Ali Ozer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ali Ozer has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
- Waltraud M. Kriven
Department of Materials Science and Engineering University of Illinois at Urbana‐Champaign Urbana Illinois USA
8 shared publications - Ebru Şenadım Tüzemen
Sivas Cumhuriyet Üniversitesi
5 shared publications - Ruy Alexandre de Sá Ribeiro
Green Building and Engineering Laboratory National Institute for Amazonian Research Manaus AM Brazil
4 shared publications - Devon M. Samuel
Department of Materials Science and Engineering University of Illinois at Urbana‐Champaign Urbana Illinois USA
3 shared publications - Marilene G. Sa Ribeiro
Green Building and Engineering Laboratory National Institute for Amazonian Research Manaus AM Brazil
3 shared publications - Prapassorn Numkiatsakul
Department of Materials Science and Engineering University of Illinois at Urbana‐Champaign Urbana Illinois USA
3 shared publications
Latest Publications
- 3 November 2026
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 109 (11) , e71326
An Integrated Experimental‐CFD‐RSM‐ANN Investigation of Arsenic Removal From Groundwater by Porous Geopolymer
A novel, low‐cost, porous geopolymer adsorbent incorporating silicon metal powder as a pore‐forming agent and graphene oxide for arsenic (As) removal from aqueous systems was synthesized, characterized, and evaluated. Extensive characterizations were conducted by scanning electronic microscopy (SEM), X‐ray diffraction (XRD), energy‐dispersive X‐ray spectroscopy (EDX), and Fourier transform infrared spectroscopy (FTIR), revealing its performance in a fixed‐bed, adsorption column. XRD and SEM results indicated the formation of geopolymer at 27–29° of 2θ, achieved at a 50 0 C curing temperature with 1wt% silicon metal powder and 1 wt% graphene oxide flakes, forming regular, uniform, interconnected pores. After the preliminary experimental investigations, COMSOL Multiphysics was used to simulate the adsorption process. The model was satisfactorily validated against experimental data, demonstrating its reliability under different operating conditions. The simulations were extended over an inlet concentration (C i ) range of 50–150 ppb, bed height (Z b ) of 2–6 cm, and feed flow rate (Q f ) of 0.005–0.015 L/min. Results showed that increasing Z b and C i , enhanced arsenic removal efficiency (As%) by more than 99% and bed saturation time (t s ) from 4000 to 1200 min, while at higher Q f , both were reduced. Subsequently, response surface methodology (RSM) was employed to optimize operating parameters and understand the main and interaction effects of design factors on As% and t s . ANN‐based predictive modeling was also conducted. Findings of RSM and artificial neural network (ANN) were closely aligned with experimental and computational fluid dynamics (CFD) results, indicating their reliability. Overall, Z b exhibited a profound effect as compared to other factors. This study provides valuable insights for enhancing adsorption efficiency and system scalability.
- 3 November 2026
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 109 (11) , e71326
An Integrated Experimental‐CFD‐RSM‐ANN Investigation of Arsenic Removal From Groundwater by Porous Geopolymer
A novel, low‐cost, porous geopolymer adsorbent incorporating silicon metal powder as a pore‐forming agent and graphene oxide for arsenic (As) removal from aqueous systems was synthesized, characterized, and evaluated. Extensive characterizations were conducted by scanning electronic microscopy (SEM), X‐ray diffraction (XRD), energy‐dispersive X‐ray spectroscopy (EDX), and Fourier transform infrared spectroscopy (FTIR), revealing its performance in a fixed‐bed, adsorption column. XRD and SEM results indicated the formation of geopolymer at 27–29° of 2θ, achieved at a 50 0 C curing temperature with 1wt% silicon metal powder and 1 wt% graphene oxide flakes, forming regular, uniform, interconnected pores. After the preliminary experimental investigations, COMSOL Multiphysics was used to simulate the adsorption process. The model was satisfactorily validated against experimental data, demonstrating its reliability under different operating conditions. The simulations were extended over an inlet concentration (C i ) range of 50–150 ppb, bed height (Z b ) of 2–6 cm, and feed flow rate (Q f ) of 0.005–0.015 L/min. Results showed that increasing Z b and C i , enhanced arsenic removal efficiency (As%) by more than 99% and bed saturation time (t s ) from 4000 to 1200 min, while at higher Q f , both were reduced. Subsequently, response surface methodology (RSM) was employed to optimize operating parameters and understand the main and interaction effects of design factors on As% and t s . ANN‐based predictive modeling was also conducted. Findings of RSM and artificial neural network (ANN) were closely aligned with experimental and computational fluid dynamics (CFD) results, indicating their reliability. Overall, Z b exhibited a profound effect as compared to other factors. This study provides valuable insights for enhancing adsorption efficiency and system scalability.
- 29 June 2026
- Published by Cumhuriyet University in Cumhuriyet Science Journal
- Vol. 47 (3) , 557-565
Structural, Morphological, and Photocatalytic Comparison of TiO₂ Thin Films Deposited by RF Magnetron Sputtering at Room Temperature and 300 °C
In this study, titanium dioxide TiO₂ thin films were deposited onto glass substrates at room temperature and at a substrate temperature of 300°C using the RF magnetron sputtering technique, and their structural, morphological, chemical, and photocatalytic properties were comparatively investigated. XRD analysis revealed that the film deposited at room temperature exhibited a fully amorphous structure, whereas the film deposited at 300°C displayed low-intensity reflections of the anatase (101) and (004) planes on an amorphous background, indicating the onset of limited crystalline nucleation with increasing temperature. Cross-sectional SEM images confirmed the formation of a homogeneous layer with an approximate thickness of 330 nm, while surface SEM micrographs showed a compact and fine-grained morphology characteristic of films deposited at low temperatures. AFM measurements demonstrated a granular surface topography with an RMS roughness of approximately 26 nm over a 10 × 10 µm scan area. FTIR spectra revealed the characteristic Ti–O–Ti vibrational modes, confirming the formation of the TiO₂ network structure. Photocatalytic experiments showed that the TiO₂ film deposited at 300°C achieved approximately 74% degradation of methylene blue under UVA irradiation after about 9 hours, exhibiting significantly higher photocatalytic activity compared to the room-temperature film. This improvement is attributed to partial structural ordering and increased surface roughness. Overall, the findings demonstrate that the structural evolution occurring in TiO₂ thin films deposited at low temperatures directly influences their photocatalytic behavior, and that TiO₂ films exhibiting considerable photocatalytic performance can be produced even at moderate deposition temperatures such as 300°C.
- 29 June 2026
- Published by Cumhuriyet University in Cumhuriyet Science Journal
- Vol. 47 (3) , 557-565
Structural, Morphological, and Photocatalytic Comparison of TiO₂ Thin Films Deposited by RF Magnetron Sputtering at Room Temperature and 300 °C
In this study, titanium dioxide TiO₂ thin films were deposited onto glass substrates at room temperature and at a substrate temperature of 300°C using the RF magnetron sputtering technique, and their structural, morphological, chemical, and photocatalytic properties were comparatively investigated. XRD analysis revealed that the film deposited at room temperature exhibited a fully amorphous structure, whereas the film deposited at 300°C displayed low-intensity reflections of the anatase (101) and (004) planes on an amorphous background, indicating the onset of limited crystalline nucleation with increasing temperature. Cross-sectional SEM images confirmed the formation of a homogeneous layer with an approximate thickness of 330 nm, while surface SEM micrographs showed a compact and fine-grained morphology characteristic of films deposited at low temperatures. AFM measurements demonstrated a granular surface topography with an RMS roughness of approximately 26 nm over a 10 × 10 µm scan area. FTIR spectra revealed the characteristic Ti–O–Ti vibrational modes, confirming the formation of the TiO₂ network structure. Photocatalytic experiments showed that the TiO₂ film deposited at 300°C achieved approximately 74% degradation of methylene blue under UVA irradiation after about 9 hours, exhibiting significantly higher photocatalytic activity compared to the room-temperature film. This improvement is attributed to partial structural ordering and increased surface roughness. Overall, the findings demonstrate that the structural evolution occurring in TiO₂ thin films deposited at low temperatures directly influences their photocatalytic behavior, and that TiO₂ films exhibiting considerable photocatalytic performance can be produced even at moderate deposition temperatures such as 300°C.
- 27 February 2026
- Published by Cumhuriyet University in Cumhuriyet Science Journal
- Vol. 47 (1) , 119-127
Investigation of Structural and Photocatalytic Properties of ZnO Thin Films
This study focuses on the fabrication of immobilized and stable pure ZnO thin films via RF magnetron sputtering to eliminate the drawbacks of powder-based photocatalysts, such as catalyst recovery, filtration difficulties, and secondary pollution risks. While the photocatalytic potential of ZnO is well established, research investigating the structural origins of performance enhancement in undoped ZnO thin films achieved through physical vapor deposition (PVD) parameters and post-deposition annealing remains limited. In this context, the contribution of this work lies in the quantitative demonstration of the enhancement in photocatalytic performance induced by annealing at 400 °C in additive-free ZnO thin films. As-deposited and 400 °C annealed ZnO thin films were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and energy-dispersive X-ray spectroscopy (EDX). XRD analysis confirmed a hexagonal wurtzite structure for both films, while post-deposition annealing improved crystalline quality and increased the average crystallite size from 53.3 nm to 57.2 nm. AFM measurements revealed an increase in surface roughness from 1.252 nm to 12.14 nm after annealing. Photocatalytic degradation experiments of methylene blue (MB) were conducted under UV-A irradiation, and concentration changes were monitored by UV–Vis spectroscopy. The as-deposited ZnO thin films exhibited only 11% degradation efficiency after 8 hours, whereas the films annealed at 400 °C achieved 68% degradation after 11 hours, corresponding to a sevenfold enhancement in photocatalytic performance. These results demonstrate that post-deposition annealing is an effective strategy for optimizing the photocatalytic activity of pure ZnO thin films under low-energy UV-A light.
- 27 February 2026
- Published by Cumhuriyet University in Cumhuriyet Science Journal
- Vol. 47 (1) , 119-127
Investigation of Structural and Photocatalytic Properties of ZnO Thin Films
This study focuses on the fabrication of immobilized and stable pure ZnO thin films via RF magnetron sputtering to eliminate the drawbacks of powder-based photocatalysts, such as catalyst recovery, filtration difficulties, and secondary pollution risks. While the photocatalytic potential of ZnO is well established, research investigating the structural origins of performance enhancement in undoped ZnO thin films achieved through physical vapor deposition (PVD) parameters and post-deposition annealing remains limited. In this context, the contribution of this work lies in the quantitative demonstration of the enhancement in photocatalytic performance induced by annealing at 400 °C in additive-free ZnO thin films. As-deposited and 400 °C annealed ZnO thin films were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and energy-dispersive X-ray spectroscopy (EDX). XRD analysis confirmed a hexagonal wurtzite structure for both films, while post-deposition annealing improved crystalline quality and increased the average crystallite size from 53.3 nm to 57.2 nm. AFM measurements revealed an increase in surface roughness from 1.252 nm to 12.14 nm after annealing. Photocatalytic degradation experiments of methylene blue (MB) were conducted under UV-A irradiation, and concentration changes were monitored by UV–Vis spectroscopy. The as-deposited ZnO thin films exhibited only 11% degradation efficiency after 8 hours, whereas the films annealed at 400 °C achieved 68% degradation after 11 hours, corresponding to a sevenfold enhancement in photocatalytic performance. These results demonstrate that post-deposition annealing is an effective strategy for optimizing the photocatalytic activity of pure ZnO thin films under low-energy UV-A light.
- Open Access
- 30 July 2025
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 22 (6)
Strength and thermal stability of enhanced metakaolin‐based geopolymer composites with sand and fibers
The growing demand for sustainable materials in construction and ceramics has driven interest in geopolymer technology as an eco‐friendly alternative to traditional cement‐based systems. Geopolymers, synthesized from aluminosilicate precursors like metakaolin, offer high mechanical performance, chemical resistance, and lower carbon footprints. This study presents the development of innovative metakaolin‐based geopolymer composites reinforced with natural mineral particles and fibers to enhance mechanical and functional properties while maintaining environmental sustainability. A tailored formulation combining commercial metakaolin, optimized waterglass, and a hybrid reinforcement strategy was employed. Three compositions were evaluated: (1) 20 wt.% ball‐milled fine sand and 40 wt.% Prairie fine sand (B20P40); (2) B20P40 with 5 wt.% basalt fibers (B20P40Bas5); and (3) B20P40 with 5 wt.% bamboo fibers (B20P40Bam5). The composites demonstrated flexural strengths of 12.1, 17.1, and 14.6 MPa, respectively, with corresponding apparent densities of 1.93, 1.88, and 1.81 g/cm 3 . Incorporation of natural fibers improved strength, ductility, and thermal stability, while reducing density, water absorption, and pore volume. The results indicate that these fiber‐reinforced geopolymer composites are promising candidates for sustainable construction and ceramic applications, offering a viable path toward high‐performance, low‐impact building materials.
- 30 July 2025
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 22 (6)
Open AccessStrength and thermal stability of enhanced metakaolin‐based geopolymer composites with sand and fibers
The growing demand for sustainable materials in construction and ceramics has driven interest in geopolymer technology as an eco‐friendly alternative to traditional cement‐based systems. Geopolymers, synthesized from aluminosilicate precursors like metakaolin, offer high mechanical performance, chemical resistance, and lower carbon footprints. This study presents the development of innovative metakaolin‐based geopolymer composites reinforced with natural mineral particles and fibers to enhance mechanical and functional properties while maintaining environmental sustainability. A tailored formulation combining commercial metakaolin, optimized waterglass, and a hybrid reinforcement strategy was employed. Three compositions were evaluated: (1) 20 wt.% ball‐milled fine sand and 40 wt.% Prairie fine sand (B20P40); (2) B20P40 with 5 wt.% basalt fibers (B20P40Bas5); and (3) B20P40 with 5 wt.% bamboo fibers (B20P40Bam5). The composites demonstrated flexural strengths of 12.1, 17.1, and 14.6 MPa, respectively, with corresponding apparent densities of 1.93, 1.88, and 1.81 g/cm 3 . Incorporation of natural fibers improved strength, ductility, and thermal stability, while reducing density, water absorption, and pore volume. The results indicate that these fiber‐reinforced geopolymer composites are promising candidates for sustainable construction and ceramic applications, offering a viable path toward high‐performance, low‐impact building materials.
- Open Access
- 26 May 2025
- Published by Springer Nature in Journal of the Australian Ceramic Society
- Vol. 61 (5) , 1837-1851
The effect of cupola furnace iron slag on the physical and mechanical properties of alkali-activated fly ash-based mortars
This study investigates the physical and mechanical properties of alkali-activated mortars, in which thermal power plant fly ash (FA) was partially replaced by cupola furnace iron slag (IS). An optimal mix design determined through preliminary tests consisted of an aggregate-to-binder ratio of 1.5 (by weight), NaOH solution concentration of 10 M, Na₂SiO₃ (liquid) to NaOH (solid) ratio of 2, and a water-to-binder ratio of 0.3, all maintained consistently across mixtures. Chemical compositions and phase structures of raw materials were characterized using X-ray fluorescence (XRF) and X-ray diffraction (XRD), respectively. Particle size distribution was determined by laser diffraction analysis, and microstructural morphology was examined using scanning electron microscopy (SEM). Bulk density and apparent porosity were measured using Archimedes’ method with water as the immersion medium. Mechanical properties were evaluated through compressive strength and three-point bending tests after 28 days of curing. Results showed that mortars incorporating 75 wt% cupola furnace iron slag as a fly ash replacement exhibited superior performance, achieving a bulk density of 2118 kg/m³, apparent porosity of 12.2%, compressive strength of 44 MPa, and flexural strength of 10.2 MPa. These findings highlight the potential of iron slag as an effective supplementary material in alkali-activated mortars, enhancing mechanical properties and contributing to microstructural densification.
- 26 May 2025
- Published by Springer Nature in Journal of the Australian Ceramic Society
- Vol. 61 (5) , 1837-1851
Open AccessThe effect of cupola furnace iron slag on the physical and mechanical properties of alkali-activated fly ash-based mortars
This study investigates the physical and mechanical properties of alkali-activated mortars, in which thermal power plant fly ash (FA) was partially replaced by cupola furnace iron slag (IS). An optimal mix design determined through preliminary tests consisted of an aggregate-to-binder ratio of 1.5 (by weight), NaOH solution concentration of 10 M, Na₂SiO₃ (liquid) to NaOH (solid) ratio of 2, and a water-to-binder ratio of 0.3, all maintained consistently across mixtures. Chemical compositions and phase structures of raw materials were characterized using X-ray fluorescence (XRF) and X-ray diffraction (XRD), respectively. Particle size distribution was determined by laser diffraction analysis, and microstructural morphology was examined using scanning electron microscopy (SEM). Bulk density and apparent porosity were measured using Archimedes’ method with water as the immersion medium. Mechanical properties were evaluated through compressive strength and three-point bending tests after 28 days of curing. Results showed that mortars incorporating 75 wt% cupola furnace iron slag as a fly ash replacement exhibited superior performance, achieving a bulk density of 2118 kg/m³, apparent porosity of 12.2%, compressive strength of 44 MPa, and flexural strength of 10.2 MPa. These findings highlight the potential of iron slag as an effective supplementary material in alkali-activated mortars, enhancing mechanical properties and contributing to microstructural densification.
- Open Access
- 3 May 2025
- Published by Springer Nature in Materials and Structures
- Vol. 58 (4) , 1-20
Metakaolin-based geopolymer matrix formulations for higher strength and thermal stability
The need for sustainable and high-performance construction materials has led to the development of novel geopolymer matrices. This project aims to create an optimized, highly reactive, metakaolin-based geopolymer matrix for sustainable construction materials. The study involved mixing and optimizing commercial alkali silicates and metakaolin to enhance strength, stability, and durability. The goal was to maximize the flexural strength of the geopolymer matrix using one type of commercial metakaolin (MK), seven commercial waterglass formulations with varying water content, and a single, low-energy geopolymer processing method. The findings show that geopolymer matrices with charge-balancing potassium ions and 11 mol of water, and two formulations with charge-balancing sodium ions and 13 mol of water, resulted in the highest strengths (5.9–7.7–8.1 MPa on average), lower porosity, and reduced thermal degradation. These findings have practical applications in reducing the environmental impact of traditional construction materials. By utilizing metakaolin and commercial alkali silicates, the research enhances the mechanical properties of the geopolymer and promotes the use of industrial by-products. The low-energy processing method aligns with sustainability principles by minimizing energy consumption. The resulting geopolymer composites exhibit superior strength, durability, and thermal resistance, making them suitable for sustainable ceramics and construction materials. This research contributes to the development of eco-friendly construction solutions, promoting a sustainable and resilient built environment. Its significance lies in its holistic approach to optimizing geopolymer matrices for enhanced performance and sustainability.
- 3 May 2025
- Published by Springer Nature in Materials and Structures
- Vol. 58 (4) , 1-20
Open AccessMetakaolin-based geopolymer matrix formulations for higher strength and thermal stability
The need for sustainable and high-performance construction materials has led to the development of novel geopolymer matrices. This project aims to create an optimized, highly reactive, metakaolin-based geopolymer matrix for sustainable construction materials. The study involved mixing and optimizing commercial alkali silicates and metakaolin to enhance strength, stability, and durability. The goal was to maximize the flexural strength of the geopolymer matrix using one type of commercial metakaolin (MK), seven commercial waterglass formulations with varying water content, and a single, low-energy geopolymer processing method. The findings show that geopolymer matrices with charge-balancing potassium ions and 11 mol of water, and two formulations with charge-balancing sodium ions and 13 mol of water, resulted in the highest strengths (5.9–7.7–8.1 MPa on average), lower porosity, and reduced thermal degradation. These findings have practical applications in reducing the environmental impact of traditional construction materials. By utilizing metakaolin and commercial alkali silicates, the research enhances the mechanical properties of the geopolymer and promotes the use of industrial by-products. The low-energy processing method aligns with sustainability principles by minimizing energy consumption. The resulting geopolymer composites exhibit superior strength, durability, and thermal resistance, making them suitable for sustainable ceramics and construction materials. This research contributes to the development of eco-friendly construction solutions, promoting a sustainable and resilient built environment. Its significance lies in its holistic approach to optimizing geopolymer matrices for enhanced performance and sustainability.
- Open Access
- 29 April 2025
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 22 (5)
Metakaolin‐based geopolymer mineral particulate composite design for higher strength and thermal stability
This research targets to produce new composites from a highly reactive metakaolin‐based geopolymer matrix reinforced with natural particles for use in sustainable ceramics, building and construction. Commercial waterglass and added mineral particles were optimized for geopolymer composites to provide higher strength, stability, and durability. The design method implicated higher flexural strength of one type of commercial metakaolin, one commercial waterglass formulation, a single‐low‐energy geopolymer processing, and seven types of added mineral particles. The particulate reinforcement formulations added to the geopolymer matrix were: (1) 20 wt% chamotte and 40 wt% Prairie fine sand; (2) 20 wt% chamotte and 40 wt% Quikrete medium sand; (3) 20 wt% chamotte and 40 wt% Quikrete fine sand; (4) 20 wt% ball‐milled fine sand; (5) 20 wt% ball‐milled fine sand and 40 wt% Quikrete fine sand; (6) 20 wt% ball‐milled fine sand and 40 wt% Prairie fine sand; (7) 10 wt% ball‐milled fine sand and 50 wt% Prairie fine sand. Potassium metasilicate Kasolv 16 with 11 M of water, Metamax metakaolin, reinforced with 20 wt% ball‐milled fine sand, and 40 wt% Prairie fine sand (BF20PF40) resulted in the highest strength geopolymer composite. BF20PF40 also yielded lower mass loss, higher packing density, and better thermal stability.
- 29 April 2025
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 22 (5)
Open AccessMetakaolin‐based geopolymer mineral particulate composite design for higher strength and thermal stability
This research targets to produce new composites from a highly reactive metakaolin‐based geopolymer matrix reinforced with natural particles for use in sustainable ceramics, building and construction. Commercial waterglass and added mineral particles were optimized for geopolymer composites to provide higher strength, stability, and durability. The design method implicated higher flexural strength of one type of commercial metakaolin, one commercial waterglass formulation, a single‐low‐energy geopolymer processing, and seven types of added mineral particles. The particulate reinforcement formulations added to the geopolymer matrix were: (1) 20 wt% chamotte and 40 wt% Prairie fine sand; (2) 20 wt% chamotte and 40 wt% Quikrete medium sand; (3) 20 wt% chamotte and 40 wt% Quikrete fine sand; (4) 20 wt% ball‐milled fine sand; (5) 20 wt% ball‐milled fine sand and 40 wt% Quikrete fine sand; (6) 20 wt% ball‐milled fine sand and 40 wt% Prairie fine sand; (7) 10 wt% ball‐milled fine sand and 50 wt% Prairie fine sand. Potassium metasilicate Kasolv 16 with 11 M of water, Metamax metakaolin, reinforced with 20 wt% ball‐milled fine sand, and 40 wt% Prairie fine sand (BF20PF40) resulted in the highest strength geopolymer composite. BF20PF40 also yielded lower mass loss, higher packing density, and better thermal stability.
- Open Access
- 31 March 2025
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 218
Novel geopolymer materials for fast and thermal neutron shielding
- 31 March 2025
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 218
Open AccessNovel geopolymer materials for fast and thermal neutron shielding
- Open Access
- 28 October 2024
- Published by Elsevier in Ceramics International
- Vol. 51 (1) , 25-42
Irreversible, in situ, self-healing and self-glazing of geopolymers
- 28 October 2024
- Published by Elsevier in Ceramics International
- Vol. 51 (1) , 25-42
Open AccessIrreversible, in situ, self-healing and self-glazing of geopolymers
- Open Access
- 23 May 2024
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 107 (9) , 6045-6059
Optimizing the design parameters for chamotte particle‐reinforced geopolymers
This study delved into the utilization of chamotte particles in varying contents (0–50 wt%) as reinforcing agents in both fresh and hardened states within potassium‐based geopolymer (KGP) composites. Although the previous research predominantly underscored the high‐temperature stability of chamotte in composites subjected to extreme conditions, this study focuses on expanding their potential applications at ambient temperature. The experimental findings showed that the flowability of the pastes experienced a slight reduction up to 20 wt% chamotte, followed by a substantial decrease, ultimately resulting in complete shape retention at 50 wt%. Squeeze flow and standard rheological tests supported these observations, revealing elevated work‐to‐squeeze values peaking at 1.3 J. X‐ray diffraction data showed that crystallinity prevailed in chamotte, establishing its efficacy as a nonreactive reinforcement. In the hardened state, the inclusion of chamotte enhanced the mechanical properties of the composites, specifically compressive, flexural, and splitting tensile strengths, reaching up to 61.7, 13.2, and 5.6 MPa, respectively. Young's modulus ( E ) and shear modulus ( G ) also exhibited an upward trend with increasing chamotte content, reaching values of up to 17.7 and 7.7 GPa at 50 wt%, respectively. Scanning electron microscopy (SEM) analysis validated particle interlocking and crack‐bridging mechanisms. In general, this study highlights the effectiveness of chamotte particles in improving the mechanical properties of KGP composites at room temperature. It also emphasizes the necessity of considering the mentioned parameters in the design of particulate‐reinforced geopolymer compositions for diverse applications.
- 23 May 2024
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 107 (9) , 6045-6059
Open AccessOptimizing the design parameters for chamotte particle‐reinforced geopolymers
This study delved into the utilization of chamotte particles in varying contents (0–50 wt%) as reinforcing agents in both fresh and hardened states within potassium‐based geopolymer (KGP) composites. Although the previous research predominantly underscored the high‐temperature stability of chamotte in composites subjected to extreme conditions, this study focuses on expanding their potential applications at ambient temperature. The experimental findings showed that the flowability of the pastes experienced a slight reduction up to 20 wt% chamotte, followed by a substantial decrease, ultimately resulting in complete shape retention at 50 wt%. Squeeze flow and standard rheological tests supported these observations, revealing elevated work‐to‐squeeze values peaking at 1.3 J. X‐ray diffraction data showed that crystallinity prevailed in chamotte, establishing its efficacy as a nonreactive reinforcement. In the hardened state, the inclusion of chamotte enhanced the mechanical properties of the composites, specifically compressive, flexural, and splitting tensile strengths, reaching up to 61.7, 13.2, and 5.6 MPa, respectively. Young's modulus ( E ) and shear modulus ( G ) also exhibited an upward trend with increasing chamotte content, reaching values of up to 17.7 and 7.7 GPa at 50 wt%, respectively. Scanning electron microscopy (SEM) analysis validated particle interlocking and crack‐bridging mechanisms. In general, this study highlights the effectiveness of chamotte particles in improving the mechanical properties of KGP composites at room temperature. It also emphasizes the necessity of considering the mentioned parameters in the design of particulate‐reinforced geopolymer compositions for diverse applications.