Xueling Quan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Xueling Quan has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Jinbin Xu
Shanghai Jiao Tong University
4 shared publications Liying Wu
Center for Advanced Electronic Materials and Devices, Shanghai Jiao Tong University, Shanghai, China
3 shared publications- Min Liu
Center for Advanced Electronic Materials and Devices, Shanghai Jiao Tong University, Shanghai, China
3 shared publications Xiulan Cheng
Center for Advanced Electronic Materials and Devices, Shanghai Jiao Tong University, Shanghai, China
3 shared publications- Xiulan Cheng
Shanghai Jiao Tong University
3 shared publications - Sipan Yang
Shanghai Jiao Tong University
2 shared publications
Latest Publications
- 12 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (2) , 701-711
Graded-Index Lens Based Edge Coupler With Low-Loss, Broad Bandwidth for Efficient Coupling Between Silicon Waveguide and Standard Single-Mode Fiber
Efficient fiber-to-chip coupling is crucial for achieving high-performance silicon photonic chips. While lensed fiber to chip coupling has been extensively researched and proven excellent, it does have limitations such as strict alignment tolerance and high cost. Therefore, the recommended approach is the standard single-mode fiber (SMF)-to-chip coupling. One potential solution for SMF-to-chip coupling involves an edge coupler based on a graded-index (GRIN) lens; however, this method often requires a GRIN lens with numerous layers, making fabrication extremely challenging. In this study, we propose and experimentally validate an edge coupler based on a GRIN lens assisted by a complementary taper structure. This new type of composite structure demonstrates low coupling loss, broad bandwidth, and polarization insensitivity, enabling efficient SMF-to-chip coupling. Our design simplifies the fabrication process by significantly reducing the number of layers in the GRIN lens while achieving lower coupling losses compared to conventional GRIN lens-based edge couplers. Experimental results demonstrate that at 1550 nm, the measured TE and TM mode coupling losses are 1.21 dB and 1.78 dB respectively, while maintaining the 1 dB bandwidth exceeding 90 nm.
- 12 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (2) , 701-711
Graded-Index Lens Based Edge Coupler With Low-Loss, Broad Bandwidth for Efficient Coupling Between Silicon Waveguide and Standard Single-Mode Fiber
Efficient fiber-to-chip coupling is crucial for achieving high-performance silicon photonic chips. While lensed fiber to chip coupling has been extensively researched and proven excellent, it does have limitations such as strict alignment tolerance and high cost. Therefore, the recommended approach is the standard single-mode fiber (SMF)-to-chip coupling. One potential solution for SMF-to-chip coupling involves an edge coupler based on a graded-index (GRIN) lens; however, this method often requires a GRIN lens with numerous layers, making fabrication extremely challenging. In this study, we propose and experimentally validate an edge coupler based on a GRIN lens assisted by a complementary taper structure. This new type of composite structure demonstrates low coupling loss, broad bandwidth, and polarization insensitivity, enabling efficient SMF-to-chip coupling. Our design simplifies the fabrication process by significantly reducing the number of layers in the GRIN lens while achieving lower coupling losses compared to conventional GRIN lens-based edge couplers. Experimental results demonstrate that at 1550 nm, the measured TE and TM mode coupling losses are 1.21 dB and 1.78 dB respectively, while maintaining the 1 dB bandwidth exceeding 90 nm.
- 24 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (14) , 765-768
Polarization Insensitive Edge Coupler Assisted by Subwavelength Grating and Suspended Structure
Based on the Si-Si3N4 hybrid photonic platform, an integrated edge coupler embedded with both sub-wavelength grating (SWG) waveguide and suspended structure was demonstrated. The proposed device structure and geometrical parameters were fully optimized to realize efficient optical interconnections with standard single-mode fiber (SMF-28). The coupling loss of 0.86 dB/port for TE mode and 0.94 dB/port for TM mode was achieved with a remarkable polarization dependent loss (PDL) less than 0.1 dB at the input wavelength of 1600 nm. It revealed that the integrated edge coupler assisted by sub-wavelength grating can further reduce the PDL. Moreover, the device also exhibited the advantages of large alignment tolerance. The alignment tolerances for 1-dB excess loss are ±1.8 and ±2.5 μm in horizontal and vertical direction, respectively.
- 24 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (14) , 765-768
Polarization Insensitive Edge Coupler Assisted by Subwavelength Grating and Suspended Structure
Based on the Si-Si3N4 hybrid photonic platform, an integrated edge coupler embedded with both sub-wavelength grating (SWG) waveguide and suspended structure was demonstrated. The proposed device structure and geometrical parameters were fully optimized to realize efficient optical interconnections with standard single-mode fiber (SMF-28). The coupling loss of 0.86 dB/port for TE mode and 0.94 dB/port for TM mode was achieved with a remarkable polarization dependent loss (PDL) less than 0.1 dB at the input wavelength of 1600 nm. It revealed that the integrated edge coupler assisted by sub-wavelength grating can further reduce the PDL. Moreover, the device also exhibited the advantages of large alignment tolerance. The alignment tolerances for 1-dB excess loss are ±1.8 and ±2.5 μm in horizontal and vertical direction, respectively.
- 27 March 2022
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12169, 206-1038
Waveguide integrated trapezoidal germanium photodetector based on lateral PIN junction in SOI
Photodetector (PD) is considered as a key component in the applications of optical communications. With the technology development of germanium (Ge) epitaxy on silicon, the research on waveguide integrated germanium photodetector is becoming more popular for its good photo-response characteristics in the infrared wavelength band. However, to the best of our knowledge, the influence of Ge layer shape on the performance of photodetectors has not been paid attention yet. In this paper, the influence of different shapes of germanium layer on the performance of photodetectors was explored by using the simulation software of Lumerical FDTD and DEVICE. Moreover, responsivity and 3-dB bandwidth on mature silicon-on-insulator (SOI) platform were further studied, respectively. The morphology of epitaxial Ge layer in the lateral PIN-type waveguide integrated photodetector was fully optimized, and the photodetectors theoretically exhibit excellent output performance at the wavelength of 1550nm with a bias voltage of -1 V. Furthermore, the responsivity and 3-dB bandwidth of the trapezoidal Ge photodetectors are obviously higher than that of traditional rectangular germanium photodetectors with lower dark current. In detail, the responsivity in our proposed photodetector structure is 1.04 A/W, the 3-dB bandwidth is as high as 30.8 GHz, and the dark current is as low as 97 nA.
- 27 March 2022
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12169, 206-1038
Waveguide integrated trapezoidal germanium photodetector based on lateral PIN junction in SOI
Photodetector (PD) is considered as a key component in the applications of optical communications. With the technology development of germanium (Ge) epitaxy on silicon, the research on waveguide integrated germanium photodetector is becoming more popular for its good photo-response characteristics in the infrared wavelength band. However, to the best of our knowledge, the influence of Ge layer shape on the performance of photodetectors has not been paid attention yet. In this paper, the influence of different shapes of germanium layer on the performance of photodetectors was explored by using the simulation software of Lumerical FDTD and DEVICE. Moreover, responsivity and 3-dB bandwidth on mature silicon-on-insulator (SOI) platform were further studied, respectively. The morphology of epitaxial Ge layer in the lateral PIN-type waveguide integrated photodetector was fully optimized, and the photodetectors theoretically exhibit excellent output performance at the wavelength of 1550nm with a bias voltage of -1 V. Furthermore, the responsivity and 3-dB bandwidth of the trapezoidal Ge photodetectors are obviously higher than that of traditional rectangular germanium photodetectors with lower dark current. In detail, the responsivity in our proposed photodetector structure is 1.04 A/W, the 3-dB bandwidth is as high as 30.8 GHz, and the dark current is as low as 97 nA.
- Open Access
- 2 August 2021
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 32 (17) , 21932-21943
Highly-efficient thin film LiNbO3 surface couplers connected by ridge-waveguide subwavelength gratings
- 2 August 2021
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 32 (17) , 21932-21943
Open AccessHighly-efficient thin film LiNbO3 surface couplers connected by ridge-waveguide subwavelength gratings
- 25 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 31 (5) , 349-352
Silicon-Nitride-Assisted Edge Coupler Interfacing With High Numerical Aperture Fiber
Reducing the mode size mismatch between high-index-contrast silicon waveguide and single mode fiber takes an important role in photonic integration. A low-loss and broadband silicon nitride assisted edge coupler for coupling of light between silicon wire waveguides and high numerical aperture fiber is proposed and optimized for TE polarization. The mode size converter is composed of silicon inverse taper waveguides in core and two silicon nitride interlayers spaced by silica in cladding layers. The edge coupler is characterized with cleaved high numerical aperture fiber (mode field diameter is about 6.5 μm). With the help of refractive index matching oil (n = 1.46), the coupling loss for TE polarized light input is 0.35 dB at 1570 nm. The 1-dB bandwidth is 95 nm. The 1-dB alignment tolerances are higher than ± 2.5 μm and ± 1 μm in the horizontal and vertical directions, respectively, and higher than 25 μm in axial direction.
- 25 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 31 (5) , 349-352
Silicon-Nitride-Assisted Edge Coupler Interfacing With High Numerical Aperture Fiber
Reducing the mode size mismatch between high-index-contrast silicon waveguide and single mode fiber takes an important role in photonic integration. A low-loss and broadband silicon nitride assisted edge coupler for coupling of light between silicon wire waveguides and high numerical aperture fiber is proposed and optimized for TE polarization. The mode size converter is composed of silicon inverse taper waveguides in core and two silicon nitride interlayers spaced by silica in cladding layers. The edge coupler is characterized with cleaved high numerical aperture fiber (mode field diameter is about 6.5 μm). With the help of refractive index matching oil (n = 1.46), the coupling loss for TE polarized light input is 0.35 dB at 1570 nm. The 1-dB bandwidth is 95 nm. The 1-dB alignment tolerances are higher than ± 2.5 μm and ± 1 μm in the horizontal and vertical directions, respectively, and higher than 25 μm in axial direction.
- Open Access
- 4 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 10 (5) , 1-7
Ultra-Small and Fabrication-Tolerant Silicon Polarization Beam Splitter Using Sharp Bent Directional Coupler
An ultra-small polarization beam splitter on silicon-on-insulator platform is proposed and demonstrated experimentally employing a sharp bent directional coupler. The coupling length of our device is only 0.764 μ m. High-efficient selective coupling can be achieved benefiting from the inner bend chosen as Through port and ultra-small bend (radii are about 3 μ m) used in Through and Cross waveguides. The measured excess loss is less than 1 dB and extinction ratio is 15–20 dB for TM polarization, meanwhile, the measured excess loss is less than 2 dB and extinction ratio is 15-16 dB for TE polarization in a wavelength range from 1540 nm to 1580 nm. The fabrication tolerance to variation of waveguide width is also demonstrated. When the waveguide widths of the Through and Cross waveguides vary from −24 nm to +12 nm, the measured excess losses remain lower than 2 dB and the extinction ratios are higher than 10 dB for both polarizations. The footprint of the fabricated device is just 1.5 μ m × 1.3 μ m.
- 4 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 10 (5) , 1-7
Open AccessUltra-Small and Fabrication-Tolerant Silicon Polarization Beam Splitter Using Sharp Bent Directional Coupler
An ultra-small polarization beam splitter on silicon-on-insulator platform is proposed and demonstrated experimentally employing a sharp bent directional coupler. The coupling length of our device is only 0.764 μ m. High-efficient selective coupling can be achieved benefiting from the inner bend chosen as Through port and ultra-small bend (radii are about 3 μ m) used in Through and Cross waveguides. The measured excess loss is less than 1 dB and extinction ratio is 15–20 dB for TM polarization, meanwhile, the measured excess loss is less than 2 dB and extinction ratio is 15-16 dB for TE polarization in a wavelength range from 1540 nm to 1580 nm. The fabrication tolerance to variation of waveguide width is also demonstrated. When the waveguide widths of the Through and Cross waveguides vary from −24 nm to +12 nm, the measured excess losses remain lower than 2 dB and the extinction ratios are higher than 10 dB for both polarizations. The footprint of the fabricated device is just 1.5 μ m × 1.3 μ m.
- 1 November 2014
- Published by Elsevier in Electrochemistry Communications
- Vol. 48, 111-114
In-situ monitoring of potential enhanced DNA related processes using electrochemical quartz crystal microbalance with dissipation (EQCM-D)
- 1 November 2014
- Published by Elsevier in Electrochemistry Communications
- Vol. 48, 111-114
In-situ monitoring of potential enhanced DNA related processes using electrochemical quartz crystal microbalance with dissipation (EQCM-D)