SVSofie Vogt

Sofie Vogt

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sofie Vogt has a total of 40 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Single-domain, semiconducting κ-Ga2O3 grown on isostructural ε-GaFeO3 templates

    by Clemens Petersen, Sofie Vogt, Javier Garcia Fernandez, Lasse Vines, Taisei Kano, Marius Grundmann, Hiroyuki Nishinaka, Holger von Wenckstern

    The epitaxial growth of a phase-pure, single-domain, semiconducting κ-Ga2O3 thin film is demonstrated. Multiferroic ε-GaFeO3, being isostructural to κ-Ga2O3, was used as a substrate and was initially covered by a high-temperature MIST-CVD κ-Ga2O3 seed layer. Subsequently, tin-assisted pulsed laser deposition at 550 °C was applied to grow the single-crystalline epilayer with a thickness of 400 nm. The structural properties were investigated by x-ray diffraction and transmission electron microscopy. A reciprocal space map revealed that the κ-Ga2O3 layer sustains residual strain and is only partially relaxed. Consistently, misfit dislocations were observed, indicating ongoing but incomplete strain relaxation. Secondary ion mass spectrometry confirmed efficient Sn incorporation and revealed Fe diffusion from the ε-GaFeO3 substrate. The Fe impurities segregate predominantly at the advancing growth front, resulting in only moderate bulk compensation of the κ-Ga2O3/ε-GaFeO3 layer. Temperature-dependent in-plane transport measurements revealed freeze out of free electrons with activation energies of Ea,1=48 meV and Ea,2=253 meV at intermediate and high temperatures, respectively. No measurable in-plane conductivity was observed for a reference sample deposited on c-plane sapphire, which exhibited in-plane rotational domains and nanocolumnar growth. These results demonstrate that epitaxial growth on isostructural ε-GaFeO3 enables single-crystalline, semiconducting κ-Ga2O3 and establishes the κ-Ga2O3/ε-GaFeO3 heterostructure as a promising platform for exploring polarization-charge-induced two-dimensional electron gases in multifunctional ferroelectric/ferrimagnetic oxide systems.

  • Open Access

    Coordination flexibility as key factor for variability of local structure in amorphous Zn–Sn–O and Cu–Sn–O thin films

    by Corvin Krohn, Arne Jörns, Sofie Vogt, Konrad Ritter, Sandra Montag, Sergiu Levcenko, Marius Grundmann, Holger von Wenckstern, Claudia S Schnohr

    Earth-abundant amorphous oxide semiconductors like Zn–Sn–O and Cu–Sn–O feature electrical conductivities that can be tuned over several orders of magnitude by adjusting the metal composition and oxygen content. This study investigates the element-specific local structure and amorphous nature of Zn–Sn–O and Cu–Sn–O thin films with varying Zn/Sn and Cu/Sn ratios, grown at different oxygen partial pressures by room temperature pulsed laser deposition. X-ray absorption spectroscopy was performed at the Zn, Cu and Sn K -edges, providing local coordination and structural parameters for each metal species by in-depth analysis of near edge and extended fine structures. Except for very high copper contents, all thin films are fully amorphous with no noticeable order beyond the first coordination shell. Zinc atoms keep a tetrahedral configuration with an average bond length slightly larger than that of crystalline ZnO. Tin atoms prefer an octahedral coordination similar to crystalline SnO 2 but with reduced average coordination number and slightly smaller average bond length. Copper atoms feature a CuO-like coordination with reduced average coordination number and bond length for high copper contents, while further reduction of these structural parameters for low copper contents indicates a broad distribution of local environments. The variability of the Zn–O, Sn–O and Cu–O local building blocks is thus determined by the coordination flexibility of the respective metal, being small for zinc with only one stable oxide but large for tin and copper with two stable oxides at ambient conditions. The dominant effect of the metal composition on the electrical properties of the material is given by the changing fraction of Zn–O, Cu–O and Sn–O building blocks. Undercoordinated tin atoms provide negative charge carriers, leading to increasing n-type conductivity with increasing tin content. In contrast, CuO-like environments promote p-type conductivity for Cu–Sn–O thin films with high enough copper contents.

  • Open Access

    High‐Throughput Combinatorial Synthesis of Rhombohedral α‐(Cr x Ga 1− x ) 2 O 3 Solid Solutions over the Entire Composition Range

    by Clemens Petersen, Dmitry Sayenko, Jakob Seifert, Sofie Vogt, Chris Sturm, Marius Grundmann, Holger von Wenckstern

    In this work, a novel combinatorial synthesis method, event‐triggered combinatorial PLD (ETC‐PLD), is presented, with which spatially addressable material libraries of (Cr x Ga 1− x ) 2 O 3 extending over the entire composition range on a single substrate are realized. Utilizing spatially resolved measurements techniques, the structural and optical properties of the material system are screened with high experimental throughput. Phase‐pure growth in the rhombohedral α‐phase is confirmed by X‐ray diffraction measurements, and a comparison of the epitaxy on m‐plane and a‐plane sapphire is presented. By spatially resolved spectroscopic ellipsometry measurements, bandgap engineering within the rhombohedral α‐(Cr x Ga 1− x ) 2 O 3 material system is demonstrated over an up to now unprecedented spectral range from 3.2 to 5.3 eV. These results are promising for applications of the material system in wavelength‐selective optoelectronics.


  • Open Access

    Toward Amorphous CuI‐Alloys Deposited by Magnetron Cosputtering: Structural and Microstructural Investigations

    by Christiane Dethloff, Sofie Vogt, Susanne Selle, Holger von Wenckstern, Marius Grundmann

    Two different solid solutions of CuI, namely, I and Mo x Cu 1– x I, have been deposited via reactive magnetron cosputtering to investigate the suppression of the zincblende γ‐CuI phase by the introduction of foreign atoms into the lattice. A comprehensive growth study is presented, in which sputtering in inert and reactive atmospheres (Ar + I 2 , Ar, N 2 + I 2 , N 2 ) is performed from metallic Cu, Sn, and Mo targets as well as from a CuI powder target. A strong influence of the iodine partial pressure during the deposition on the crystal quality of thin films is observed by X‐ray diffraction measurements. For optimized growth conditions, X‐ray amorphous thin films are achieved for solid solution Sn x Cu 1– x I and Mo x Cu 1– x I thin films deposited from the CuI powder target in an inert Ar atmosphere. However, a microstructural analysis of these thin films by transmission electron microscopy combined with energy‐dispersive X‐ray diffraction spectroscopy and selected area diffraction reveals a phase separation into Sn and O rich, (Mo and O rich, respectively) amorphous regions, and CuI crystallites. Oxygen concentrations between ≈10 at% and ≈70 at%, detected in the thin films, give reason to the assumption of an oxygen induced phase separation.


  • Open Access

    Toward Ultrawide Bandgap Engineering: Physical Properties of an α‐(Ti x Ga 1− x ) 2 O 3 Material Library

    by Clemens Petersen, Thorsten Schultz, Magnus Andreassen, Sofie Vogt, Norbert Koch, Marius Grundmann, Holger von Wenckstern

    Due to its high bandgap of 5.3–5.6 eV and high predicted breakdown field of 10 MV cm −1 , much attention is drawn to the ultrawide bandgap semiconductor α‐Ga 2 O 3 for applications in high‐power and solar blind optoelectronic devices. In contrast to the thermodynamically most stable β‐phase of Ga 2 O 3 , various transition metal sesquioxides with rhombohedral crystal structure and similar lattice constants to α‐Ga 2 O 3 are available for bandgap engineering toward lower bandgap energies. Therefore the material system α‐(Ti x Ga 1− x ) 2 O 3 in principle offers the possibility to tune the materials bandgap for wavelength selective optoelectronics over an extremely wide range from 5.6 eV (α‐Ga 2 O 3 ) down to 0.14 eV (α‐Ti 2 O 3 ). In this work, high‐throughput combinatorial synthesis by pulsed laser deposition is employed to realize a spatially addressable material library covering almost the entire composition range within the ternary (Ti x Ga 1− x ) y O z solid solution. Phase‐pure growth of (Ti x Ga 1− x ) 2 O 3 up to x = 0.25 is reported, exceeding previously found miscibility limits by a factor of 5. The physical properties of the material system are investigated in relation to x and bandgap engineering within the rhombohedral α‐(Ti x Ga 1− x ) 2 O 3 material system is demonstrated over an up to now unprecedented large spectral range from 4.4 to 5.3 eV.


  • Open Access

    α‐Ga 2 O 3 ‐Based Heterojunction Diodes and Junction Field‐Effect Transistors

    by Paul Bokemeyer, Clemens Petersen, Christiane Dethloff, Yang Chen, Holger von Wenckstern, Marius Grundmann, Sofie Vogt

    This article presents a comprehensive investigation into the suitability of diverse p ‐type materials for the fabrication of pn ‐heterojunctions and junction field‐effect transistors (JFETs) with α‐Ga 2 O 3 . The electrical properties of these materials are examined in detail and compared with one another in order to ascertain their relative merits. Therefore copper iodide (CuI), zinc cobalt oxide (ZCO), and nickel oxide (NiO) are used as p ‐type contacts. The smallest ideality factors are obtained for pn ‐heterojunctions utilizing CuI, whereas the highest current rectification is obtained for diodes with NiO and ZCO contacts, if an oxygen plasma treatment of the α‐Ga 2 O 3 is performed before the deposition of the p ‐type electrode. This way current rectification ratios of up to are achieved. In a next step, these findings are used to fabricate highly functional JFETs with a α‐Ga 2 O 3 channel. These devices exhibit current on/off ratios of up to and small mean sub‐threshold swings of at a low drain voltage of 3 V. High breakdown voltages of up to 418 V are achieved, regardless of the gate material.


  • Lateral α-Ga2O3:Zr metal–semiconductor field effect transistors

    by Sofie Vogt, Daniel Splith, Sebastian Köpp, Peter Schlupp, Clemens Petersen, Holger von Wenckstern, Marius Grundmann

    We present α-Ga2O3:Zr based metal–semiconductor field-effect transistors (MESFETs) with PtOx/Pt gate contacts. Pulsed laser deposition is used to grow the α-Ga2O3:Zr thin films in a two-step process on m-plane α-Al2O3. A nominally undoped α-Ga2O3 layer is grown at high growth temperature as growth template. Subsequently, a α-Ga2O3:Zr layer is grown at a lower growth temperature. We compare the performance of Ring-FET devices on a planar 30 nm thick zirconium doped layer deposited at 465 °C and mesa-FETs on a 35 nm thick thin film deposited at 500 °C. The Ring-FETs have current on/off ratios as high as 1.7×109 and a threshold voltage of −0.28 V, and they exhibit very low mean sub-threshold swing of (110±20) mV/dec. For the mesa-FETs, smaller current on/off ratios of 4×107 are measured and a threshold voltage of −1.5 V was obtained due to the larger thin film thickness. The on/off ratio is limited by a higher tunneling current in the off-regime. We present high voltage measurements, which show a breakdown of the mesa-FET device at −340 V, corresponding to a high breakdown field of 1.36 MV/cm and significantly exceeding the previously achieved breakdown voltage for α-Ga2O3 based MESFETs.


  • Zr doping in pulsed-laser-deposited α - Ga2O3 for device applications

    by S. Vogt, C. Petersen, H. von Wenckstern, M. Grundmann, T. Schultz, N. Koch

    The feasibility of zirconium doping of α-Ga2O3 grown by pulsed laser deposition is demonstrated. Targets with different zirconium contents are used to adjust the zirconium content in the thin films. Therefore, a two-step growth process is utilized, where first an undoped α-Ga2O3 thin film is grown as a high-temperature buffer layer and the zirconium-doped α-Ga2O3 layer is subsequently deposited at a lower growth temperature. Highly conductive thin films are obtained with resistivities as low as 3.3×10−3Ωcm. An electron mobility as high as 38cm2V−1s−1 is measured for a high free carrier density of 6.5×1018cm−3. The crystallization in the α-phase was confirmed by x-ray diffraction measurements. Further, a strong influence of the growth temperature on the zirconium incorporation is observed, which can be explained by the increased desorption of volatile Ga2O3 suboxides at high growth temperatures. Depth-resolved x-ray photoelectron spectroscopy measurements were employed to investigate the doping profile in the thin films. They reveal a strongly depth-dependent incorporation of the zirconium, with a decreased incorporation towards the surface. First Schottky barrier diodes on zirconium-doped α-Ga2O3 thin films with rectification ratios as high as 8.5 orders of magnitude at ±3V are presented.


  • Open Access

    Demonstration of Two Multi‐Component Target Ablation Approaches and Their Application in Combinatorial Pulsed Laser Deposition

    by A. Jörns, H. von Wenckstern, S. Vogt, P. Schlupp, M. Grundmann

    Combinatorial pulsed laser deposition (C‐PLD) based on segmented targets has led to new possibilities in the pace of discovery of novel advanced materials with significantly reduced deposition time and material consumption. However, fabrication of established segmented targets may be complex or not even possible for certain material combinations. In this article, two alternative C‐PLD techniques based on easy‐to‐fabricate segmented targets are presented. One approach uses two semi‐circular segments A and B with a systematic adjustable lateral shift of the target rotation axis from the target center. The other approach is based on a new target design defined by an ABA‐segmentation where B is a horizontal bar between two semi‐circular segments of A. Both approaches enable growth of discrete composition libraries. The concepts and important parameters are introduced and computer simulations as function of the geometric parameters are made to yield the expected thin film compositions. As proof‐of‐concept, the techniques are employed on the transparent, semiconducting ternary alloy zinc‐tin‐oxide. The simulations are in very good agreement with the experimental data. Physical properties of films grown by the demonstrated approaches are compared with those obtained by established PLD processes.


  • Open Access

    PLD of α-Ga2O3 on m-plane Al2O3: Growth regime, growth process, and structural properties

    by Clemens Petersen, Sofie Vogt, Max Kneiß, Holger von Wenckstern, Marius Grundmann

    Phase-pure α-Ga2O3 thin films with high surface quality and crystallinity have been grown on m-plane sapphire using pulsed laser deposition (PLD). Therefore, the influence of growth temperature, oxygen background pressure, and film thickness on the structural properties is investigated to determine the growth window for phase-pure corundum structured α-Ga2O3. Samples were analyzed using x-ray diffraction (XRD), atomic force microscopy (AFM), and spectroscopic ellipsometry measurements. A distinct growth window in favor of phase-pure (10.0)-oriented α-Ga2O3 for growth temperatures above 480 °C and low oxygen partial pressures p(O2) of 3 × 10−4 mbar is identified. The growth rate increases significantly with increasing oxygen pressure. Furthermore, it shows an Arrhenius-like decrease for lower temperatures, caused by the increasing desorption of volatile Ga2O suboxides. It was found that for thicker layers, the growth of monoclinic β-Ga2O3 is promoted likely facilitated by the c-facets of the α-Ga2O3 grains. This leads to a (010)-oriented island growth corroborated by stripe-like features in AFM scans and a corresponding in-plane orientation confirmed by XRD ϕ-scans. For oxygen partial pressures above 3 × 10−4 mbar and Tg < 540 °C, the formation of mixed (10.0) α-Ga2O3 and spinel-defective (110)-γ-Ga2O3 manifesting as defective inclusions was observed independent of the layer thickness d. A corresponding p(O2) − d − T phase diagram for the growth of Ga2O3 on m-plane sapphire by PLD is provided.