SKSatoshi Koizumi

Satoshi Koizumi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Satoshi Koizumi has a total of 107 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Ultraprecise anisotropy mapping of Young's modulus in single-crystal diamond via mechanical resonance

    by Zhaozong Zhang, Grace Wong, Zilong Zhang, Wen Zhao, Guo Chen, Satoshi Koizumi, Meiyong Liao

    The exceptional stiffness of diamond is strongly anisotropic due to its crystal structure, yet experimental quantification of Young's modulus along different orientations remains limited. Here, we present a direct measurement of elastic anisotropy in microwave plasma chemical vapor deposition (MPCVD) single-crystal diamond (SCD) by analyzing the resonance frequencies of cantilevers aligned along distinct crystallographic directions. The measured Young's modulus exhibited a minimum value of 1085 ± 21 GPa along the ⟨100⟩ direction and a maximum value of 1189 ± 22 GPa along the ⟨110⟩ direction. The compliance constants derived from the MPCVD-SCD differ substantially from previously reported values for natural diamonds and are more consistent with first-principles theoretical values. This method enables precise determination of orientation-dependent stiffness, revealing significant variation in Young's modulus across crystallographic axes. These insights are critical for the design of diamond-based micro- and nano-mechanical systems as well as other high-precision devices, where directional elasticity strongly influences performance.


  • Open Access

    Optical properties of single-crystal diamond MEMS: mitigating substrate interference

    by Keyun Gu, Zilong Zhang, Zhaozong Zhang, Jian Huang, Yasuo Koide, Satoshi Koizumi, Meiyong Liao


  • Surface desorption properties of hydrogen-terminated diamond detected by micromechanical resonator

    by Keyun Gu, Zilong Zhang, Jian Huang, Yasuo Koide, Satoshi Koizumi, Meiyong Liao

    Diamond, with its ultra-wide bandgap energy, has emerged as an extreme semiconductor due to its extraordinary electronic and thermal properties. The hydrogen-terminated diamond surface has attracted extensive attention due to its unique p-type surface conductivity. However, the fundamental nature of this p-type conductivity remains incompletely understood using existing surface analysis techniques. In this study, we investigate the dynamic thermal desorption of surface adsorbates on hydrogen-terminated diamond using single-crystal diamond microelectromechanical systems resonators, avoiding charging-related issues. By analyzing variations in resonance performance and surface conductivity, we uncover several key findings: (i) The desorption of surface adsorbates reaches saturation at approximately 873 K. (ii) The desorbed mass per unit area is around 2.3 fg/μm2, corresponding to an equivalent thickness of approximately 1 nm. (iii) The surface conductivity of hydrogen-terminated diamond can be fully restored even after annealing at 873 K, indicating the thermal stability of C–H bonds. This work offers an alternative insight into the surface properties of hydrogen-terminated diamond, accelerating the development of highly reliable diamond-based electronic devices.


  • P-Channel MOSFETs on Phosphorous-Doped n-Type Diamond

    by Wen Zhao, Satoshi Koizumi, Meiyong Liao

    P-channel metal-oxide-semiconductor field-effect transistors (MOSFETs) have been demonstrated on phosphorus-doped n-type diamond epilayers. The p-channel nature arises from the surface conductivity resulting from hydrogenated termination on the n-type diamond surface. The MOSFET exhibits normally-on properties and shows a threshold of 1.8 V for the phosphorus concentration of 10 16 cm -3 and an on/off ratio of 10 7 . The maximum drain current is approximately -4.5 mA/mm and the transconductance is 0.75 mS/mm, which decreases as the phosphorus concentration in the n-type diamond epilayer increases. The demonstration of p-channel MOSFETs on n-type diamond epilayers paves the way for the development of complementary MOS (CMOS) circuits on a single diamond wafer.


  • Top Cited Papers
    Open Access

    High‐Temperature and High‐Electron Mobility Metal‐Oxide‐Semiconductor Field‐Effect Transistors Based on N‐Type Diamond

    by Meiyong Liao, Huanying Sun, Satoshi Koizumi

    Diamond holds the highest figure‐of‐merits among all the known semiconductors for next‐generation electronic devices far beyond the performance of conventional semiconductor silicon. To realize diamond integrated circuits, both n‐ and p‐channel conductivity are required for the development of diamond complementary metal‐oxide‐semiconductor (CMOS) devices, as those established for semiconductor silicon. However, diamond CMOS has never been achieved due to the challenge in n‐type channel MOS field‐effect transistors (MOSFETs). Here, electronic‐grade phosphorus‐doped n‐type diamond epilayer with an atomically flat surface based on step‐flow nucleation mode is fabricated. Consequently, n‐channel diamond MOSFETs are demonstrated. The n‐type diamond MOSFETs exhibit a high field‐effect mobility around 150 cm 2 V −1 s −1 at 573 K, which is the highest among all the n‐channel MOSFETs based on wide‐bandgap semiconductors. This work enables the development of energy‐efficient and high‐reliability CMOS integrated circuits for high‐power electronics, integrated spintronics, and extreme sensors under harsh environments.


  • Temperature Dependence of Betavoltaic Cell Performance of Diamond pn Junction Diode

    by Takehiro Shimaoka, Hitoshi Umezawa, Gwenole Jacopin, Satoshi Koizumi, Takeshi Fujiwara, Julien Pernot

    Temperature dependence of the energy conversion efficiency of diamond pn junction betavoltaic cells was evaluated. We fabricated pseudo vertical diamond pn junction diode and characterized its energy conversion efficiency under electron beam irradiation from 5-300 K. The diamond pn junction diode exhibits energy conversion efficiencies of 18-24% at 150-300 K, which is more than twice as high as those of silicon PiN diode. On the other hand, below 100 K, the energy conversion efficiency of the diode significantly drops due to the increase of series resistance of diamond. Above 150K, the diamond pn junction diode presents smaller temperature dependency on energy conversion efficiency than that of silicon diode, which would make diamond pn junction betavoltaic cells, a promising device for energy harvesting in remote sensing devices over a wide temperature range except in the cryogenic region.


  • Open Access

    Effect of defects on Q factors of single-crystal diamond MEMS resonators

    by Zilong Zhang, Guo Chen, Keyun Gu, Satoshi Koizumi, Meiyong Liao


  • Enhancement of magnetic sensing performance of diamond resonators coupling with magnetic-strictive FeGa films by various interlayers

    by Zilong Zhang, Liwen Sang, Jian Huang, Linjun Wang, Yasuo Koide, Satoshi Koizumi, Meiyong Liao


  • Propagation of dislocations in diamond (111) homoepitaxial layer

    by Kimiyoshi Ichikawa, Satoshi Koizumi, Tokuyuki Teraji

    Dislocations in a diamond (111) homoepitaxial layer were investigated in terms of the line directions and types. After a thick homoepitaxial layer was grown on a {111} high-pressure high-temperature (HPHT) substrate using chemical vapor deposition (CVD), the Raman spectra of diamond were taken using a confocal setup to obtain the spatial distribution of the peak positions of the diamond Raman line. Dislocations in the CVD layer and HPHT substrate were detected as local stress variation in the peak position images. The line directions of dislocations were, respectively, [112] for the HPHT substrate and [011] for the CVD layer. Local stress variation was in the [1¯1¯2 ] direction in both the CVD layer and the HPHT substrate. The Burgers vector deduced from the local stress-variation direction indicated the dislocation structures, respectively, as an edge type for [112] dislocations in the HPHT substrate and as a 60° mixed type for [011] dislocations in the CVD layer. Because both dislocations had the same slip plane, the line direction and dislocation type changed on the same slip plane at the CVD layer/HPHT substrate interface, when dislocation in the HPHT substrate reached the CVD layer.


  • Dislocations in chemical vapor deposition diamond layer detected by confocal Raman imaging

    by K. Ichikawa, T. Shimaoka, Y. Kato, S. Koizumi, T. Teraji

    Dislocations in a homoepitaxial diamond film grown by chemical vapor deposition (CVD) were characterized by confocal Raman imaging. The diamond film was grown on a high-pressure high-temperature (HPHT) substrate using an oxygen-adding condition to minimize dislocation formation during diamond growth. The dislocation densities in the CVD thin film and substrate were found to be 3 × 104 and 2 × 104 cm−2, respectively, from large-area Raman imaging. The spatial variation of stress around dislocations in CVD diamond was analyzed three-dimensionally using in-plane images of peak positions of diamond first-order lines taken at different depths from the diamond film surface. The variational directions of the stresses depended on the types of dislocation: ⟨110⟩ variational direction corresponds to edge [001] dislocation, whereas the ⟨100⟩ variational direction corresponds to 45° mixed [001] dislocation. Most dislocations passed through the CVD thin film from the substrate. Some dislocations were newly generated at the CVD layer–substrate interface. The dislocations in CVD diamond propagate along the [001] direction of diamond crystal with the same Burgers vector in the HPHT substrate.