Jae-Woo Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jae-Woo Kim has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Jun-Tae Kang
Electronics and Telecommunications Research Institute (Korea, Republic of)
14 shared publications Yoon-Ho Song
13 shared publications- Jin-Woo Jeong
Electronics and Telecommunications Research Institute, Daejeon 305-700, Korea
11 shared publications Sungyoul Choi
10 shared publicationsSeungjoon Ahn
5 shared publicationsJin-Woo Jeong
4 shared publications
Latest Publications
- 10 October 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (42) , 49854-49864
Effects of Interfacial Electron Transport on Field Electron Emission from Carbon Nanotube Paste Emitters
Field electron emission from carbon nanotubes (CNT) is preceded by the transport of electrons from the cathode metal to emission sites. Specifically, a supporting layer indispensable for adhesion of CNT paste emitters onto the cathode metal would impose a potential barrier, depending on its work function and interfacial electron transport behaviors. In this paper, we investigated the supporting layer of silicon carbide and nickel nanoparticles reacted onto a Kovar alloy (Fe-Ni-Co) cathode substrate, which has been adopted for reliable CNT paste emitters. The X-ray diffraction, X-ray photoelectron spectroscopy, ultraviolet photoelectron spectroscopy, and electrical conductivity measurements showed that the reaction of silicon carbide and nickel nanoparticles on the Kovar metal strongly depends upon the post-vacuum-annealing conditions and can be classified into two procedures of a diffusion-induced reaction (DIR) and a diffusion-limited reaction (DLR). The prolonged annealing at 750 °C for 5 h before the main annealing of the CNT paste emitters at 800 °C for 5 min led to the DIR that has enhanced the Ni silicide phase and a lower potential barrier for the interfacial electron transport, resulting in increased and weakly temperature-dependent field electron emission from the CNT paste emitters. On the other hand, the DLR with only the main anneal of the CNT paste emitters at 800 °C for 5 min gave rise to a higher potential barrier for the electron transport and so lower and strongly temperature-dependent field electron emission. From the results of the interfacial electron transport for the DIR and DLR mechanisms in the CNT paste emitters, we concluded that the ambient temperature dependency of field electron emission from CNT tips in the moderate range of up to 400 °C, still controversial, is mainly attributed to the supporting layer of the CNT emitter rather than its intrinsic electron emission.
- 10 October 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (42) , 49854-49864
Effects of Interfacial Electron Transport on Field Electron Emission from Carbon Nanotube Paste Emitters
Field electron emission from carbon nanotubes (CNT) is preceded by the transport of electrons from the cathode metal to emission sites. Specifically, a supporting layer indispensable for adhesion of CNT paste emitters onto the cathode metal would impose a potential barrier, depending on its work function and interfacial electron transport behaviors. In this paper, we investigated the supporting layer of silicon carbide and nickel nanoparticles reacted onto a Kovar alloy (Fe-Ni-Co) cathode substrate, which has been adopted for reliable CNT paste emitters. The X-ray diffraction, X-ray photoelectron spectroscopy, ultraviolet photoelectron spectroscopy, and electrical conductivity measurements showed that the reaction of silicon carbide and nickel nanoparticles on the Kovar metal strongly depends upon the post-vacuum-annealing conditions and can be classified into two procedures of a diffusion-induced reaction (DIR) and a diffusion-limited reaction (DLR). The prolonged annealing at 750 °C for 5 h before the main annealing of the CNT paste emitters at 800 °C for 5 min led to the DIR that has enhanced the Ni silicide phase and a lower potential barrier for the interfacial electron transport, resulting in increased and weakly temperature-dependent field electron emission from the CNT paste emitters. On the other hand, the DLR with only the main anneal of the CNT paste emitters at 800 °C for 5 min gave rise to a higher potential barrier for the electron transport and so lower and strongly temperature-dependent field electron emission. From the results of the interfacial electron transport for the DIR and DLR mechanisms in the CNT paste emitters, we concluded that the ambient temperature dependency of field electron emission from CNT tips in the moderate range of up to 400 °C, still controversial, is mainly attributed to the supporting layer of the CNT emitter rather than its intrinsic electron emission.
- 23 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (3) , 1192-1197
Stabilized and Equalized Field-Emission Currents From Carbon Nanotube Emitters by Cascade Active-Current-Control
- 23 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (3) , 1192-1197
Stabilized and Equalized Field-Emission Currents From Carbon Nanotube Emitters by Cascade Active-Current-Control
- 1 January 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 946-949
A high performance and ultra wide tuned capacitor using netted membrane structure for reconfigurable RF systems
This paper reports ultra-wide tuned RF micro-electro mechanical systems (MEMS) tunable capacitor using netted membrane structure for highly miniaturized and reconfigurable RF devices and systems applications. The proposed capacitor is also designed to achieve high linearity and capacitance values for commercial applications. Since the netted membrane is stuck to the dielectric layer of the bottom electrode not at once but each in turn as the actuation voltage is increased. In accordingly, it provides extremely superior linearity and wide tuning range. The fabricated RF MEMS tunable capacitor exhibited the linearity factor (LF) of 99.29 % in capacitance versus voltage (C-V) response and the capacitance tuning range of 1.78 ~ 9.15 pF at 1 GHz, respectively.
- 1 January 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 946-949
A high performance and ultra wide tuned capacitor using netted membrane structure for reconfigurable RF systems
This paper reports ultra-wide tuned RF micro-electro mechanical systems (MEMS) tunable capacitor using netted membrane structure for highly miniaturized and reconfigurable RF devices and systems applications. The proposed capacitor is also designed to achieve high linearity and capacitance values for commercial applications. Since the netted membrane is stuck to the dielectric layer of the bottom electrode not at once but each in turn as the actuation voltage is increased. In accordingly, it provides extremely superior linearity and wide tuning range. The fabricated RF MEMS tunable capacitor exhibited the linearity factor (LF) of 99.29 % in capacitance versus voltage (C-V) response and the capacitance tuning range of 1.78 ~ 9.15 pF at 1 GHz, respectively.
- 16 January 2014
- Published by IOP Publishing in Nanotechnology
- Vol. 25 (6) , 065201
Highly reliable field electron emitters produced from reproducible damage-free carbon nanotube composite pastes with optimal inorganic fillers
Highly reliable field electron emitters were developed using a formulation for reproducible damage-free carbon nanotube (CNT) composite pastes with optimal inorganic fillers and a ball-milling method. We carefully controlled the ball-milling sequence and time to avoid any damage to the CNTs, which incorporated fillers that were fully dispersed as paste constituents. The field electron emitters fabricated by printing the CNT pastes were found to exhibit almost perfect adhesion of the CNT emitters to the cathode, along with good uniformity and reproducibility. A high field enhancement factor of around 10,000 was achieved from the CNT field emitters developed. By selecting nano-sized metal alloys and oxides and using the same formulation sequence, we also developed reliable field emitters that could survive high-temperature post processing. These field emitters had high durability to post vacuum annealing at 950 °C, guaranteeing survival of the brazing process used in the sealing of field emission x-ray tubes. We evaluated the field emitters in a triode configuration in the harsh environment of a tiny vacuum-sealed vessel and observed very reliable operation for 30 h at a high current density of 350 mA cm(-2). The CNT pastes and related field emitters that were developed could be usefully applied in reliable field emission devices.
- 16 January 2014
- Published by IOP Publishing in Nanotechnology
- Vol. 25 (6) , 065201
Highly reliable field electron emitters produced from reproducible damage-free carbon nanotube composite pastes with optimal inorganic fillers
Highly reliable field electron emitters were developed using a formulation for reproducible damage-free carbon nanotube (CNT) composite pastes with optimal inorganic fillers and a ball-milling method. We carefully controlled the ball-milling sequence and time to avoid any damage to the CNTs, which incorporated fillers that were fully dispersed as paste constituents. The field electron emitters fabricated by printing the CNT pastes were found to exhibit almost perfect adhesion of the CNT emitters to the cathode, along with good uniformity and reproducibility. A high field enhancement factor of around 10,000 was achieved from the CNT field emitters developed. By selecting nano-sized metal alloys and oxides and using the same formulation sequence, we also developed reliable field emitters that could survive high-temperature post processing. These field emitters had high durability to post vacuum annealing at 950 °C, guaranteeing survival of the brazing process used in the sealing of field emission x-ray tubes. We evaluated the field emitters in a triode configuration in the harsh environment of a tiny vacuum-sealed vessel and observed very reliable operation for 30 h at a high current density of 350 mA cm(-2). The CNT pastes and related field emitters that were developed could be usefully applied in reliable field emission devices.
- 6 March 2013
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8668, 866861
A digital compact x-ray tube with carbon nanotube field emitters for advanced imaging systems
We have successfully developed a fully vacuum-sealed CNT x-ray source in a very compact tube without any active vacuum pump. The brazing process was specially designed and adopted for the vacuum sealing of the x-ray tube at an elevated temperature. This method enables us to obtain and maintain a desired vacuum level for the reliable electron emission from the CNT emitters after the vacuum packaging. The CNT x-ray tube also had a novel focusing electrode to effectively focus electron beams from the CNT emitters on a small area of the anode target, giving a small focal spot of below 0.3 mm with a large tube current of above 50 mA. The active-current control modulated the CNT x-ray source digitally with a low voltage of below 5 V and enhanced its stability further. Also, the pull-up circuit positioned at the cathode node of the x-ray tube shortened the response time down to several micro second. The developed CNT x-ray tube can open up new applications in medical imaging like a stationary tomosynthesis or pulsed fluoroscopy over conventional hot-cathode x-ray sources.
- 6 March 2013
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8668, 866861
A digital compact x-ray tube with carbon nanotube field emitters for advanced imaging systems
We have successfully developed a fully vacuum-sealed CNT x-ray source in a very compact tube without any active vacuum pump. The brazing process was specially designed and adopted for the vacuum sealing of the x-ray tube at an elevated temperature. This method enables us to obtain and maintain a desired vacuum level for the reliable electron emission from the CNT emitters after the vacuum packaging. The CNT x-ray tube also had a novel focusing electrode to effectively focus electron beams from the CNT emitters on a small area of the anode target, giving a small focal spot of below 0.3 mm with a large tube current of above 50 mA. The active-current control modulated the CNT x-ray source digitally with a low voltage of below 5 V and enhanced its stability further. Also, the pull-up circuit positioned at the cathode node of the x-ray tube shortened the response time down to several micro second. The developed CNT x-ray tube can open up new applications in medical imaging like a stationary tomosynthesis or pulsed fluoroscopy over conventional hot-cathode x-ray sources.
- 1 February 2013
- Published by IOP Publishing in Nanotechnology
- Vol. 24 (8) , 085201
A vacuum-sealed compact x-ray tube based on focused carbon nanotube field-emission electrons
We report on a fully vacuum-sealed compact x-ray tube based on focused carbon nanotube (CNT) field-emission electrons for various radiography applications. The specially designed two-step brazing process enabled us to accomplish a good vacuum level for the stable and reliable operation of the x-ray tube without any active vacuum pump. Also, the integrated focusing electrodes in the field-emission electron gun focused electron beams from the CNT emitters onto the anode target effectively, giving a small focal spot of around 0.3 mm with a large current of above 50 mA. The active-current control through the cathode electrode of the x-ray tube led a fast digital modulation of x-ray dose with a low voltage of below 5 V. The fabricated compact x-ray tube showed a stable and reliable operation, indicating good maintenance of a vacuum level of below 5 × 10(-6) Torr and the possibility of field-emission x-ray tubes in a stand-alone device without an active pumping system.
- 1 February 2013
- Published by IOP Publishing in Nanotechnology
- Vol. 24 (8) , 085201
A vacuum-sealed compact x-ray tube based on focused carbon nanotube field-emission electrons
We report on a fully vacuum-sealed compact x-ray tube based on focused carbon nanotube (CNT) field-emission electrons for various radiography applications. The specially designed two-step brazing process enabled us to accomplish a good vacuum level for the stable and reliable operation of the x-ray tube without any active vacuum pump. Also, the integrated focusing electrodes in the field-emission electron gun focused electron beams from the CNT emitters onto the anode target effectively, giving a small focal spot of around 0.3 mm with a large current of above 50 mA. The active-current control through the cathode electrode of the x-ray tube led a fast digital modulation of x-ray dose with a low voltage of below 5 V. The fabricated compact x-ray tube showed a stable and reliable operation, indicating good maintenance of a vacuum level of below 5 × 10(-6) Torr and the possibility of field-emission x-ray tubes in a stand-alone device without an active pumping system.
- 14 January 2013
- Published by AIP Publishing in Applied Physics Letters
- Vol. 102 (2) , 023504
A digital miniature x-ray tube with a high-density triode carbon nanotube field emitter
We have fabricated a digital miniature x-ray tube (6 mm in diameter and 32 mm in length) with a high-density triode carbon nanotube (CNT) field emitter for special x-ray applications. The triode CNT emitter was densely formed within a diameter of below 4 mm with the focusing-functional gate. The brazing process enables us to obtain and maintain a desired vacuum level for the reliable electron emission from the CNT emitters after the vacuum packaging. The miniature x-ray tube exhibited a stable and reliable operation over 250 h in a pulse mode at an anode voltage of above 25 kV.
- 14 January 2013
- Published by AIP Publishing in Applied Physics Letters
- Vol. 102 (2) , 023504
A digital miniature x-ray tube with a high-density triode carbon nanotube field emitter
We have fabricated a digital miniature x-ray tube (6 mm in diameter and 32 mm in length) with a high-density triode carbon nanotube (CNT) field emitter for special x-ray applications. The triode CNT emitter was densely formed within a diameter of below 4 mm with the focusing-functional gate. The brazing process enables us to obtain and maintain a desired vacuum level for the reliable electron emission from the CNT emitters after the vacuum packaging. The miniature x-ray tube exhibited a stable and reliable operation over 250 h in a pulse mode at an anode voltage of above 25 kV.
- 1 July 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21642370,p. 1-2
Development of fully vacuum-sealed X-ray tubes with carbon nanotube field emitters
Summary form only given. We, for the first time, developed fully vacuum-sealed X-ray tubes with carbon nanotube field emitters. The specially designed brazing process has been adopted for the vacuum sealing of the X-ray tube. The fabricated two types of X-ray tubes showed a good operation with a high stability and long lifetime.
- 1 July 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21642370,p. 1-2
Development of fully vacuum-sealed X-ray tubes with carbon nanotube field emitters
Summary form only given. We, for the first time, developed fully vacuum-sealed X-ray tubes with carbon nanotube field emitters. The specially designed brazing process has been adopted for the vacuum sealing of the X-ray tube. The fabricated two types of X-ray tubes showed a good operation with a high stability and long lifetime.
- 1 July 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21642370,p. 1-2
A dramatic improvement in the lifetime of the fully vacuum-sealed micro-focusing X-ray tube for stationary digital breast tomosynthesis
We have successfully fabricated the reliable vacuum-sealed X-ray tube with carbon nanotube (CNT) emitters through a specially designed brazing process. The robust CNT emitters were also adopted for high-temperature endurance during the brazing process. The stable field emission current from the sealed X-ray tube indicated a good maintenance of vacuum level needed for the CNT field emitters. The stability and reliability of the vacuum-sealed X-ray tube could be further improved by the active-current control unit having a wide saturation range for a constant current.
- 1 July 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21642370,p. 1-2
A dramatic improvement in the lifetime of the fully vacuum-sealed micro-focusing X-ray tube for stationary digital breast tomosynthesis
We have successfully fabricated the reliable vacuum-sealed X-ray tube with carbon nanotube (CNT) emitters through a specially designed brazing process. The robust CNT emitters were also adopted for high-temperature endurance during the brazing process. The stable field emission current from the sealed X-ray tube indicated a good maintenance of vacuum level needed for the CNT field emitters. The stability and reliability of the vacuum-sealed X-ray tube could be further improved by the active-current control unit having a wide saturation range for a constant current.