OCOlga Anatolievna Chikova

Olga Anatolievna Chikova

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Olga Anatolievna Chikova has a total of 67 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Analysis of corrosion action of liquid heat-carrier Pb–Bi eutectic on stainless steel

    by O. A. Chikova, Shuailong Li, О. А. Чикова, Шайлун Ли

    The corrosion behavior of 316L, 15–15Ti and T91 steel samples exposed to the lead-bismuth liquid-metal heat carrier Pb–Bi eutectic (Pb–Bie) was studied under static conditions at 500 °C for 200, 300 and 400 h. The authors evaluated thickness and morphology of the diffusion zone at the steel/Pb–Bie interface, oxide-layer structure, Pb and Bi penetration depth, and signs of intergranular melt penetration. Steel class affects the physicochemical parameters of corrosion. Austenitic steels 316L and 15–15Ti undergo local intergranular corrosion and Pb–Bie penetration along grain boundaries to a depth of about 5·10 –5 m after 300 h of contact, which can be considered a prerequisite for liquid-metal embrittlement. Martensitic T91 steel is affected by corrosion associated with dissolution, mutual diffusion of elements. All studied samples showed signs of oxidation during contact with the melt. An external Fe 3 O 4 oxide layer (≈10 –5 m) and an internal (Fe,Cr) 3 O 4 layer (≈5·10 –5 m thick) were observed. As contact time increased, Pb and Bi penetration in steel increased from nearly zero after 200 h to about 10 –4 m after 400 h. A difference was found between austenitic and martensitic steels not only in the depth of melt penetration, but also in the localization of damage. A theoretical assessment of the liquid-metal embrittlement conditions of 316L steel samples exposed to Pb–Bie melt is presented using the Griffiths and Robertson models. Using the lattice mean-field theory, the authors theoretically studied the relationship between surface wetting and the steel crystal lattice type. The interaction energy between the steel surface and Pb–Bie decreases more rapidly with increasing temperature for austenitic steel than for martensitic one.

  • Open Access

    Motivation for choosing UrFU Master’s degree program by students from China as a manifestation of self‑regulated and continuous learning

    by A. L. Nevolina, G. A. Tkachuk, O. A. Chikova, Shen Yanfan, А. Л. Неволина, Г. А. Ткачук, О. А. Чикова, Шэнь Янфань

    Introduction . Currently, the leadership of the People’s Republic of China pays special attention to the issues of professional education at the master’s level. Students from the PRC studying in the Russian Federation have specific motivational learning strategies. Purpose setting. The purpose of the article is to study the specifics of the motivational strategy of learning of students – citizens of the PRC in the master’s programs of the Ural Federal University (UrFU). Methodology and methods of the study . The study of the specifics of motivation and learning strategies of UrFU master’s students from the PRC was carried out using a special scale «Motivated Learning Strategies Questionnaire of Master’s students from China – MSLQ-MC». MSLQ-MC includes five indicators (factors): «orientation to internal goals», «perceived value of learning», «self-efficacy»; «critical thinking», «learning design» has good criteria of agreement with the original data. The study involved 54 students who assessed their motivation and learning strategies on a 5-point Likert scale using the MSLQ-MC tool in English. Statistical processing of the measurement results was carried out using the SPSS 23.0 and Amos 18.0 software packages. Results . Statistical analysis of the results of measuring motivation and learning strategies of UrFU master’s students from China using the MSLQ-MC scale showed that the wording of the questions is adequate to the measurement context. The primacy of students’ internal beliefs in choosing strategies for their learning activities was revealed. Analysis of the MSLQ-MC data revealed that the choice of an educational program and a course of study have the strongest impact on the indicators of «self-efficacy», «perceived value of learning» and «orientation to internal goals», which is explained by the peculiarities of the Chinese education system. Conclusion . An original technique for measuring the motivational learning strategy of students – MSLQ-MC, which is formative in nature for successful continuation of education is presented

  • Open Access

    Mathematical modeling of electrical conductivity of melts with eutectic and monotectic interaction characteristics of components

    by O. A. Chikova, Шуайлун Ли

    The authors propose to use the generalized conductivity theory (GCT) for mathematical modeling of electrical conductivity of metallic melts with eutectic and monotectic interaction of components. The main GCT approaches are considered and analyzed: the method of transition to unit cell and the effective medium method, which allow describing the properties of heterogeneous liquid metallic systems. The paper presents a mathematical formulation of the problem of calculating the effective coefficients of electrical conductivity from the known values of the specified parameters of the initial components and their concentrations. An example of calculating the specific electrical resistance of Pb-Bi melt with eutectic interaction of the components is given. The calculation was carried out using the method of transition to the elementary cell of Rayleigh: a model of a structure with interpenetrating components, a model of a structure with isolated inclusions; and the effective medium method. The results of calculations for these models are compared with experimental data on the specific electrical resistance of liquid Pb – Bi alloys in a wide range of temperatures and concentrations. All three approaches to estimating the specific electrical resistance of Pb – Bi melts showed the results close to the experimental data. The closest values were demonstrated by the model of a structure with interpenetrating components, for which the standard deviation of the calculated values from the experimental ones was less than 4 %. The authors substantiated that the use of GCT for calculating the effective coefficients of melts’ electrical conductivity is advisable at the initial stages of developing new metallic materials with specified properties, especially in cases where direct experiments are difficult. This approach allows for a significant reduction in time and financial costs of synthesizing samples and experimentally studying their physicochemical characteristics.

  • Open Access

    Design and optimization scheme of sinter vertical cooler waste heat power generation plant based on EBSILON

    by Shuailong Li, Weishu Wang, Olga A. Chikova, Weihui Xu, Yuelong Lyu

    The new vertical sintering ore cooling furnace has a higher waste heat recovery efficiency and less environmental pollution compared to traditional belt coolers and annular coolers. This paper designs a supporting waste heat power generation system for the vertical sintering ore cooler and conducts flue gas waste heat utilization modifications on the power generation system based on EBSILON software. It compares and analyzes three modification schemes and explores the impact of the outlet water temperature of the flue gas-water heat exchanger on the additional power generation capacity of the unit, the heat rate of the power plant, and the economic benefits. The study found that Scheme 2 has the best energy-saving effect and economic performance. When the outlet water temperature of the heat exchanger is 170 °C, the additional power generation capacity of the generator is 0.438 MW, and the annual economic benefit is 1.93596 million yuan. The higher the outlet temperature of the heat exchanger, the higher the additional power generation capacity and economic benefits, with a slight decrease in the heat rate of the power plant. This paper can provide a certain reference for the design and modification of waste heat power plants for vertical sintering ore coolers.


  • Open Access

    Physico-chemical analysis of 12Kh18N9TL steel melts for quality control of cast products

    by D. P. Shvetsov, O. A. Chikova, V. S. Tsepelev, N. I. Sinitsin, V. V. V’yUkhin

    The authors studied the behavior of slag inclusions in four samples taken during casting of austenitic corrosion-resistant steel grade 12Kh18N9TL. The samples for the study were taken under production conditions after melting the charge ( 1 ), introducing Ti and FeMn, slag induction and additional loading ( 2 ), re-introducing Ti, slag induction ( 3 ), slag induction ( 4 ). The elemental composition and temperature of the melt were determined under production conditions. The physicochemical properties of the melts obtained from the selected samples were measured under laboratory conditions: surface tension and kinematic viscosity. The measurements were carried out in the temperature range from 1370 to 1760 °C in the mode of heating and subsequent cooling of the sample. When observing the sample during the measurement of surface tension, the release of slag inclusions from the volume of the drop occurs in the heating mode. During subsequent cooling of the formed drop of liquid steel, slag particles flow from the slag bath under the action of the Marangoni force. Analysis of the dependence of the slag particle ascent rate on its size showed that only particles up to 10 μm in size can remain in the melt volume, while larger particles have time to float to the surface of the liquid bath. It was found that slag particles up to 4 mm in size can flow onto the surface of the sample under the action of the Marangoni force. The volume fraction of slag inclusions was determined, and a correlation was established between it and the element composition of the sample. The authors made a conclusion about the effect of Ti additives in the melt as the cause of increase in the volume fraction of slag inclusions in the casting.

  • Quality control of metal of rolling rolls made of 8Kh3SMF steel by ultrasonic and metallographic methods

    by A. V. Belonosov, O. A. Chikova, N. A. Zaytseva

    Quality control of working rolls of a cold rolling mill made of 8Kh3SMF steel is aimed at identifying defects of metallurgical origin; it is carried out using ultrasonic and metallographic methods. The article presents the results of a comparative study of the microstructure and crystalline structure of samples taken from working rolls of a reversible rolling mill made of 8Kh3SMF steel from defective and defect-free areas according to ultrasonic testing (UT) data before quenching. Defects are identified by UT as discontinuities with a reflectivity equivalent to a diameter of 5.0–7.5 mm. As a result of metallographic examination by means of scanning electron microscopy (EDS and EBSD analysis), non-metallic inclusions of ~5-30 μm in size of four types were detected: MnS; (MnS + Al2O3 + CaO); (MnS + V + Ti) and (MnS + Ti). The metal selected from the defective area of the roll barrel contained non-metallic inclusions (MnS + V + Ti) and (MnS + Ti), which indicates non-recovery of titanium and vanadium alloying additives. The metal selected from the defective area of the roll barrel also had larger grain, fewer LAGB, greater material texture and heterogeneity of elastic properties. Consequently, the presence of defects that are identified by ultrasonic testing as discontinuities with a reflectivity equivalent to a diameter of 5.0–7.5 mm contributes to the occurrence of internal cracks in the metal during hardening and is not acceptable when concluding on compliance with quality requirements.The research was conducted at the Laboratory of non-destructive testing methods (LNMK) of Uralmashzavod and the Center for Collective Use “Modern Nanotechnologies” of the Institute of Natural Sciences and Mathematics of the Ural Federal University.The work was carried out using the equipment of the Center for Collective Use “Modern Nanotechnologies” of the Institute of Natural Sciences and Mathematics of the Ural Federal University.

  • Open Access

    Feedback literacy of a college student in e‑learning: Development and validation of a scale

    by A. A. Egorov, O. A. Chikova, R. V. Kamenev, I. V. Sartakov

    Introduction. Self-assessment of feedback literacy by college students is important for the organization of e-learning. Self-assessment of feedback literacy is an educational practice of monitoring and improving the learning process through information received by the student in the context of assessment of results. Purpose setting. The problem of developing feedback literacy among college students in vocational training using Moodle is solved through formative self-assessment. The authors develop a formative self-assessment scale for feedback literacy. A survey was conducted of 88 students of Novosibirsk Aviation Technical College named after B. S. Galushchak (Novosibirsk). Methodology and methods of the study. The methodology for analyzing the results of student self-assessment of literacy in the field of feedback in e-learning is based on the use of the Structural Equation Modeling (SEM) data analysis method. Results. Confirmatory factor analysis of the obtained data showed the acceptability of two structural models of the scale: one-factor and five factor, including five final indicators: «recognition of the value of feedback», «management of emotions», «ability to act», «ability to make judgment», «readiness to act». Exploratory factor analysis found that gender identity of student influences his self-assessment of literacy in the field of feedback – male students are more literate, and the gender dependence is especially strong for the indicators «emotion management» and «readiness to act.» Frequency of use of the Moodle is primarily associated with the «ability to act» indicator, while the belief in the usefulness of Moodle for learning is associated with the «ability to make judgment» indicator. Conclusion. A conclusion is made about the relevance of forming a theory and methodology for developing student feedback literacy in professional learning in digital format.

  • Open Access

    Model for organizing distance learning in an educational institution

    by R. V. Kamenev, O. A. Chikova, I. V. Sartakov

       Introduction. A relevant area of informatization of education management is modeling the management of an educational institution’s activities in organizing the transition to distance learning.   The purpose of the article is to develop and evaluate a structural and functional model of organizing the transition of an educational organization to distance learning based on a comparative analysis of foreign academic literature summarizing the experience of the emergency introduction of distance learning due to the coronavirus pandemic.   Purpose setting. The purpose of the article is to develop and evaluate a structural and functional model for organizing the transition of an educational organization to distance learning on the basis of a comparative analysis of foreign scientific and methodological literature.   Methodology and methods of the study. The development and evaluation of the model of the management system for the activities of an educational institution for the organization of DL included the solution of the following tasks: 1. Comparative Analysis of Foreign Academic Literature; 2. Development of a universal model for the organization of DL for educational organizations; 3. Model Quality Assessment.   Results. A model of the management system of an educational institution for organizing distance learning has been developed. The ADDIE (Analysis, Design, Development, Implement, Evaluate) educational process organization model served as a prototype. The methodology for evaluating the model for organizing the transition of an educational organization to distance learning corresponded to the TAM (Technology Acceptance Model) approach. The model was evaluated by surveying 44 experts with experience in organizing the educational process in a distance format. A static analysis of the opinions of Structural Equation Modeling (SEM) experts showed that the proposed model demonstrates sufficient compliance with the established requirements and is suitable for its intended purpose.   Conclusion. The developed model of the system for managing the activities of an educational institution for organizing distance learning is intended for use in educational institutions of the Russian Federation at all levels of education in the situation of assessing the preparation for the implementation of training in a fully interactive mode during emergency situations.

  • Kinetics of the Interaction of Co–Cu Melts with Graphite and Microstructure of Formed Metal–Carbon Composites

    by O. A. Chikova, I. G. Shirinkina, V. S. Tsepelev, N. I. Sinitsin, V. V. Vyukhin

    The time dependences of the contact angles and the wetted surface spot diameters have been measured during the interaction between Co–Cu melts with copper contents of 20, 40, and 60 at % and graphite at temperatures of 1390, 1440, 1490, 1540, and 1590°C. Under these conditions, graphite is not wetted by the Co–Cu melts: the final contact angles for Co80–Cu20, Co60–Cu40, and Co40–Cu60 are 95, 110, and 100°, respectively. Therewith, the final diameters of the wetted surface spots somewhat increase. The metallographic analysis of the microstructure of the Co–Cu–C composite materials obtained by the contact alloying of Co–Cu melts with carbon has shown that the morphology of the structural components and the phase composition of the samples depend on the copper content. Composite materials (Co–27%C–10%Cu) + (Co–32%C–62%Cu) + C and (Co–19%C–15%Cu) + (Co–25%C–72%Cu) + C obtained by the interaction of the Co–Cu melts containing 20 and 40 at % copper with graphite have a macrohomogeneous structure.