Haydn N. G. Wadley
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Haydn N. G. Wadley has a total of 71 co-authors. Here are the top co-authors by number of shared publications:
- Vikram Sudhir Deshpande
Department of Engineering, University of Cambridge
5 shared publications X. W. Zhou
Department of Materials Science and Engineering , School of Engineering and Applied Science, University of Virginia , Charlottesville, Virginia 22903, USA
4 shared publicationsD. D. Hass
University of Virginia
3 shared publicationsHengbei Zhao
University of Virginia Department of Materials Science and Engineering 395 McCormick Rd., P.O. Box 400745, Charlottesville, Virginia 22904
3 shared publications- Jeroen A. Deijkers
Department of Materials Science and Engineering University of Virginia Charlottesville VA USA
3 shared publications - David R. Clarke
Harvard John A. Paulson School of Engineering and Applied Sciences, Harvard University, Cambridge, USA
2 shared publications
Latest Publications
- 11 September 2026
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 47 (2)
Infrared absorption of lanthanide disilicate environmental barrier coating materials
- 11 September 2026
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 47 (2)
Infrared absorption of lanthanide disilicate environmental barrier coating materials
- Open Access
- 26 February 2026
- Published by Open Engineering Inc in engrXiv
Laboratory X-ray Diffraction Based Instrument for Full field Stress-Strain Measurements in Metals
Development of constitutive laws for elastic–plastic materials traditionally require hundreds of mechanical tests on statically determinate specimens to map their yield surface. Although accurate, this approach is slow and limits the pace of materials discovery, especially as modern alloy design and manufacturing accelerate while mechanical testing remains low throughput. Advanced processes such as additive manufacturing further complicate testing by producing non-uniform stress states even in nominally determinate specimens, making local mechanical response measurements essential, particularly under complex stress state incurred in most engineering applications. Digital Image Correlation (DIC) provides full-field total strain measurements and is valuable for elastic characterisation, but it cannot capture the plastic deformation fields needed to resolve history-dependent plasticity. In other words, understanding plastic behaviour requires access to an internal (history) variable beyond total strain. In this work, we address this longstanding gap by introducing a new laboratory instrument based on Energy-Dispersive X-ray Diffraction (EDXRD) that enables full field measurement of elastic strain field concurrently with DIC based full field strains to regularize the problem of constitutive modelling in metals. Consequently, we can extract local stress-strain responses along diverse loading paths (multi-axial stress states) within a single specimen, yielding dozens of independent measurements from a single test. This capability opens the door to using complex specimens (statically indeterminate) that intentionally generate a wide range of strain paths, allowing the yield surface and its evolution to be characterised from only a few experiments
- 26 February 2026
- Published by Open Engineering Inc in engrXiv
Open AccessLaboratory X-ray Diffraction Based Instrument for Full field Stress-Strain Measurements in Metals
Development of constitutive laws for elastic–plastic materials traditionally require hundreds of mechanical tests on statically determinate specimens to map their yield surface. Although accurate, this approach is slow and limits the pace of materials discovery, especially as modern alloy design and manufacturing accelerate while mechanical testing remains low throughput. Advanced processes such as additive manufacturing further complicate testing by producing non-uniform stress states even in nominally determinate specimens, making local mechanical response measurements essential, particularly under complex stress state incurred in most engineering applications. Digital Image Correlation (DIC) provides full-field total strain measurements and is valuable for elastic characterisation, but it cannot capture the plastic deformation fields needed to resolve history-dependent plasticity. In other words, understanding plastic behaviour requires access to an internal (history) variable beyond total strain. In this work, we address this longstanding gap by introducing a new laboratory instrument based on Energy-Dispersive X-ray Diffraction (EDXRD) that enables full field measurement of elastic strain field concurrently with DIC based full field strains to regularize the problem of constitutive modelling in metals. Consequently, we can extract local stress-strain responses along diverse loading paths (multi-axial stress states) within a single specimen, yielding dozens of independent measurements from a single test. This capability opens the door to using complex specimens (statically indeterminate) that intentionally generate a wide range of strain paths, allowing the yield surface and its evolution to be characterised from only a few experiments
- Open Access
- 17 December 2025
- Published by Elsevier in Materials & Design
- Vol. 261
Accelerating materials discovery in heterogeneous composition-property design spaces via collaborative Bayesian optimization
- 17 December 2025
- Published by Elsevier in Materials & Design
- Vol. 261
Open AccessAccelerating materials discovery in heterogeneous composition-property design spaces via collaborative Bayesian optimization
- Open Access
- 27 November 2025
- Published by Elsevier in Materials & Design
- Vol. 260
Optical absorption of lanthanide disilicate environmental barrier coating materials
- 27 November 2025
- Published by Elsevier in Materials & Design
- Vol. 260
Open AccessOptical absorption of lanthanide disilicate environmental barrier coating materials
- 6 February 2025
- Published by Elsevier in Acta Materialia
- Vol. 287
Two doping strategies for modifying radiative transport in ZrO2-YTaO4 thermal barrier coating materials
- 6 February 2025
- Published by Elsevier in Acta Materialia
- Vol. 287
Two doping strategies for modifying radiative transport in ZrO2-YTaO4 thermal barrier coating materials
- 1 April 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (4)
A high temperature engine materials test facility
Gas turbine engines subject materials to extreme conditions. Their high temperature materials and co-developed coatings must survive combustion gas temperatures currently approaching 1800 °C, large thermal gradients, severe thermal shock, and static and fatigue inducing applied stresses, all the while operating in highly reactive, high-pressure, high-speed combustion gas flows containing significant partial pressures of water vapor, oxygen, and other reactive species for many tens of thousands of hours. We describe the design and development of a test facility for the study of materials under individual and combinations of test parameters similar to those experienced within legacy and future engines. A hydraulic load frame capable of applying static or cyclic tension-compression stresses up to 400 MPa to flat-dog bone-shaped test specimens is integrated within an environmental test chamber capable of sustaining gas pressures from 0.1 to 1.2 MPa (1–12 atm). An adjustable 0.1–2 kW power CO2 laser whose 10.6 µm wavelength radiation is strongly absorbed by ceramic coating materials is used to heat sample surfaces to temperatures of 1800 °C and above, while rear surface air jet cooling establishes through-thickness thermal gradients. Rapid laser heating in conjunction with transiently applied front and/or rear-side air cooling is used to create hot or cold thermal shock effects. This is accompanied by the impingement of a high pressure (up to 1.3 MPa) reactive gas jet upon the sample with speeds up to 300 m/s by preheating dry air, mixing it with steam to the desired humidity, heating to 850 °C, and then expanding it through a converging nozzle. Thermal imaging pyrometers measure specimen front and back surface temperature fields, while environmental test chamber view ports permit digital image correlation and strain mapping.
- 1 April 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (4)
A high temperature engine materials test facility
Gas turbine engines subject materials to extreme conditions. Their high temperature materials and co-developed coatings must survive combustion gas temperatures currently approaching 1800 °C, large thermal gradients, severe thermal shock, and static and fatigue inducing applied stresses, all the while operating in highly reactive, high-pressure, high-speed combustion gas flows containing significant partial pressures of water vapor, oxygen, and other reactive species for many tens of thousands of hours. We describe the design and development of a test facility for the study of materials under individual and combinations of test parameters similar to those experienced within legacy and future engines. A hydraulic load frame capable of applying static or cyclic tension-compression stresses up to 400 MPa to flat-dog bone-shaped test specimens is integrated within an environmental test chamber capable of sustaining gas pressures from 0.1 to 1.2 MPa (1–12 atm). An adjustable 0.1–2 kW power CO2 laser whose 10.6 µm wavelength radiation is strongly absorbed by ceramic coating materials is used to heat sample surfaces to temperatures of 1800 °C and above, while rear surface air jet cooling establishes through-thickness thermal gradients. Rapid laser heating in conjunction with transiently applied front and/or rear-side air cooling is used to create hot or cold thermal shock effects. This is accompanied by the impingement of a high pressure (up to 1.3 MPa) reactive gas jet upon the sample with speeds up to 300 m/s by preheating dry air, mixing it with steam to the desired humidity, heating to 850 °C, and then expanding it through a converging nozzle. Thermal imaging pyrometers measure specimen front and back surface temperature fields, while environmental test chamber view ports permit digital image correlation and strain mapping.
- Open Access
- 6 June 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 41 (4)
Noise reduction and peak detection in x-ray diffraction data by linear and nonlinear methods
Considerable progress has been made in the last few years in removing white noise from visible–near-ultraviolet (UV/VIS) spectra while leaving information intact. For x-ray diffraction, the challenges are different: detecting and locating peaks rather than line shape analysis. Here, we investigate possibilities of state-of-the-art UV/VIS methods for noise reduction, peak detection, and peak location applied to x-ray diffraction data, in this case, data for a ZrO2 −33 mol. % TaO4 ceramic. The same advantages seen in UV/VIS spectroscopy are found here as well.
- 6 June 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 41 (4)
Open AccessNoise reduction and peak detection in x-ray diffraction data by linear and nonlinear methods
Considerable progress has been made in the last few years in removing white noise from visible–near-ultraviolet (UV/VIS) spectra while leaving information intact. For x-ray diffraction, the challenges are different: detecting and locating peaks rather than line shape analysis. Here, we investigate possibilities of state-of-the-art UV/VIS methods for noise reduction, peak detection, and peak location applied to x-ray diffraction data, in this case, data for a ZrO2 −33 mol. % TaO4 ceramic. The same advantages seen in UV/VIS spectroscopy are found here as well.
- Open Access
- 1 September 2022
- Published by AIP Publishing in AIP Advances
- Vol. 12 (9) , 095021
The small-scale limits of electron beam melt additive manufactured Ti–6Al–4V octet-truss lattices
The emergence of powder-based additive manufacturing (AM) processes, such as electron beam melting (EBM), enables the one step manufacture of microarchitected metamaterials from topology optimized models. However, many applications are optimized by low relative density lattices with slender trusses whose diameter approaches small multiples of largest powder particles, potentially resulting in surface roughness. The thermal history experienced by alloy powders also modifies the alloy microstructure, and thus mechanical behavior, posing a significant challenge to metallic metamaterial designs and fabrication. We therefore build and characterize the multiscale structure and mechanical properties of EBM manufactured Ti–6Al–4V octet truss lattices with strut diameters approaching the particle diameter-imposed fabrication limit. We measure the dependence of their relative density, elastic modulus, and compressive strength on the fabrication process-controlled truss topology and microstructure, and compare them to identical smooth surface structures made from an annealed, wrought version of the same alloy built using a snap-fit assembly method. Micro-x-ray tomography confirmed that the lattice strut surfaces were covered with partially melted powder particles, resulting in about 29% of the lattice mass that inefficiently supported the applied loads. The use of a powder bed held at a temperature of 600–700 °C also resulted in a lamellar α/β phase microstructure with an elastic modulus, yield strength, and a ductility that were less than the equiaxed α/β microstructure of snap-fit assembled structures. However, the higher tangent modulus of the lamellar AM processed alloy resulted in significant strengthening of EBM lattices that failed by inelastic buckling during compression. The ability to increase the alloy tangent modulus during an EBM build process therefore provides a promising approach for increasing lattice compressive strength and therefore compensates for surface roughness induced losses.
- 1 September 2022
- Published by AIP Publishing in AIP Advances
- Vol. 12 (9) , 095021
Open AccessThe small-scale limits of electron beam melt additive manufactured Ti–6Al–4V octet-truss lattices
The emergence of powder-based additive manufacturing (AM) processes, such as electron beam melting (EBM), enables the one step manufacture of microarchitected metamaterials from topology optimized models. However, many applications are optimized by low relative density lattices with slender trusses whose diameter approaches small multiples of largest powder particles, potentially resulting in surface roughness. The thermal history experienced by alloy powders also modifies the alloy microstructure, and thus mechanical behavior, posing a significant challenge to metallic metamaterial designs and fabrication. We therefore build and characterize the multiscale structure and mechanical properties of EBM manufactured Ti–6Al–4V octet truss lattices with strut diameters approaching the particle diameter-imposed fabrication limit. We measure the dependence of their relative density, elastic modulus, and compressive strength on the fabrication process-controlled truss topology and microstructure, and compare them to identical smooth surface structures made from an annealed, wrought version of the same alloy built using a snap-fit assembly method. Micro-x-ray tomography confirmed that the lattice strut surfaces were covered with partially melted powder particles, resulting in about 29% of the lattice mass that inefficiently supported the applied loads. The use of a powder bed held at a temperature of 600–700 °C also resulted in a lamellar α/β phase microstructure with an elastic modulus, yield strength, and a ductility that were less than the equiaxed α/β microstructure of snap-fit assembled structures. However, the higher tangent modulus of the lamellar AM processed alloy resulted in significant strengthening of EBM lattices that failed by inelastic buckling during compression. The ability to increase the alloy tangent modulus during an EBM build process therefore provides a promising approach for increasing lattice compressive strength and therefore compensates for surface roughness induced losses.
- 3 May 2019
- Published by ASME International in Journal of Thermal Science and Engineering Applications
- Vol. 11 (6) , 1-40
Heat Pipe Thermal Management at Hypersonic Vehicle Leading Edges: A Low-Temperature Model Study
The intense thermal fluxes and aero-thermomechanical loads generated at sharp leading edges of atmospheric hypersonic vehicles traveling above Mach 5 have motivated an interest in novel thermal management strategies. Here, we use a low-temperature stainless steel-water system to experimentally investigate the feasibility of metallic leading edge heat pipe concepts for thermal management in an efficient load supporting structure. The concept is based upon a two-phase, high thermal conductance “heat pipe” which redistributes the localized thermal flux created at the leading edge stagnation point over a larger surface for effective removal. Structural efficiency is achieved by configuring the system as a wedge-shaped sandwich panel with an I-cell core that simultaneously permits axial vapor and returns liquid flow. The measured axial temperature profiles resulting from a localized thermal flux applied to the tip are consistent with effective thermal spreading that lowered the peak leading edge temperature and reduced the temperature gradients when compared with an equivalent structure containing no working fluid. A simple finite element model that treated the vapor as an equivalent, high thermal conductivity material was in good agreement with these experiments. The model is then used to design a niobium alloy-lithium system that is shown to be suitable for enthalpy conditions representative of Mach 7 scramjet-powered flight. The study indicates that the surface temperature reductions of heat pipe-based leading edges may be sufficient to permit the use of nonablative, refractory metal leading edges with oxidation protection in hypersonic environments.
- 3 May 2019
- Published by ASME International in Journal of Thermal Science and Engineering Applications
- Vol. 11 (6) , 1-40
Heat Pipe Thermal Management at Hypersonic Vehicle Leading Edges: A Low-Temperature Model Study
The intense thermal fluxes and aero-thermomechanical loads generated at sharp leading edges of atmospheric hypersonic vehicles traveling above Mach 5 have motivated an interest in novel thermal management strategies. Here, we use a low-temperature stainless steel-water system to experimentally investigate the feasibility of metallic leading edge heat pipe concepts for thermal management in an efficient load supporting structure. The concept is based upon a two-phase, high thermal conductance “heat pipe” which redistributes the localized thermal flux created at the leading edge stagnation point over a larger surface for effective removal. Structural efficiency is achieved by configuring the system as a wedge-shaped sandwich panel with an I-cell core that simultaneously permits axial vapor and returns liquid flow. The measured axial temperature profiles resulting from a localized thermal flux applied to the tip are consistent with effective thermal spreading that lowered the peak leading edge temperature and reduced the temperature gradients when compared with an equivalent structure containing no working fluid. A simple finite element model that treated the vapor as an equivalent, high thermal conductivity material was in good agreement with these experiments. The model is then used to design a niobium alloy-lithium system that is shown to be suitable for enthalpy conditions representative of Mach 7 scramjet-powered flight. The study indicates that the surface temperature reductions of heat pipe-based leading edges may be sufficient to permit the use of nonablative, refractory metal leading edges with oxidation protection in hypersonic environments.
- 1 September 2018
- Published by Elsevier in European Journal of Mechanics - A/Solids
- Vol. 71, 64-76
Impact of granular slugs on rigid targets: Effect of grain shape and fracture
- 1 September 2018
- Published by Elsevier in European Journal of Mechanics - A/Solids
- Vol. 71, 64-76
Impact of granular slugs on rigid targets: Effect of grain shape and fracture