Hansang Lim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hansang Lim has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
C.W. Choi
2 shared publications- Gyunha Kim
Seoul, Seoul Korea (the Republic of)
2 shared publications - Jeong Rok Gim
LIG Nex1
2 shared publications Jun Seo Park
Hyundai Kia Motors, Hwaseong-si, Gyeonggi-do, Republic of Korea
2 shared publications- Kyoung Won Jang
Research Center, Dongnam Institute of Radiological and Medical Sciences, Busan, Korea
2 shared publications M. Lee
2 shared publications
Latest Publications
- Open Access
- 2 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 106867-106873
Time Pickoff Method Using Dual-Edge Discrimination to Mitigate Time Walk
Precise generation of a timing pulse at the signal is crucial for high-resolution time measurements, accomplished using a time pickoff circuit. The primary challenge in time pickoff circuits is to minimize the dependency of timing pulse generation on signal amplitude, which causes a timing error known as time walk. This study proposes a time pickoff method using dual-edge discrimination, which measures the crossing times of the signal at both its leading and trailing edges and calculates a reference time when the signal reaches its peak amplitude. The proposed time pickoff method was theoretically analyzed, demonstrating that the reference time was independent of variations in the crossing times due to the signal amplitude variations. Furthermore, the timing error caused by the charge sensitivity of the comparator used in the time pickoff circuit was reduced. The proposed time pickoff method was validated through experiments for signals with 2-ns rise and 3-ns fall times and amplitudes ranging from 18 mV to 1.8 V, resulting in a time walk of 145 ps.
- 2 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 106867-106873
Open AccessTime Pickoff Method Using Dual-Edge Discrimination to Mitigate Time Walk
Precise generation of a timing pulse at the signal is crucial for high-resolution time measurements, accomplished using a time pickoff circuit. The primary challenge in time pickoff circuits is to minimize the dependency of timing pulse generation on signal amplitude, which causes a timing error known as time walk. This study proposes a time pickoff method using dual-edge discrimination, which measures the crossing times of the signal at both its leading and trailing edges and calculates a reference time when the signal reaches its peak amplitude. The proposed time pickoff method was theoretically analyzed, demonstrating that the reference time was independent of variations in the crossing times due to the signal amplitude variations. Furthermore, the timing error caused by the charge sensitivity of the comparator used in the time pickoff circuit was reduced. The proposed time pickoff method was validated through experiments for signals with 2-ns rise and 3-ns fall times and amplitudes ranging from 18 mV to 1.8 V, resulting in a time walk of 145 ps.
- 4 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Intelligent Transportation Systems
- Vol. 25 (9) , 10885-10895
Online Ecological Energy Management for Plug-In HEVs Using Optimal SOC Prediction and Stochastic Optimization
Optimizing power demand and distribution in real time is the primary challenge in the energy management of plug-in hybrid electric vehicles. To address this challenge, this study proposes an online ecological energy management strategy using the optimal state of charge (SOC) prediction and stochastic optimization. Future energy-consumption features at each location are computed from the traffic and route information of the entire remaining trip and the optimal SOC value at the next location is predicted from the computed features using a recurrent neural network. By considering the predicted optimal SOC and average speed as references, the speed and SOC values at the next location are optimized using a modified estimation of distribution algorithm (EDA). The process of generating initial and new populations in EDA is modified for fast and reliable convergence. The optimal SOC prediction considering the energy consumption for the entire remaining trip from the current to final locations ensures long-term optimality. Stochastic aspects of the modified EDA can compensate for potential neural-network errors. The prediction and optimization of driving only up to the next location enables to adapt to the changes in traffic conditions. Moreover, the energy efficiency is further improved by optimizing power demand based on the characteristics of the drivetrain, as well as traffic and route conditions. Because the traffic and route information are provided on a location basis, management is performed in a distance domain. The proposed management strategy is evaluated in diverse driving scenarios, and it exhibits good performance, comparable to that of the offline optimization.
- 4 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Intelligent Transportation Systems
- Vol. 25 (9) , 10885-10895
Online Ecological Energy Management for Plug-In HEVs Using Optimal SOC Prediction and Stochastic Optimization
Optimizing power demand and distribution in real time is the primary challenge in the energy management of plug-in hybrid electric vehicles. To address this challenge, this study proposes an online ecological energy management strategy using the optimal state of charge (SOC) prediction and stochastic optimization. Future energy-consumption features at each location are computed from the traffic and route information of the entire remaining trip and the optimal SOC value at the next location is predicted from the computed features using a recurrent neural network. By considering the predicted optimal SOC and average speed as references, the speed and SOC values at the next location are optimized using a modified estimation of distribution algorithm (EDA). The process of generating initial and new populations in EDA is modified for fast and reliable convergence. The optimal SOC prediction considering the energy consumption for the entire remaining trip from the current to final locations ensures long-term optimality. Stochastic aspects of the modified EDA can compensate for potential neural-network errors. The prediction and optimization of driving only up to the next location enables to adapt to the changes in traffic conditions. Moreover, the energy efficiency is further improved by optimizing power demand based on the characteristics of the drivetrain, as well as traffic and route conditions. Because the traffic and route information are provided on a location basis, management is performed in a distance domain. The proposed management strategy is evaluated in diverse driving scenarios, and it exhibits good performance, comparable to that of the offline optimization.
- 30 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 71 (9) , 9375-9383
Ringing Suppression in a Controller Area Network With Flexible Data Rate Using Frequency-Selective Impedance Matching and Temporal Impedance Switching
An inherent impedance mismatch in a controller area network with flexible data rate (CAN-FD) network gives rise to signal distortion called ringing. Ringing is one of the main causes of communication errors and performance degradation. In this paper, a ringing suppression system is proposed, which alleviates the impedance mismatch at two mismatch locations: the unterminated CAN nodes and the divergence points of bus lines. At the unterminated CAN nodes, a temporal impedance switching circuit, including a matching resistor and a limiting diode, is added. The circuit is controlled to only engage right after a dominant-to-recessive transition when ringing likely occurs. At the divergence points, a frequency-selective impedance matching circuit is inserted. The circuit consists of a resistor, a capacitor, and an inductor connected in parallel, which is also designed to activate only during state transitions with the dependency of their impedance on frequency. Thus, the side effects on CAN-FD operations can be prevented. The performance of the ringing suppression system is verified by experiments. The experimental results demonstrate that the proposed system reduces ringing to a level lower than the input threshold for recessive bit detection in diverse bus configurations and supports more reliable CAN-FD communication.
- 30 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 71 (9) , 9375-9383
Ringing Suppression in a Controller Area Network With Flexible Data Rate Using Frequency-Selective Impedance Matching and Temporal Impedance Switching
An inherent impedance mismatch in a controller area network with flexible data rate (CAN-FD) network gives rise to signal distortion called ringing. Ringing is one of the main causes of communication errors and performance degradation. In this paper, a ringing suppression system is proposed, which alleviates the impedance mismatch at two mismatch locations: the unterminated CAN nodes and the divergence points of bus lines. At the unterminated CAN nodes, a temporal impedance switching circuit, including a matching resistor and a limiting diode, is added. The circuit is controlled to only engage right after a dominant-to-recessive transition when ringing likely occurs. At the divergence points, a frequency-selective impedance matching circuit is inserted. The circuit consists of a resistor, a capacitor, and an inductor connected in parallel, which is also designed to activate only during state transitions with the dependency of their impedance on frequency. Thus, the side effects on CAN-FD operations can be prevented. The performance of the ringing suppression system is verified by experiments. The experimental results demonstrate that the proposed system reduces ringing to a level lower than the input threshold for recessive bit detection in diverse bus configurations and supports more reliable CAN-FD communication.
- 25 February 2022
- Published by Elsevier in Physica Medica
- Vol. 94, S103-S104
REAL-TIME DOSE ESTIMATION USING A BEAM CURRENT TRANSFORMER FOR FLASH PRECLINICAL STUDIES
- 25 February 2022
- Published by Elsevier in Physica Medica
- Vol. 94, S103-S104
REAL-TIME DOSE ESTIMATION USING A BEAM CURRENT TRANSFORMER FOR FLASH PRECLINICAL STUDIES
- 25 February 2022
- Published by Elsevier in Physica Medica
- Vol. 94, S97
APPLICATION TO IN VITRO AND IN VIVO EXPERIMENTS OF THE FLASH ELECTRON BEEM IRRADIATOR DEVELOPED BY DIRAMS
- 25 February 2022
- Published by Elsevier in Physica Medica
- Vol. 94, S97
APPLICATION TO IN VITRO AND IN VIVO EXPERIMENTS OF THE FLASH ELECTRON BEEM IRRADIATOR DEVELOPED BY DIRAMS
- 22 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 68 (9) , 8906-8915
Quantitative Analysis of Ringing in a Controller Area Network With Flexible Data Rate for Reliable Physical Layer Designs
Signal distortion, called ringing, in a controller area network with flexible data rate (CAN-FD) causes asymmetry of propagation delay throughout a network, which is dependent on its physical bus design and becomes a critical issue in limiting the data rate. Thus, the bus structure of a CAN-FD is investigated and a transfer function of ringing is modeled by considering the physical bus configuration and features of a controller area network transceiver. The effects of the main parameters of the physical bus, such as the stub line length and number of stub lines connected to a joint connector, are then quantitatively analyzed using the presented model. When a practical bus structure is considered, additional signal distortion owing to a neighboring connector in a physical bus is modeled and analyzed. These analytical results are confirmed experimentally. Their comparison shows that the presented model-based analysis can closely approximate the size and time response of ringing and the extent of bit time distortion. The presented model-based analysis facilitates reliable communication performance by estimating the ringing and resulting asymmetry of the propagation delay for a given physical bus design and, if necessary, adjusting the design.
- 22 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 68 (9) , 8906-8915
Quantitative Analysis of Ringing in a Controller Area Network With Flexible Data Rate for Reliable Physical Layer Designs
Signal distortion, called ringing, in a controller area network with flexible data rate (CAN-FD) causes asymmetry of propagation delay throughout a network, which is dependent on its physical bus design and becomes a critical issue in limiting the data rate. Thus, the bus structure of a CAN-FD is investigated and a transfer function of ringing is modeled by considering the physical bus configuration and features of a controller area network transceiver. The effects of the main parameters of the physical bus, such as the stub line length and number of stub lines connected to a joint connector, are then quantitatively analyzed using the presented model. When a practical bus structure is considered, additional signal distortion owing to a neighboring connector in a physical bus is modeled and analyzed. These analytical results are confirmed experimentally. Their comparison shows that the presented model-based analysis can closely approximate the size and time response of ringing and the extent of bit time distortion. The presented model-based analysis facilitates reliable communication performance by estimating the ringing and resulting asymmetry of the propagation delay for a given physical bus design and, if necessary, adjusting the design.
- 4 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 68 (11) , 10679-10686
Ringing Suppression in a Controller Area Network With Flexible Data Rate Using Impedance Switching and a Limiter
The ringing and the resulting asymmetry in the propagation delay are the main causes of bandwidth degradation and communication errors in a controller area network (CAN) with flexible data rate. Therefore, in this paper, the mechanism of ringing is analyzed, and the ringing suppression circuit is proposed based on the analysis. The proposed circuit includes an impedance matching resistor and a forward-biased diode for terminating the repetition of reflections and limiting the magnitude of the ringing. These components are temporarily connected by operating a switch that is controlled by the TxD signal of a CAN controller so that the ringing suppression circuit only engages when necessary and at the correct time. The performance of the ringing suppression circuit is verified by experiments. The experimental results show that the proposed circuit keeps the ringing adequately suppressed and the good symmetry in the propagation delay across the physical bus is possessed.
- 4 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 68 (11) , 10679-10686
Ringing Suppression in a Controller Area Network With Flexible Data Rate Using Impedance Switching and a Limiter
The ringing and the resulting asymmetry in the propagation delay are the main causes of bandwidth degradation and communication errors in a controller area network (CAN) with flexible data rate. Therefore, in this paper, the mechanism of ringing is analyzed, and the ringing suppression circuit is proposed based on the analysis. The proposed circuit includes an impedance matching resistor and a forward-biased diode for terminating the repetition of reflections and limiting the magnitude of the ringing. These components are temporarily connected by operating a switch that is controlled by the TxD signal of a CAN controller so that the ringing suppression circuit only engages when necessary and at the correct time. The performance of the ringing suppression circuit is verified by experiments. The experimental results show that the proposed circuit keeps the ringing adequately suppressed and the good symmetry in the propagation delay across the physical bus is possessed.
- 3 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 67 (10) , 9312-9323
Hierarchical Energy Management for Power-Split Plug-In HEVs Using Distance-Based Optimized Speed and SOC Profiles
This paper proposes a distance-based two-stage energy management strategy for power-split plug-in hybrid electric vehicles (PHEVs). One stage is for long-term optimization and the other is for short-term adaptation to actual traffic conditions. Energy consumption in PHEVs depends on the characteristics of the drivetrain as well as the operating conditions such as power demands and their split. Thus, prior to departure, the operating conditions for a whole trip are optimized for the drivetrain characteristics and trip information, which generates optimal speed and state-of-charge profiles. While driving, the operating conditions are adapted to current traffic conditions for a short horizon on the basis of long-term optimization results. In consideration of the changeability of traffic conditions, the proposed energy management strategy is performed in a distance domain, which localizes the effects of changes in traffic conditions on the long-term optimization results. Therefore, this distance-based two-stage strategy improves the balance between the optimality and the real-time computing time, which is suitable for online management. A model for the propulsion system in a PHEV and the energy management strategy were formulated in a distance domain. An estimation of distribution algorithm was used for long-term optimization and local adaptation.
- 3 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 67 (10) , 9312-9323
Hierarchical Energy Management for Power-Split Plug-In HEVs Using Distance-Based Optimized Speed and SOC Profiles
This paper proposes a distance-based two-stage energy management strategy for power-split plug-in hybrid electric vehicles (PHEVs). One stage is for long-term optimization and the other is for short-term adaptation to actual traffic conditions. Energy consumption in PHEVs depends on the characteristics of the drivetrain as well as the operating conditions such as power demands and their split. Thus, prior to departure, the operating conditions for a whole trip are optimized for the drivetrain characteristics and trip information, which generates optimal speed and state-of-charge profiles. While driving, the operating conditions are adapted to current traffic conditions for a short horizon on the basis of long-term optimization results. In consideration of the changeability of traffic conditions, the proposed energy management strategy is performed in a distance domain, which localizes the effects of changes in traffic conditions on the long-term optimization results. Therefore, this distance-based two-stage strategy improves the balance between the optimality and the real-time computing time, which is suitable for online management. A model for the propulsion system in a PHEV and the energy management strategy were formulated in a distance domain. An estimation of distribution algorithm was used for long-term optimization and local adaptation.
- 10 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 66 (8) , 6663-6675
A Distance-Based Two-Stage Ecological Driving System Using an Estimation of Distribution Algorithm and Model Predictive Control
This paper proposes a distance-based two-stage ecological (eco-) driving scheme by using estimation of distribution algorithms (EDA) and model-based prediction of traffic conditions. Before departure, the optimal speed profile for an entire route is generated by an EDA in combination with speedup approaches for a faster computing time, which can optimize the complex cost function of ecodriving without simplification within a reasonably short computing time. This optimization is performed in a distance domain for localizing changes in the optimal speed profile due to traffic conditions while driving. After departure, by taking the optimal speed profile and actual traffic conditions into consideration, the speed profile for a short term-to only the next location-is adapted. In order to reliably react to actual traffic conditions, additional points are interpolated into the long-term distance step and fine control of speeds at the additional points is established, which is based on a predictive model for estimating the spacing to the preceding vehicle. The proposed ecodriving system is evaluated in two types of route conditions, and its results are compared with the optimization result by the quadratic programming method. This comparison shows that an EDA can generate a speed profile with better optimization results in terms of fuel efficiency and driving time within a shorter computing time.
- 10 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 66 (8) , 6663-6675
A Distance-Based Two-Stage Ecological Driving System Using an Estimation of Distribution Algorithm and Model Predictive Control
This paper proposes a distance-based two-stage ecological (eco-) driving scheme by using estimation of distribution algorithms (EDA) and model-based prediction of traffic conditions. Before departure, the optimal speed profile for an entire route is generated by an EDA in combination with speedup approaches for a faster computing time, which can optimize the complex cost function of ecodriving without simplification within a reasonably short computing time. This optimization is performed in a distance domain for localizing changes in the optimal speed profile due to traffic conditions while driving. After departure, by taking the optimal speed profile and actual traffic conditions into consideration, the speed profile for a short term-to only the next location-is adapted. In order to reliably react to actual traffic conditions, additional points are interpolated into the long-term distance step and fine control of speeds at the additional points is established, which is based on a predictive model for estimating the spacing to the preceding vehicle. The proposed ecodriving system is evaluated in two types of route conditions, and its results are compared with the optimization result by the quadratic programming method. This comparison shows that an EDA can generate a speed profile with better optimization results in terms of fuel efficiency and driving time within a shorter computing time.