ISIvan S. Sipatov

Ivan S. Sipatov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ivan S. Sipatov has a total of 56 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Synthesis and Structure of Refractory Multicomponent Alloys

    by I. S. Sipatov, S. A. Petrova, E. V. Ignatieva, S. A. Fedorov, V. A. Bykov, A. A. Rempel

    Many applications in industry require refractory alloys having high mechanical properties and heat resistance at high temperatures. One of the possible alternatives of the existing nowadays materials is the high entropy alloys based on refractory metals like niobium, tantalum, molybdenum and tungsten. So, in present work, the synthesis of four-component Nb25Ta25Mo25W25 and five-component Nb20Ta20Cr20Mo20W20 alloys in an arc furnace was performed and their structure was studied. Energy dispersive chemical analysis demonstrates that the chemical compositions of the alloy Nb25Ta25Mo25W25 corresponds to the nominal one, but Nb20Ta20Cr20Mo20W20 alloy has loss of chromium. It was found that alloys have structure of bcc solid solutions (SS). Both alloys have dendritic structure where the excess of tungsten is in dendrite arms, niobium and molybdenum excess is found in interdendrite regions, while tantalum is randomly distributed in the SS. Chromium in the composition of the system Nb–Ta–Mo–W lead to suppressing of oxides formation according to XRD and EDX data. Coefficients of thermal expansion (CTE) of the NbTaCrMoW and NbTaMoW alloys are smaller than of nickel-based superalloys in a wide temperature range (300–1270 K). Relatively small CTEs of investigated alloys are beneficial for materials used in high-temperature applications.

  • Corrosion Mechanism of High-Entropy DdTbDyHoSc and GdTbDyHoY Alloys

    by M. Yu. Skrylnik, E. Yu. Konysheva, P. V. Kel’, I. S. Sipatov, E. V. Ignatieva, K. Yu. Shunyaev, A. A. Rempel

    This study presents an analysis of the corrosion behavior of two rare-earth equimolar alloys, GdTbDyHoSc and GdTbDyHoY, in a 3% NaCl solution. Electrochemical measurements revealed that both alloys demonstrate increased corrosive activity and a tendency for pitting. Additionally, X-ray diffraction analysis of the corrosion layer formed and microphotographs of the alloys’ surfaces after 24 h of exposure to the 3% NaCl solution are included. These findings lead to conclusions about the nature of the difference in the corrosion behavior of the GdTbDyHoSc and GdTbDyHoY alloys in the 3% NaCl solution.


  • Mechanical Properties of High Entropy Alloys Based on Rare Earth Elements with Yttrium and Scandium

    by I. S. Sipatov, O. A. Korolev, E. V. Ignatieva, L. A. Marshuk, B. R. Gelchinskiy, A. A. Rempel

    —The high-entropy alloys GdTbDyHoSc and GdTbDyHoY having equiatomic composition are considered as promising materials for magnetic cold generators. The results of the alloys structure and chemical composition investigation are presented in this paper. The solidus and liquidus temperatures of the alloys under investigation were determined by the method of differential scanning calorimetry. Based on these data, an experimental mode of thermocyclic treatment was selected. There were no signs of alloys destruction after five cycles testing for heat resistance in the following regime: 15 min exposition at 1073 K (~0.6 of the melting temperature) and subsequent quenching in room temperature water. It was found that the applied heat treatment led to an increase in the hardness of the alloys by 2–3 times and a decrease in wear resistance by 4–40 times, depending on the composition of the alloys and the number of heat treatment cycles. A significant change in the properties of alloys is associated with the formation of oxides of the REM2O3 type not only on the surface of the alloys, but also in their volume, which is due to the high chemical activity of rare earth metals (REM). The presented data will be useful for the development of modes of thermal and thermomechanical processing of various alloys.

  • Mechanical Properties of High Entropy Alloys Based on Rare Earth Elements with Yttrium and Scandium

    by I. S. Sipatov, O. A. Korolev, E. V. Ignatieva, L. A. Marshuk, B. R. Gelchinskiy, A. A. Rempel

    The paper reports the research outcomes on the structural and chemical composition of the equiatomic GdTbDyHoSc and GdTbDyHoY high-entropy alloys, which are potential materials for magnetic cold generators. The solidus and liquidus temperatures of the alloys were determined using differential scanning calorimetry. Based on these findings, an experimental mode of thermal cyclic treatment was selected. No signs of alloy destruction were observed after five test cycles for thermal resistance under exposure at a temperature of 1073 K (~0.6 of the melting point) for 15 minutes followed by quenching in room-temperature water. The applied heat treatment resulted in an increase in the hardness of alloys by 2–3 times and a decrease in wear resistance by 4–40 times depending on the alloy composition and the number of heat treatment cycles. Significant changes in the properties of alloys are associated with the formation of oxides, including REM2О3, not only on the surface but also within their volume, which is due to the high chemical activity of rare-earth metals. The data presented in this study will be beneficial in the development of thermal and thermomechanical treatment methods for studied alloys.


  • Open Access

    Transport Properties of Equiatomic CoCrFeNi High-Entropy Alloy with a Single-Phase Face-Centered Cubic Structure

    by Victor A. Bykov, Tatyana V. Kulikova, Ivan S. Sipatov, Eugene V. Sterkhov, Darya A. Kovalenko, Roman E. Ryltsev

    The key thermophysical properties necessary for the successful design and use of CoCrFeNi alloy in thermophysical applications have been measured experimentally, and the results have been compared with literature values and results previously obtained for commercial Ni-Cr alloys and equiatomic CoCrFeNi alloy. In particular, the thermal diffusivity, coefficient of thermal expansion (CTE), and specific heat capacity were measured for the as-cast and homogenized equiatomic CoCrFeNi alloy over a temperature range allowing the thermal conductivity to be calculated up to 1173 K. The thermal conductivity and thermal diffusivity of the equiatomic CoCrFeNi alloy were found to deviate from monotonic behavior in the temperature range from 773 to 1100 K. Such a deviation was previously observed in the behavior of the temperature dependence of CTE and specific heat capacity of the equiatomic CoCrFeNi alloy. The non-linear behavior is primarily the result of order/disorder phenomena for the as-cast and homogenized sample, as well as non-equilibrium solidification under arc melting conditions for the as-cast sample. The measured data of thermophysical properties are provided for thermally differently treated samples, and it is shown that there is a difference in the behavior of the temperature dependences of CTE, thermal diffusivity, and heat capacity.


  • Open Access

    Transport Properties of Equiatomic CoCrFeNi High-Entropy Alloy with a Single-Phase Face-Centered Cubic Structure

    by Victor Bykov, Tatyana Kulikova, Ivan Sipatov, Eugene Sterkhov, Darya Kovalenko, Roman Ryltsev

    Key thermophysical properties necessary for the successful design and use of CoCrFeNi alloy in thermophysical applications have been measured experimentally, and the results have been compared with literature values and results previously obtained for commercial Ni-Cr alloys and equiatomic CoCrFeNi alloy. In particular, the thermal diffusivity, coefficient of thermal expansion (CTE), and specific heat capacity were measured for the as-cast and homogenized equiatomic CoCrFeNi alloy over a temperature range allowing the thermal conductivity to be calculated up to 1173 K. The thermal conductivity and thermal diffusivity of the equiatomic CoCrFeNi alloy were found to deviate from monotonic behavior in the temperature range from 773 to 1100 K. Such a deviation was previously observed in the behavior of the temperature dependence of CTE and specific heat capacity of the equiatomic CoCrFeNi alloy. The non-linear behavior is primarily the result of order/disorder phenomena for the as-cast and homogenized sample, as well as additionally for the as-cast sample, non-equilibrium solidification under arc melting conditions. The measured data of thermophysical properties are provided for thermally differently treated samples, and it is shown that there is a difference in the behavior of the temperature dependences of CTE, thermal diffusivity, and heat capacity.


  • SYNTHESIS AND STRUCTURE OF FOUR TiZrVNb AND FIVE-COMPONENT TiZrHfVNb REFRACTORY HIGH-ENTROPY ALLOYS

    by I. S. Sipatov, S. А. Petrova, E. V. Ignatieva, A. A. Rempel

    High-entropy alloys attract researcher’s attention due to the presence of a set of new properties. The paper considers the factors affecting the structure of high-entropy alloys (HEAs) based on the elements Ti, Zr, Hf, V, and Nb. The structure data of four-component Ti25Zr25V25Nb25 and five-component Ti20Zr20Hf20V20Nb20 alloys, which were obtained under the same melting and cooling conditions in an arc furnace, are presented. The data of the EDX analysis showed that the chemical composition of the alloys corresponded to the nominal one. Analysis of micrographs of the ingots surface allows us to conclude that the applied melting mode led to overheating of the four–component alloy, but not for the five-component one. It was experimentally found that the primary formation of the four-component alloy occurs faster than that of the five-component one, but further remelting under overheating conditions leads to multiphase structure formation. The maximum content of BCC solid solution (98%) in Ti25Zr25V25Nb25 alloy was achieved during the first remelting, another phase was FCC solid solution (2%). The maximum content of BCC solid solution (95%) in Ti20Zr20Hf20V20Nb20 alloy was obtained by repeated remelting, BCC, HCP solid solutions, and the Laves phase were presented in the amount of 3% or less. The crystal lattice parameters of the BCC main phases for the Ti25Zr25V25Nb25 and Ti20Zr20Hf20V20Nb20 alloys were 3.270 and 3.362 Å, respectively. It was established that to obtain refractory HEAs with a single-phase structure it is important both fulfilment of thermodynamic conditions and correct choice of time-temperature conditions of melting and crystallization for each specific alloy composition.

  • Synthesis and Structure of Four-Component TiZrVNb and Five-Component TiZrHfVNb Refractory High-Entropy Alloys

    by I. S. Sipatov, S. A. Petrova, E. V. Ignatieva, A. A. Rempel

    High-entropy alloys attract the attention of researchers due to a set of new properties. We consider the factors affecting the structure of high-entropy alloys (HEAs) based on elements Ti, Zr, Hf, V, and Nb. The structures of four-component Ti25Zr25V25Nb25 and five-component Ti20Zr20Hf20V20Nb20 alloys fabricated under the same melting and cooling conditions in an arc furnace are studied. Energy dispersive chemical analysis demonstrates that the chemical compositions of the alloys correspond to the nominal ones. Based on an analysis of micrographs of the ingot surfaces, we conclude that the melting conditions lead to overheating of the four-component alloy and do not cause overheating of the five-component. The primary formation of the four-component alloy is found to occur faster than that of the five-component one; however, further remelting under overheating conditions brings about the formation of a multiphase structure. The maximum content of the bcc solid solution (98%) in the Ti25Zr25V25Nb25 alloy is achieved during the first remelting, and another phase (2%) was an fcc solid solution. The maximum content of the bcc solid solution (95%) in the Ti20Zr20Hf20V20Nb20 alloy is achieved during repeated remelting, and bcc and hcp solid solutions and a Laves phase are present in an amount of 3%. The unit cell parameters of the main bcc phases in the Ti25Zr25V25Nb25 and Ti20Zr20Hf20V20Nb20 alloys are 3.270 and 3.362 Å, respectively. The choice of temperature–time conditions of melting and solidification for each specific alloy composition is shown to be important along with the fulfillment of thermodynamic conditions for the production of refractory single-phase HEAs.


  • Structure and hydrogen permeability of V–15Ni alloy

    by A. Baraban, I. Gabis, S. Kozhakhmetov, M. Murzinova, V. Piven, N. Sidorov, I. Sipatov, A. Voyt


  • Influence of Processing Techniques on the Surface Microstructure of V85Ni15 Membrane Alloy

    by I. S. Sipatov, N. I. Sidorov, S. A. Petrova, A. B. Shubin, E. A. Pastukhov, A. V. Fetisov, A. A. Esin, A. A. Vostryakov

    Vanadium-based alloys with a BCC structure are considered to be an alternative to palladium alloys for hydrogen purification. Since the performance of membranes is influenced by not only their bulk...