Frederik Stöhr
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Frederik Stöhr has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Henning Friis Poulsen
Department of Physics Technical University of Denmark Kongens Lyngby Denmark
4 shared publications - Hugh Simons
Department of Physics, Technical University of Denmark, 2800 Kgs. Lyngby, Denmark
4 shared publications - Flemming Jensen
DTU Danchip Technical University of Denmark Kongens Lyngby 2800 Denmark
3 shared publications - Ole Hansen
Technical University of Denmark
3 shared publications Jonas Michael-Lindhard
DTU Danchip, Technical University of Denmark, Kongens Lyngby DK-2800, Denmark
2 shared publications- Jörg Hübner
DTU Danchip Technical University of Denmark Kongens Lyngby 2800 Denmark
2 shared publications
Latest Publications
- Open Access
- 11 November 2015
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 5 (12) , 2804-2811
Injection molded polymeric hard X-ray lenses
A novel and economical approach for fabricating compound refractive lenses for the purpose of focusing hard X-rays is described. A silicon master was manufactured by UV-lithography and deep reactive ion etching (DRIE). Sacrificial structures were utilized, which enabled accurate control of the etching profile and were removed after DRIE. By electroplating, an inverse nickel sample was obtained, which was used as a mold insert in a commercial polymer injection molding machine. A prototype lens made of polyethylene with a focal length of 350 mm was tested using synchrotron radiation at photon energies of 17 keV. A 55 µm long line focus with a minimal waist of 770 nm (FWHM) and a total lens transmittance of 32% were measured. Due to its suitability for cheap mass production, this highly efficient optics may find widespread use in hard X-ray instruments.
- 11 November 2015
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 5 (12) , 2804-2811
Open AccessInjection molded polymeric hard X-ray lenses
A novel and economical approach for fabricating compound refractive lenses for the purpose of focusing hard X-rays is described. A silicon master was manufactured by UV-lithography and deep reactive ion etching (DRIE). Sacrificial structures were utilized, which enabled accurate control of the etching profile and were removed after DRIE. By electroplating, an inverse nickel sample was obtained, which was used as a mold insert in a commercial polymer injection molding machine. A prototype lens made of polyethylene with a focal length of 350 mm was tested using synchrotron radiation at photon energies of 17 keV. A 55 µm long line focus with a minimal waist of 770 nm (FWHM) and a total lens transmittance of 32% were measured. Due to its suitability for cheap mass production, this highly efficient optics may find widespread use in hard X-ray instruments.
- 2 November 2015
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 25 (12) , 125013
Optimizing shape uniformity and increasing structure heights of deep reactive ion etched silicon x-ray lenses
Line-focusing compound silicon x-ray lenses with structure heights exceeding 300 μ m were fabricated using deep reactive ion etching. To ensure profile uniformity over the full height, a new strategy was developed in which the perimeter of the structures was defined by trenches of constant width. The remaining sacrificial material inside the lens cavities was removed by etching through the silicon wafer. Since the wafers become fragile after through-etching, they were then adhesively bonded to a carrier wafer. Individual chips were separated using laser micro machining and the 3D shape of fabricated lenses was thoroughly characterized by a variety of means. Optical testing using synchrotron radiation with a photon energy of 56 keV yielded a 300 μ m wide beam with a waist of 980 nm (full width at half maximum) at a focal length of 1.3 m. Optical aberrations are discussed in the context of the shape analysis, where a slight bowing of the lens sidewalls and an insufficiently uniform apex region are identified as resolution-limiting factors. Despite these, the proposed fabrication route proved a viable approach for producing x-ray lenses with large structure heights and provides the means to improve the resolution and capabilities of modern x-ray techniques such as x-ray microscopy and 3D x-ray diffraction.
- 2 November 2015
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 25 (12) , 125013
Optimizing shape uniformity and increasing structure heights of deep reactive ion etched silicon x-ray lenses
Line-focusing compound silicon x-ray lenses with structure heights exceeding 300 μ m were fabricated using deep reactive ion etching. To ensure profile uniformity over the full height, a new strategy was developed in which the perimeter of the structures was defined by trenches of constant width. The remaining sacrificial material inside the lens cavities was removed by etching through the silicon wafer. Since the wafers become fragile after through-etching, they were then adhesively bonded to a carrier wafer. Individual chips were separated using laser micro machining and the 3D shape of fabricated lenses was thoroughly characterized by a variety of means. Optical testing using synchrotron radiation with a photon energy of 56 keV yielded a 300 μ m wide beam with a waist of 980 nm (full width at half maximum) at a focal length of 1.3 m. Optical aberrations are discussed in the context of the shape analysis, where a slight bowing of the lens sidewalls and an insufficiently uniform apex region are identified as resolution-limiting factors. Despite these, the proposed fabrication route proved a viable approach for producing x-ray lenses with large structure heights and provides the means to improve the resolution and capabilities of modern x-ray techniques such as x-ray microscopy and 3D x-ray diffraction.
- Top Cited PapersOpen Access
- 14 January 2015
- Published by Springer Nature in Nature Communications
- Vol. 6 (1) , 6098
Dark-field X-ray microscopy for multiscale structural characterization
Many physical and mechanical properties of crystalline materials depend strongly on their internal structure, which is typically organized into grains and domains on several length scales. Here we present dark-field X-ray microscopy; a non-destructive microscopy technique for the three-dimensional mapping of orientations and stresses on lengths scales from 100 nm to 1 mm within embedded sampling volumes. The technique, which allows ‘zooming’ in and out in both direct and angular space, is demonstrated by an annealing study of plastically deformed aluminium. Facilitating the direct study of the interactions between crystalline elements is a key step towards the formulation and validation of multiscale models that account for the entire heterogeneity of a material. Furthermore, dark-field X-ray microscopy is well suited to applied topics, where the structural evolution of internal nanoscale elements (for example, positioned at interfaces) is crucial to the performance and lifetime of macro-scale devices and components thereof.
- 14 January 2015
- Published by Springer Nature in Nature Communications
- Vol. 6 (1) , 6098
Top Cited PapersOpen AccessDark-field X-ray microscopy for multiscale structural characterization
Many physical and mechanical properties of crystalline materials depend strongly on their internal structure, which is typically organized into grains and domains on several length scales. Here we present dark-field X-ray microscopy; a non-destructive microscopy technique for the three-dimensional mapping of orientations and stresses on lengths scales from 100 nm to 1 mm within embedded sampling volumes. The technique, which allows ‘zooming’ in and out in both direct and angular space, is demonstrated by an annealing study of plastically deformed aluminium. Facilitating the direct study of the interactions between crystalline elements is a key step towards the formulation and validation of multiscale models that account for the entire heterogeneity of a material. Furthermore, dark-field X-ray microscopy is well suited to applied topics, where the structural evolution of internal nanoscale elements (for example, positioned at interfaces) is crucial to the performance and lifetime of macro-scale devices and components thereof.
- 26 December 2014
- Published by Elsevier in Microelectronic Engineering
- Vol. 141, 6-11
Three-dimensional nanometrology of microstructures by replica molding and large-range atomic force microscopy
- 26 December 2014
- Published by Elsevier in Microelectronic Engineering
- Vol. 141, 6-11
Three-dimensional nanometrology of microstructures by replica molding and large-range atomic force microscopy
- Open Access
- 27 February 2013
- Published by American Chemical Society (ACS) in Journal of the American Society for Mass Spectrometry
- Vol. 24 (4) , 602-608
Single-Photon Ionization of Organic Molecules Beyond 10 kDa
The volatilization and soft ionization of complex neutral macromolecules at low energies has remained an outstanding challenge for several decades [(1)]. Most volatilization techniques in mass spec...
- 27 February 2013
- Published by American Chemical Society (ACS) in Journal of the American Society for Mass Spectrometry
- Vol. 24 (4) , 602-608
Open AccessSingle-Photon Ionization of Organic Molecules Beyond 10 kDa
The volatilization and soft ionization of complex neutral macromolecules at low energies has remained an outstanding challenge for several decades [(1)]. Most volatilization techniques in mass spec...