Natalia Bushueva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Natalia Bushueva has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Yuri Nikolaevich Loginov
Ural Federal University, Ekaterinburg, Russian Federation
3 shared publications - Georgy V. Shimov
Ural Federal University
2 shared publications - A. V. Razinkin
Kamensk-Uralsky Metallurgical Plant, Kamensk-Uralsky, Russian Federation
1 shared publication - Andrey Brodunov
Moscow Witte University
1 shared publication - E. G. Dymshakova
Kamensk Uralsky Metallurgical Works JSC
1 shared publication - Gulmira Nurgazina
Russian State Academy of Intellectual Property
1 shared publication
Latest Publications
- Open Access
- 1 January 2025
- Published by Togliatti State University in Frontier materials & technologies
- No. 3,p. 27-37
Scheme for producing composite material based on structural aluminum alloy by the direct extrusion method
The work covers the development of a technology for producing a bimetallic rod from high-strength 7075 alloy with a cladding layer of 1100 aluminum, which is aimed at improving corrosion resistance while maintaining mechanical properties. A special feature of the proposed technology is the use of an additional front pure aluminum workpiece for the process of direct extrusion of a rod from 7075 alloy. The direct extrusion process for a composite workpiece was simulated with the DEFORM software package’s finite element method. The influence of process temperature and speed on the formation of the cladding layer was analyzed. For this purpose, four problems were formulated with varying heating modes of workpieces and tools. It was found that it is possible to produce a thin cladding layer at a heating temperature of the base 7075 alloy equal to 360 °C and a cladding layer temperature equal to 20 °C, which ensures a uniform distribution of the coating along the length of the rod without signs of delamination. Stress-strain analysis during extrusion showed that a cold additional workpiece ensures continuity for cladding coating formation. However, heating above 300 °C leads to rupture from deformation localization. The developed approach can be used to reduce the cost of products by reducing the consumption of expensive 7075 alloy while simultaneously increasing corrosion resistance due to the use of pure aluminum cladding. Prospects for the development of further research are associated with the optimization of extrusion modes for various rod sizes.
- 1 January 2025
- Published by Togliatti State University in Frontier materials & technologies
- No. 3,p. 27-37
Open AccessScheme for producing composite material based on structural aluminum alloy by the direct extrusion method
The work covers the development of a technology for producing a bimetallic rod from high-strength 7075 alloy with a cladding layer of 1100 aluminum, which is aimed at improving corrosion resistance while maintaining mechanical properties. A special feature of the proposed technology is the use of an additional front pure aluminum workpiece for the process of direct extrusion of a rod from 7075 alloy. The direct extrusion process for a composite workpiece was simulated with the DEFORM software package’s finite element method. The influence of process temperature and speed on the formation of the cladding layer was analyzed. For this purpose, four problems were formulated with varying heating modes of workpieces and tools. It was found that it is possible to produce a thin cladding layer at a heating temperature of the base 7075 alloy equal to 360 °C and a cladding layer temperature equal to 20 °C, which ensures a uniform distribution of the coating along the length of the rod without signs of delamination. Stress-strain analysis during extrusion showed that a cold additional workpiece ensures continuity for cladding coating formation. However, heating above 300 °C leads to rupture from deformation localization. The developed approach can be used to reduce the cost of products by reducing the consumption of expensive 7075 alloy while simultaneously increasing corrosion resistance due to the use of pure aluminum cladding. Prospects for the development of further research are associated with the optimization of extrusion modes for various rod sizes.
- Open Access
- 25 April 2023
- Published by National University of Science and Technology MISiS in Izvestiya Vuzov. Tsvetnaya Metallurgiya (Proceedings of Higher Schools. Nonferrous Metallurgy)
- No. 2,p. 29-37
Structure and strain state of aluminum bars at the initial phase of extrusion
The structure of insufficiently deformed areas at the non-steady phase of extrusion was studied. The tests at Kamensk Uralsky Metallurgical Works using a 120 MN press and 800 mm dia. container, in order to extrude a 355.6 mm dia. Bar was performed. The bar material is the Al–Mg–Si AD33 aluminum alloy (GOST 4784), similar to ASTM 6061. The percentage reduction was 80 %, and the reduction ratio was 5.06. After that, the macrostructure, microstructure, and average grain size along the radius, mechanical properties at room and elevated temperatures were investigated. It was found that the extruded bar macrostructure is fine-grained, homogeneous, and dense, with no nonmetallic or intermetallic inclusions. The cross-section contained several structures. The central part is weakly deformed preserving the dendritic cell structure inherited from the casting. At the circumference, a streaked structure is formed. Its components are crushed and uniformly distributed. We measured the strength at elevated temperatures and compared the results to the data available in the literature. The tested material strength almost doubled, thus indicating its incomplete softening. The ductility was also performed. The DEFORM-2D software, in order to simulate the low reduction of extrusion was used. The metal at the circumference is exposed to a greater strain from the extrusion beginning. A step-by-step analysis indicated that at the first step, the strain is localized near the die hole. In the second step, a rigid area is formed in the vicinity of the die/container liner interface. The circumference layer of metal with a 1.75–2.00 reduction of area is formed. At the bar center, this range is 0.75–1.00 (half of the circumference value). In the third step, the circumference layer with an elevated strain has a wedge-like shape. In the fourth step, the circumference layer (with elevated strain) has an equal thickness along the extrusion axis. This indicates the steady phase. The plastic strain at the bar front end is higher at the circumference than in the center. This confirms the structural analysis results. They show that the central part of the bar may retain its cast structure, while the circumference is deformed. If the bar central part is required to have some specific properties, the bar has to undergo another manufacturing operation to increase the accumulated strain. Re-extrusion processes the areas insufficiently deformed during the first extrusion.
- 25 April 2023
- Published by National University of Science and Technology MISiS in Izvestiya Vuzov. Tsvetnaya Metallurgiya (Proceedings of Higher Schools. Nonferrous Metallurgy)
- No. 2,p. 29-37
Open AccessStructure and strain state of aluminum bars at the initial phase of extrusion
The structure of insufficiently deformed areas at the non-steady phase of extrusion was studied. The tests at Kamensk Uralsky Metallurgical Works using a 120 MN press and 800 mm dia. container, in order to extrude a 355.6 mm dia. Bar was performed. The bar material is the Al–Mg–Si AD33 aluminum alloy (GOST 4784), similar to ASTM 6061. The percentage reduction was 80 %, and the reduction ratio was 5.06. After that, the macrostructure, microstructure, and average grain size along the radius, mechanical properties at room and elevated temperatures were investigated. It was found that the extruded bar macrostructure is fine-grained, homogeneous, and dense, with no nonmetallic or intermetallic inclusions. The cross-section contained several structures. The central part is weakly deformed preserving the dendritic cell structure inherited from the casting. At the circumference, a streaked structure is formed. Its components are crushed and uniformly distributed. We measured the strength at elevated temperatures and compared the results to the data available in the literature. The tested material strength almost doubled, thus indicating its incomplete softening. The ductility was also performed. The DEFORM-2D software, in order to simulate the low reduction of extrusion was used. The metal at the circumference is exposed to a greater strain from the extrusion beginning. A step-by-step analysis indicated that at the first step, the strain is localized near the die hole. In the second step, a rigid area is formed in the vicinity of the die/container liner interface. The circumference layer of metal with a 1.75–2.00 reduction of area is formed. At the bar center, this range is 0.75–1.00 (half of the circumference value). In the third step, the circumference layer with an elevated strain has a wedge-like shape. In the fourth step, the circumference layer (with elevated strain) has an equal thickness along the extrusion axis. This indicates the steady phase. The plastic strain at the bar front end is higher at the circumference than in the center. This confirms the structural analysis results. They show that the central part of the bar may retain its cast structure, while the circumference is deformed. If the bar central part is required to have some specific properties, the bar has to undergo another manufacturing operation to increase the accumulated strain. Re-extrusion processes the areas insufficiently deformed during the first extrusion.
- 5 February 2023
- Published by Springer Nature
- p. 1925-1934
Tax Administration in Transport Sphere in the Digitalization Process
- 5 February 2023
- Published by Springer Nature
- p. 1925-1934
Tax Administration in Transport Sphere in the Digitalization Process
- 1 April 2022
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 24 (2) , 39-49
Deformations in the nonstationary stage of aluminum alloy rod extrusion process with a low elongation ratio
- 1 April 2022
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 24 (2) , 39-49
Deformations in the nonstationary stage of aluminum alloy rod extrusion process with a low elongation ratio