracture resistance under cryogenic conditions. Lowest CTOD values were observed at 10% pre-strain, confirming that increasing pre-strain reduces crack-tip plastic deformation capacity and fracture resistance. The CTOD(δ)-R curve analysis showed that the weld metal without pre-strain exhibited a relatively large allowable crack length under the design stress condition. In contrast, crack-growth resistance decreased with an increase in the pre-strain level. Therefore, the fracture safety assessment of H-Mn steel weld metal under cryogenic conditions should consider not only brittle fracture initiation but also the resistance to ductile crack growth and the possibility of unstable ductile fracture as a function of pre-strain. This study is expected to provide a useful basis for establishing fracture assessment criteria that incorporate the effect of pre-strain in the safety evaluation of cryogenic H-Mn steel welded structures.
- 13 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of plastic behavior on the fracture behavior of high manganese austenitic steel welded joints under cryogenic temperatures
Plastic deformation from fabrication or seismic events can degrade the fracture toughness of high-manganese (H-Mn) austenitic steel, which is a cryogenic steel used to ensure fracture safety when upscaling liquified natural gas storage tanks. In this study, crack tip opening displacement (CTOD) tests were conducted at -165 °C on H-Mn steel weld joints at pre-strain levels of 0%, 5%, and 10% and the resistance to ductile crack propagation was analyzed using CTOD(δ)–R curves. Results indicated that CTOD values of the weld metal (WM) and heat-affected zone (HAZ) decreased markedly with increasing pre-strain. Although relatively high CTOD values were obtained in the WM and HAZ regions under 0% pre-strain, they decreased significantly under 5% and 10% pre-strain, indicating deterioration in fracture resistance under cryogenic conditions. Lowest CTOD values were observed at 10% pre-strain, confirming that increasing pre-strain reduces crack-tip plastic deformation capacity and fracture resistance. The CTOD(δ)-R curve analysis showed that the weld metal without pre-strain exhibited a relatively large allowable crack length under the design stress condition. In contrast, crack-growth resistance decreased with an increase in the pre-strain level. Therefore, the fracture safety assessment of H-Mn steel weld metal under cryogenic conditions should consider not only brittle fracture initiation but also the resistance to ductile crack growth and the possibility of unstable ductile fracture as a function of pre-strain. This study is expected to provide a useful basis for establishing fracture assessment criteria that incorporate the effect of pre-strain in the safety evaluation of cryogenic H-Mn steel welded structures.
- Open Access
- 31 October 2025
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 43  (5) , 563-580
Performance Evaluation at Cryogenic Temperature with Cryogenic Materials Applications in Ships: A Review
The increasing demand for liquefied hydrogen (LHS) as a clean energy carrier necessitates the development of structural materials capable of withstanding extreme cryogenic conditions. This paper reviews three primary candidate materials austenitic stainless steels, high nickel steels, and high-manganese steels focusing on their mechanical properties, fracture toughness, and susceptibility to hydrogen embrittlement. Austenitic stainless steels provide excellent toughness and hydrogen resistance but are limited by low strength and high cost. Conventional 9%Ni steels have demonstrated reliable performance in LNG service, while newly developed 13-15%Ni steels exhibit stable fracture toughness down to lower temperature, extending their applicability to LH2 environments. High-manganese steels offer an attractive balance of high toughness, strength, and cost effectiveness; however, further validation of hydrogen embrittlement resistance and international standardization are required before large-scale implementation. The comparative evaluation highlights that each alloy system presents distinct advantages and limitations, and that future efforts should focus on comprehensive cryogenic testing and the establishment of consistent qualification standards to ensure safe and efficient deployment of LH2 storage and transportation systems.
- 31 October 2025
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 43  (5) , 563-580
Open AccessPerformance Evaluation at Cryogenic Temperature with Cryogenic Materials Applications in Ships: A Review
The increasing demand for liquefied hydrogen (LHS) as a clean energy carrier necessitates the development of structural materials capable of withstanding extreme cryogenic conditions. This paper reviews three primary candidate materials austenitic stainless steels, high nickel steels, and high-manganese steels focusing on their mechanical properties, fracture toughness, and susceptibility to hydrogen embrittlement. Austenitic stainless steels provide excellent toughness and hydrogen resistance but are limited by low strength and high cost. Conventional 9%Ni steels have demonstrated reliable performance in LNG service, while newly developed 13-15%Ni steels exhibit stable fracture toughness down to lower temperature, extending their applicability to LH2 environments. High-manganese steels offer an attractive balance of high toughness, strength, and cost effectiveness; however, further validation of hydrogen embrittlement resistance and international standardization are required before large-scale implementation. The comparative evaluation highlights that each alloy system presents distinct advantages and limitations, and that future efforts should focus on comprehensive cryogenic testing and the establishment of consistent qualification standards to ensure safe and efficient deployment of LH2 storage and transportation systems.
- Open Access
The Effect of Hydrogen Embrittlement on Fracture Toughness of Cryogenic Steels
This study investigates the effect of hydrogen embrittlement on the fracture toughness of 9% Ni steel and STS 316L stainless steel under cryogenic conditions ranging from −80 °C to −253 °C. Hydrogen charging was performed using electrochemical methods, and hydrogen uptake was quantitatively analyzed using thermal desorption spectroscopy (TDS). Fracture toughness was evaluated using crack tip opening displacement (CTOD) testing per ISO 12135, both without hydrogen (WO-H) and with hydrogen (W-H). The results showed a gradual decrease in CTOD values with decreasing temperature in both steels under hydrogen-free conditions, with ductile fracture maintained even at −253 °C. In contrast, hydrogen-charged specimens exhibited significant toughness degradation at intermediate subzero temperatures (−80 °C to −130 °C), particularly in 9% Ni steel due to its BCC crystal structure. However, at −160 °C and below, the effect of hydrogen embrittlement was suppressed mainly owing to the reduced hydrogen diffusivity. Scanning electron microscopy (SEM) analysis confirmed the transition from ductile to brittle fracture with decreasing temperature and hydrogen influences. At −253 °C, fully brittle fracture surfaces were observed in all specimens, confirming that at ultra-low temperatures, fracture behavior is dominated by temperature effects rather than hydrogen. These findings identify a practical temperature limit (approximately −160 °C) below which hydrogen embrittlement becomes negligible, providing critical insights for the design and application of structural materials in hydrogen cryogenic environments.
Open AccessThe Effect of Hydrogen Embrittlement on Fracture Toughness of Cryogenic Steels
This study investigates the effect of hydrogen embrittlement on the fracture toughness of 9% Ni steel and STS 316L stainless steel under cryogenic conditions ranging from −80 °C to −253 °C. Hydrogen charging was performed using electrochemical methods, and hydrogen uptake was quantitatively analyzed using thermal desorption spectroscopy (TDS). Fracture toughness was evaluated using crack tip opening displacement (CTOD) testing per ISO 12135, both without hydrogen (WO-H) and with hydrogen (W-H). The results showed a gradual decrease in CTOD values with decreasing temperature in both steels under hydrogen-free conditions, with ductile fracture maintained even at −253 °C. In contrast, hydrogen-charged specimens exhibited significant toughness degradation at intermediate subzero temperatures (−80 °C to −130 °C), particularly in 9% Ni steel due to its BCC crystal structure. However, at −160 °C and below, the effect of hydrogen embrittlement was suppressed mainly owing to the reduced hydrogen diffusivity. Scanning electron microscopy (SEM) analysis confirmed the transition from ductile to brittle fracture with decreasing temperature and hydrogen influences. At −253 °C, fully brittle fracture surfaces were observed in all specimens, confirming that at ultra-low temperatures, fracture behavior is dominated by temperature effects rather than hydrogen. These findings identify a practical temperature limit (approximately −160 °C) below which hydrogen embrittlement becomes negligible, providing critical insights for the design and application of structural materials in hydrogen cryogenic environments.
- Open Access
Characteristics of Microstructure and Fracture Toughness According to the Groove Shape of Submerged Arc Welding
This study investigates the effects of heat input on the microstructure and fracture toughness of SAW (Submerged Arc Welding) joints with K-groove and X-groove weld preparations using S460NL steel. Microstructural analysis focused on acicular ferrite, grain boundary ferrite, and MA (Martensite–Austenite) constituents to assess their influence on CTOD (Crack Tip Opening Displacement). The results indicate that the K-groove achieved a higher CTOD value of 0.82 mm compared to 0.13 mm for the X-groove, attributed to differences in microstructural composition and cooling rates. The findings highlight the impact of groove geometry and heat input on weld performance.
Open AccessCharacteristics of Microstructure and Fracture Toughness According to the Groove Shape of Submerged Arc Welding
This study investigates the effects of heat input on the microstructure and fracture toughness of SAW (Submerged Arc Welding) joints with K-groove and X-groove weld preparations using S460NL steel. Microstructural analysis focused on acicular ferrite, grain boundary ferrite, and MA (Martensite–Austenite) constituents to assess their influence on CTOD (Crack Tip Opening Displacement). The results indicate that the K-groove achieved a higher CTOD value of 0.82 mm compared to 0.13 mm for the X-groove, attributed to differences in microstructural composition and cooling rates. The findings highlight the impact of groove geometry and heat input on weld performance.
- Open Access
- 20 December 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14  (24) , 11971
Residual Stress Characteristics in Spot Weld Joints of High-Strength Steel: Influence of Welding Parameters
This study examines the residual stress characteristics of spot welding in newly developed high-strength steel for automotive body construction through experimental and numerical methods. The effects of sheet thickness, nugget size, and the presence or absence of spacers on residual stress distribution and fracture stability were evaluated. Measurements using XRD and HDR revealed tensile residual stress below the yield strength at the nugget center. A numerical analysis system corroborated experimental findings, demonstrating that larger nugget sizes reduce tensile residual stress at the nugget center, enhancing fracture stability. However, for nugget sizes of 3 (t: thickness), high tensile stress at the nugget edge compromised stability, while sizes of 3.5 or larger improved fracture resistance. The study also found that thicker sheets increased fracture safety with larger nugget sizes, and the presence of spacers induced tensile stress through spring-back effects, which shifted to compressive stress as the nugget size increased. These results provide critical insights into optimizing welding parameters to improve the structural integrity of automotive components.- 20 December 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14  (24) , 11971
Open AccessResidual Stress Characteristics in Spot Weld Joints of High-Strength Steel: Influence of Welding Parameters
This study examines the residual stress characteristics of spot welding in newly developed high-strength steel for automotive body construction through experimental and numerical methods. The effects of sheet thickness, nugget size, and the presence or absence of spacers on residual stress distribution and fracture stability were evaluated. Measurements using XRD and HDR revealed tensile residual stress below the yield strength at the nugget center. A numerical analysis system corroborated experimental findings, demonstrating that larger nugget sizes reduce tensile residual stress at the nugget center, enhancing fracture stability. However, for nugget sizes of 3 (t: thickness), high tensile stress at the nugget edge compromised stability, while sizes of 3.5 or larger improved fracture resistance. The study also found that thicker sheets increased fracture safety with larger nugget sizes, and the presence of spacers induced tensile stress through spring-back effects, which shifted to compressive stress as the nugget size increased. These results provide critical insights into optimizing welding parameters to improve the structural integrity of automotive components. - Open Access
- 31 October 2024
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 42  (5) , 521-529
Fracture Toughness Estimate of H-Section Steel for Offshore Structure
In this study, a novel estimating equation based on the WES2808 standard was proposed to predict fracture toughness through the transition temperature of Charpy impact toughness and CTOD (Crack Tip Opening Displacement) fracture toughness. This equation was specifically developed for 460MPa class H-section steel materials used in marine structures, including the base material (BM), heat-affected zone (HAZ), and weld metal (WM). The experimental results confirmed that the proposed estimation equation accurately predicted the fracture toughness across these different material regions. These findings demonstrate the reliability and applicability of the proposed equation in estimated fracture toughness for marine structure materials, thereby contributing to improved safety and performance in harsh environmental conditions.
- 31 October 2024
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 42  (5) , 521-529
Open AccessFracture Toughness Estimate of H-Section Steel for Offshore Structure
In this study, a novel estimating equation based on the WES2808 standard was proposed to predict fracture toughness through the transition temperature of Charpy impact toughness and CTOD (Crack Tip Opening Displacement) fracture toughness. This equation was specifically developed for 460MPa class H-section steel materials used in marine structures, including the base material (BM), heat-affected zone (HAZ), and weld metal (WM). The experimental results confirmed that the proposed estimation equation accurately predicted the fracture toughness across these different material regions. These findings demonstrate the reliability and applicability of the proposed equation in estimated fracture toughness for marine structure materials, thereby contributing to improved safety and performance in harsh environmental conditions.