Bassem Mouawad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Bassem Mouawad has a total of 73 co-authors. Here are the top co-authors by number of shared publications:
- Christopher Mark Johnson
Department of Electrical and Electronic Engineering, University of Nottingham, Nottingham, U.K.
8 shared publications - Alberto Castellazzi
Kyoto University of Advanced Science
7 shared publications - Cyril Buttay
Université de Lyon, CNRS
6 shared publications Maher Soueidan
Laboratoire Ampère, Institut National des Sciences Appliquées de Lyon, Villeurbanne, France
5 shared publicationsVincent Bley
Laboratoire Plasma et Conversion d’Energie, Université Paul Sabatier, Toulouse, France
4 shared publications- Christina DiMarino
Center for Power Electronics Systems, Virginia Tech, Arlington, VA, USA
3 shared publications
Latest Publications
- 31 March 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Assemblages innovants en électronique de puissance utilisant la technique de « Spark Plasma Sintering »
L'augmentation des températures de fonctionnement est une des évolutions actuelles de l'électronique de puissance. Ce fonctionnement entraine d’une part des changements de la structure des modules de puissance notamment des structures « 3D » pour assurer un refroidissement double face des composants de puissance, et d’autre part l’utilisation de matériaux qui permettent de réduire des contraintes thermomécaniques, liées à la différence de coefficient de dilatation des matériaux, lors d’une montée en température. Le travail réalisé au cours de cette thèse consiste à développer une nouvelle structure « 3D » basée sur une technique de contact par des micropoteaux en cuivre, élaborés par électrodéposition et ensuite assemblés à un substrat céramique métallisé (notamment, un DBC : Direct Bonding Copper). Pour réaliser ce contact, une technique de frittage par SPS (Spark Plasma Sintering) est utilisée. Nous étudions dans un premier temps le collage direct de cuivre sur des massifs, puis effectuons dans un deuxième temps le collage de cuivre entre les micropoteaux et le DBC. Cette technique SPS est aussi utilisée pour la réalisation d’un nouveau substrat céramique métallisé basé sur des matériaux avec des coefficients de dilatation thermique accordés, pour les applications à haute température.
- 31 March 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Assemblages innovants en électronique de puissance utilisant la technique de « Spark Plasma Sintering »
L'augmentation des températures de fonctionnement est une des évolutions actuelles de l'électronique de puissance. Ce fonctionnement entraine d’une part des changements de la structure des modules de puissance notamment des structures « 3D » pour assurer un refroidissement double face des composants de puissance, et d’autre part l’utilisation de matériaux qui permettent de réduire des contraintes thermomécaniques, liées à la différence de coefficient de dilatation des matériaux, lors d’une montée en température. Le travail réalisé au cours de cette thèse consiste à développer une nouvelle structure « 3D » basée sur une technique de contact par des micropoteaux en cuivre, élaborés par électrodéposition et ensuite assemblés à un substrat céramique métallisé (notamment, un DBC : Direct Bonding Copper). Pour réaliser ce contact, une technique de frittage par SPS (Spark Plasma Sintering) est utilisée. Nous étudions dans un premier temps le collage direct de cuivre sur des massifs, puis effectuons dans un deuxième temps le collage de cuivre entre les micropoteaux et le DBC. Cette technique SPS est aussi utilisée pour la réalisation d’un nouveau substrat céramique métallisé basé sur des matériaux avec des coefficients de dilatation thermique accordés, pour les applications à haute température.
- 23 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 9 (4) , 3867-3876
Heterogeneous Integration of Magnetic Component Windings on Ceramic Substrates
Heterogeneous integration and the converter in package concept have been highlighted as enabling technologies to unlock the full potential of Silicon Carbide (SiC) and Gallium Nitride (GaN) devices. Control of parasitic elements in the commutation loops and passive filter integration within the power module reduce the risk of over-current and over-voltage stresses for the transistors and can improve the containment of high frequency noise at source, resulting in a safer operation of the whole converter. However, at present, the major limitation to filter integration is posed by the low energy density of commercial magnetic components. This paper shows further investigating on the integration of more reliable high power density magnetic components within the power module structure. The proposed approach consists of bonding individual copper parts, representative of single winding turns, onto an appropriately patterned ceramic substrate, thus improving the filters thermal management. At first, an experimental comparison between different bonding techniques has been carried out on the basis of mechanical performance. Finally, to prove the feasibility and repeatability of the proposed route, a complete inductor has been manufactured using solder bonding technique. Both thermal tests and simulations confirmed, that thanks to the enhanced heat exchange between inductor and cooling system, the maximum current density can be increased above commercial standards, while maintaining the temperature in a safe range for the nearby active devices.
- 23 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 9 (4) , 3867-3876
Heterogeneous Integration of Magnetic Component Windings on Ceramic Substrates
Heterogeneous integration and the converter in package concept have been highlighted as enabling technologies to unlock the full potential of Silicon Carbide (SiC) and Gallium Nitride (GaN) devices. Control of parasitic elements in the commutation loops and passive filter integration within the power module reduce the risk of over-current and over-voltage stresses for the transistors and can improve the containment of high frequency noise at source, resulting in a safer operation of the whole converter. However, at present, the major limitation to filter integration is posed by the low energy density of commercial magnetic components. This paper shows further investigating on the integration of more reliable high power density magnetic components within the power module structure. The proposed approach consists of bonding individual copper parts, representative of single winding turns, onto an appropriately patterned ceramic substrate, thus improving the filters thermal management. At first, an experimental comparison between different bonding techniques has been carried out on the basis of mechanical performance. Finally, to prove the feasibility and repeatability of the proposed route, a complete inductor has been manufactured using solder bonding technique. Both thermal tests and simulations confirmed, that thanks to the enhanced heat exchange between inductor and cooling system, the maximum current density can be increased above commercial standards, while maintaining the temperature in a safe range for the nearby active devices.
- Top Cited Papers
- 11 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (6) , 6050-6060
10-kV SiC MOSFET Power Module With Reduced Common-Mode Noise and Electric Field
The advancement of silicon carbide (SiC) power devices with voltage ratings exceeding 10 kV is expected to revolutionize medium- and high-voltage systems. However, present power module packages are limiting the performance of these unique switches. The objective of this research is to push the boundaries of high-density, high-speed, 10 kV power module packaging. The proposed package addresses the well-known electromagnetic and thermal challenges, as well as the more recent and prominent electrostatic and electromagnetic interference (EMI) issues associated with high-speed, 10 kV devices. The high-speed switching and high voltage rating of these devices causes significant EMI and high electric field. Existing power module packages are unable to address these challenges, resulting in detrimental EMI and partial discharge that limit the converter operation. This paper presents the design and testing of a 10 kV SiC MOSFET power module that switches at a record 250 V/ns without compromising the signal and ground integrity due to an integrated screen reduces the common-mode current by ten times. This screen connection simultaneously increases the partial discharge inception voltage by more than 50 %. With the integrated cooling system, the power module prototype achieves a power density of 4 W/mm3.
- 11 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (6) , 6050-6060
Top Cited Papers10-kV SiC MOSFET Power Module With Reduced Common-Mode Noise and Electric Field
The advancement of silicon carbide (SiC) power devices with voltage ratings exceeding 10 kV is expected to revolutionize medium- and high-voltage systems. However, present power module packages are limiting the performance of these unique switches. The objective of this research is to push the boundaries of high-density, high-speed, 10 kV power module packaging. The proposed package addresses the well-known electromagnetic and thermal challenges, as well as the more recent and prominent electrostatic and electromagnetic interference (EMI) issues associated with high-speed, 10 kV devices. The high-speed switching and high voltage rating of these devices causes significant EMI and high electric field. Existing power module packages are unable to address these challenges, resulting in detrimental EMI and partial discharge that limit the converter operation. This paper presents the design and testing of a 10 kV SiC MOSFET power module that switches at a record 250 V/ns without compromising the signal and ground integrity due to an integrated screen reduces the common-mode current by ten times. This screen connection simultaneously increases the partial discharge inception voltage by more than 50 %. With the integrated cooling system, the power module prototype achieves a power density of 4 W/mm3.
- 27 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 8 (1) , 381-394
Design and Experimental Validation of a Wire-Bond-Less 10-kV SiC MOSFET Power Module
Wide bandgap (WBG) power devices with voltage ratings exceeding 10 kV have the potential to revolutionize medium- and high-voltage systems due to their high-speed switching and lower ON-state losses. However, the present power module packages are limiting the performance of these unique switches. The objective of this article is to push the boundaries of high-density, high-speed, 10-kV power module packaging. The proposed package addresses the well-known electromagnetic and thermal challenges, as well as the more recent and prominent electrostatic and electromagnetic interference (EMI) issues associated with high-speed, 10-kV devices. The module achieves low and balanced parasitic inductances, resulting in a record switching speed of 250 V/ns with negligible ringing and voltage overshoot. An integrated screen reduces the common-mode (CM) current that is generated by these fast voltage transients by ten times. This screen connection simultaneously increases the partial discharge inception voltage (PDIV) by more than 50%. A compact, medium-voltage termination and system interface design is also proposed in this article. With the integrated jet-impingement cooler, the power module prototype achieves a power density of 4 W/mm 3 . This article presents the design, prototyping, and testing of this optimized package for 10-kV SiC MOSFETs.
- 27 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 8 (1) , 381-394
Design and Experimental Validation of a Wire-Bond-Less 10-kV SiC MOSFET Power Module
Wide bandgap (WBG) power devices with voltage ratings exceeding 10 kV have the potential to revolutionize medium- and high-voltage systems due to their high-speed switching and lower ON-state losses. However, the present power module packages are limiting the performance of these unique switches. The objective of this article is to push the boundaries of high-density, high-speed, 10-kV power module packaging. The proposed package addresses the well-known electromagnetic and thermal challenges, as well as the more recent and prominent electrostatic and electromagnetic interference (EMI) issues associated with high-speed, 10-kV devices. The module achieves low and balanced parasitic inductances, resulting in a record switching speed of 250 V/ns with negligible ringing and voltage overshoot. An integrated screen reduces the common-mode (CM) current that is generated by these fast voltage transients by ten times. This screen connection simultaneously increases the partial discharge inception voltage (PDIV) by more than 50%. A compact, medium-voltage termination and system interface design is also proposed in this article. With the integrated jet-impingement cooler, the power module prototype achieves a power density of 4 W/mm 3 . This article presents the design, prototyping, and testing of this optimized package for 10-kV SiC MOSFETs.
- 1 October 2018
- Published by IMAPS - International Microelectronics Assembly and Packaging Society in International Symposium on Microelectronics
- Vol. 2018 (1) , 000069-000074
Converter-Level Integration for Wide Band-Gap Automotive Power Electronics
Wide band-gap (WBG) semiconductors offer many potential benefits to designers of power electronic systems. Lower switching losses allow operation at higher switching frequencies, which in principle allows a reduction in passive component values in many converter applications. However, efficient operation at higher switching frequencies requires increased voltage and current transition rates. With conventional packaging and circuit construction, parasitic inductance and capacitance can deteriorate converter performance, reducing efficiency and adding to the electromagnetic interference (EMI) emitted from the system. Outside the commutation cell, fast voltage transitions may lead to unacceptably high levels of conducted and radiated EMI, so approaches involving the local filtering of converter outputs are attractive. To mitigate these effects in conventional modules, switching speeds are often deliberately limited and the potential benefits of using WBG technologies cannot be fully realized. Here we examine the design and realization of Converter-in-Package (CiP) modular blocks for system power levels from 100s W to 100s kW, incorporating individual commutation cells with close-coupled gate drives, input/output filtering and reduced EMI. The concept is illustrated through the realization of a modular, segmented power converter for an integrated drive.
- 1 October 2018
- Published by IMAPS - International Microelectronics Assembly and Packaging Society in International Symposium on Microelectronics
- Vol. 2018 (1) , 000069-000074
Converter-Level Integration for Wide Band-Gap Automotive Power Electronics
Wide band-gap (WBG) semiconductors offer many potential benefits to designers of power electronic systems. Lower switching losses allow operation at higher switching frequencies, which in principle allows a reduction in passive component values in many converter applications. However, efficient operation at higher switching frequencies requires increased voltage and current transition rates. With conventional packaging and circuit construction, parasitic inductance and capacitance can deteriorate converter performance, reducing efficiency and adding to the electromagnetic interference (EMI) emitted from the system. Outside the commutation cell, fast voltage transitions may lead to unacceptably high levels of conducted and radiated EMI, so approaches involving the local filtering of converter outputs are attractive. To mitigate these effects in conventional modules, switching speeds are often deliberately limited and the potential benefits of using WBG technologies cannot be fully realized. Here we examine the design and realization of Converter-in-Package (CiP) modular blocks for system power levels from 100s W to 100s kW, incorporating individual commutation cells with close-coupled gate drives, input/output filtering and reduced EMI. The concept is illustrated through the realization of a modular, segmented power converter for an integrated drive.
- Open Access
- 1 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 463-466
Dynamic performance analysis of a 3.3 kV SiC MOSFET half-bridge module with parallel chips and body-diode freewheeling
Recently, 3.3 and 6.5 kV power MOSFETs have been introduced. Based on the 3.3 kV device, a 100 A half-bridge power module has been developed, using parallel chips for current scaling and relying exclusively on the use of the transistors body-diode for current free-wheeling (i.e., no antiparallel external diode chips are used). This paper presents a thorough parametric characterization of the module switching performance. Single-chip and parallel-chip operation are investigated in both double-pulsea type tests and realistic singlephase inverter operation.
- 1 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 463-466
Open AccessDynamic performance analysis of a 3.3 kV SiC MOSFET half-bridge module with parallel chips and body-diode freewheeling
Recently, 3.3 and 6.5 kV power MOSFETs have been introduced. Based on the 3.3 kV device, a 100 A half-bridge power module has been developed, using parallel chips for current scaling and relying exclusively on the use of the transistors body-diode for current free-wheeling (i.e., no antiparallel external diode chips are used). This paper presents a thorough parametric characterization of the module switching performance. Single-chip and parallel-chip operation are investigated in both double-pulsea type tests and realistic singlephase inverter operation.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 4003-4010
Design of a novel, high-density, high-speed 10 kV SiC MOSFET module
High-density packaging of fast-switching power semiconductors typically requires low thermal resistance and parasitic inductance. High-density packaging of high-voltage semiconductors, such as 10 kV SiC MOSFETs, has the added challenge of maintaining low electric field concentration in order to prevent premature dielectric breakdown. This work proposes a wire-bond-less, sandwich structure with embedded decoupling capacitors and stacked ceramic substrates in order to realize a high-density module capable of high-speed switching with low electric field concentration and EMI. This is the first time that these advanced packaging techniques have been applied to a 10 kV SiC MOSFET module.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 4003-4010
Design of a novel, high-density, high-speed 10 kV SiC MOSFET module
High-density packaging of fast-switching power semiconductors typically requires low thermal resistance and parasitic inductance. High-density packaging of high-voltage semiconductors, such as 10 kV SiC MOSFETs, has the added challenge of maintaining low electric field concentration in order to prevent premature dielectric breakdown. This work proposes a wire-bond-less, sandwich structure with embedded decoupling capacitors and stacked ceramic substrates in order to realize a high-density module capable of high-speed switching with low electric field concentration and EMI. This is the first time that these advanced packaging techniques have been applied to a 10 kV SiC MOSFET module.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. P.1-P.9
3.3 kV SiC JBS diode configurable rectifier module
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. P.1-P.9
3.3 kV SiC JBS diode configurable rectifier module
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 347-352
VHDL-AMS modelling of multi-chip SiC power modules
This paper presents a methodology for modelling of multichip Silicon Carbide (SiC) power modules where multi-domain effects (electrical, thermal, and electromagnetic) in the power module can be accurately observed with minimal computational cost. Commercially available numerical analysis software are capable of showing these effects but there is currently no commercially available software package where effects from one domain (e.g. thermal) can be fed back to affect other domains (e.g. electrical) in real time simulation. In this work, an advanced semiconductor model was created with physics based equations to describe the electrical, thermal and electromagnetic aspects of the model. An algorithm to increase the computational efficiency of the thermal aspect of the model was also presented. The model was then tested in steady state, dynamic and multichip configurations and the results were validated with experiments and simulations from previous work in this field.
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 347-352
VHDL-AMS modelling of multi-chip SiC power modules
This paper presents a methodology for modelling of multichip Silicon Carbide (SiC) power modules where multi-domain effects (electrical, thermal, and electromagnetic) in the power module can be accurately observed with minimal computational cost. Commercially available numerical analysis software are capable of showing these effects but there is currently no commercially available software package where effects from one domain (e.g. thermal) can be fed back to affect other domains (e.g. electrical) in real time simulation. In this work, an advanced semiconductor model was created with physics based equations to describe the electrical, thermal and electromagnetic aspects of the model. An algorithm to increase the computational efficiency of the thermal aspect of the model was also presented. The model was then tested in steady state, dynamic and multichip configurations and the results were validated with experiments and simulations from previous work in this field.