Milad Sharifi Sorkherizi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Milad Sharifi Sorkherizi has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Ahmed Abdelwahed Kishk
Concordia University
5 shared publications - Abbas Vosoogh
Gapwaves AB, Gothenburg, Sweden
1 shared publication - Abdel-Razik Sebak
Department of Electrical and Computer Engineering, Concordia University, Montreal, QC H3G 1M8, Canada
1 shared publication - Abdolmehdi Dadgarpour
Electrical and Computer Engineering Department, Concordia University, Montreal, QC, Canada
1 shared publication - Ashraf Uz Zaman
Chalmers University of Technology
1 shared publication - Herbert Zirath
Chalmers University of Technology
1 shared publication
Latest Publications
- 14 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 68 (5) , 3673-3684
High-Gain 60 GHz Linear Antenna Array Loaded With Electric and Magnetic Metamaterial Resonators
A substrate integrated waveguide (SIW)-fed bow-tie antenna that is loaded with meander-line H-shaped electric metamaterial resonators and double-sided split ring resonators (DSRRs) (magnetic metamaterial resonators) is proposed to realize a single high-gain antenna at 60 GHz. The antenna achieves a maximum gain of 13.8 dBi at 62 GHz from a single element. Subsequently, eight elements are combined into a high-gain 1 x 8 linear array of SIW-fed bow-tie antennas loaded with electric and magnetic resonators, fed using a corporate feed network. The measured results demonstrate a reflection coefficient less than -10 dB over the frequency range of 56-66 GHz, corresponding to a 16.3% bandwidth, while the maximum gain of the antenna array corresponds to 20.4 dBi at 62 GHz with a size of 5 lambda x7 lambda x1.4 lambda. Over the frequency range of 56-65 GHz, the gain is relatively flat and exceeds 18 dBi. The antenna has a maximum measured radiation efficiency of 79% and a maximum aperture efficiency of 87%.
- 14 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 68 (5) , 3673-3684
High-Gain 60 GHz Linear Antenna Array Loaded With Electric and Magnetic Metamaterial Resonators
A substrate integrated waveguide (SIW)-fed bow-tie antenna that is loaded with meander-line H-shaped electric metamaterial resonators and double-sided split ring resonators (DSRRs) (magnetic metamaterial resonators) is proposed to realize a single high-gain antenna at 60 GHz. The antenna achieves a maximum gain of 13.8 dBi at 62 GHz from a single element. Subsequently, eight elements are combined into a high-gain 1 x 8 linear array of SIW-fed bow-tie antennas loaded with electric and magnetic resonators, fed using a corporate feed network. The measured results demonstrate a reflection coefficient less than -10 dB over the frequency range of 56-66 GHz, corresponding to a 16.3% bandwidth, while the maximum gain of the antenna array corresponds to 20.4 dBi at 62 GHz with a size of 5 lambda x7 lambda x1.4 lambda. Over the frequency range of 56-65 GHz, the gain is relatively flat and exceeds 18 dBi. The antenna has a maximum measured radiation efficiency of 79% and a maximum aperture efficiency of 87%.
- 13 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 67 (9) , 3783-3797
Compact Integrated Full-Duplex Gap Waveguide-Based Radio Front End For Multi-Gbit/s Point-to-Point Backhaul Links at E-Band
This paper presents the design and realization of a high data rate radio front-end module for point-to-point backhaul links at E-band. The design module consists of four vertically stacked unconnected metal layers without any galvanic and electrical contact requirements among the building blocks, by using gap waveguide technology. The module components are a high-gain array antenna, diplexer, and circuitry consisting of a transmitter (Tx) and a receiver (Rx) monolithic microwave integrated circuits (MMICs) on a carrier board, which is successfully integrated into one package with a novel architecture and a compact form. The diplexer consists of two direct-coupled cavity bandpass filters with channels at 71-76 GHz and 81-86 GHz with a measured return loss of 15 dB and an isolation greater than 50 dB. A wideband $16x16$ slot array antenna with a measured gain of more than 31 dBi is used to provide high directivity. The measured results show that the packaged transmitter provides a conversion gain of 22 and 20 dB at 76 and 86 GHz, respectively, with an output power of 14 and 16 dBm at 1-dB gain compression point, at the same frequencies. The packaged receiver shows an average conversion gain of 20 dB at 71-76-GHz and 24 dB at 81-86-GHz bands. A real-time wireless data transmission is successfully demonstrated with a data rate of 8 Gbit/s using 32-quadrature amplitude modulated signal over 1.8-GHz channel bandwidth with spectral efficiency of 4.44 bit/s/Hz. The proposed radio front end provides the advantages of low loss, high efficiency, compact integration, and a simple mechanical assembly, which makes it a suitable solution for small-cell backhaul links.- 13 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 67 (9) , 3783-3797
Compact Integrated Full-Duplex Gap Waveguide-Based Radio Front End For Multi-Gbit/s Point-to-Point Backhaul Links at E-Band
This paper presents the design and realization of a high data rate radio front-end module for point-to-point backhaul links at E-band. The design module consists of four vertically stacked unconnected metal layers without any galvanic and electrical contact requirements among the building blocks, by using gap waveguide technology. The module components are a high-gain array antenna, diplexer, and circuitry consisting of a transmitter (Tx) and a receiver (Rx) monolithic microwave integrated circuits (MMICs) on a carrier board, which is successfully integrated into one package with a novel architecture and a compact form. The diplexer consists of two direct-coupled cavity bandpass filters with channels at 71-76 GHz and 81-86 GHz with a measured return loss of 15 dB and an isolation greater than 50 dB. A wideband $16x16$ slot array antenna with a measured gain of more than 31 dBi is used to provide high directivity. The measured results show that the packaged transmitter provides a conversion gain of 22 and 20 dB at 76 and 86 GHz, respectively, with an output power of 14 and 16 dBm at 1-dB gain compression point, at the same frequencies. The packaged receiver shows an average conversion gain of 20 dB at 71-76-GHz and 24 dB at 81-86-GHz bands. A real-time wireless data transmission is successfully demonstrated with a data rate of 8 Gbit/s using 32-quadrature amplitude modulated signal over 1.8-GHz channel bandwidth with spectral efficiency of 4.44 bit/s/Hz. The proposed radio front end provides the advantages of low loss, high efficiency, compact integration, and a simple mechanical assembly, which makes it a suitable solution for small-cell backhaul links.- 6 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 7 (9) , 1419-1431
Self-Packaged, Low-Loss, Planar Bandpass Filters for Millimeter-Wave Application Based on Printed Gap Waveguide Technology
A new concept of printed planar technology is introduced for the realization of low-loss bandpass filters in millimeter band. The new technology is self-packaged, and the insertion loss shows meaningful improvement compared to microstrip (MS) filters. The designs are based on the ridge gap waveguide (RGW), which is composed of printed parallel-plate waveguide surrounded by beds of mushrooms that suppress the signal around the waveguide. Several examples are designed, optimized, and measured. All-pole bandpass filters and filters with finite transmission zeros are proposed and studied. The performance of the proposed designs is compared to MS filters with different packaging options. In addition, an efficient transition from MS to printed RGW is designed and used in the circuits. The proposed circuits are low-cost and realizable using conventional printed circuit board technology. Measured results show good agreement with the analyses.
- 6 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 7 (9) , 1419-1431
Self-Packaged, Low-Loss, Planar Bandpass Filters for Millimeter-Wave Application Based on Printed Gap Waveguide Technology
A new concept of printed planar technology is introduced for the realization of low-loss bandpass filters in millimeter band. The new technology is self-packaged, and the insertion loss shows meaningful improvement compared to microstrip (MS) filters. The designs are based on the ridge gap waveguide (RGW), which is composed of printed parallel-plate waveguide surrounded by beds of mushrooms that suppress the signal around the waveguide. Several examples are designed, optimized, and measured. All-pole bandpass filters and filters with finite transmission zeros are proposed and studied. The performance of the proposed designs is compared to MS filters with different packaging options. In addition, an efficient transition from MS to printed RGW is designed and used in the circuits. The proposed circuits are low-cost and realizable using conventional printed circuit board technology. Measured results show good agreement with the analyses.
- 14 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 65 (8) , 2893-2905
Use of Group Delay of Sub-Circuits in Optimization of Wideband Large-Scale Bandpass Filters and Diplexers
A new method is proposed for the design of large-scale wideband resonator-coupled bandpass filters and diplexers. Corrected group delay responses of sub-circuits in combination with space mapping are used to compute the physical dimensions from the coupling matrix model. The coupling matrices are designed using the available theories. The method is based on dividing the structures into many sub-circuits and calculating the group delay responses of the reflection from which the coupling parameters and cavities’ resonant frequencies can be extracted. Using a linear space mapping, the structures are optimized efficiently. Depending on the structure’s complexity, few to no full-wave optimization is needed to tune the structures to the true designated filtering function. Bandpass filters and diplexers with bandwidths up to approximately 22% have been designed successfully using the proposed approach. A novel stacked cascaded quadruplet filter has been developed using this method. The design of wideband all-pole filters and diplexers are addressed in the paper.
- 14 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 65 (8) , 2893-2905
Use of Group Delay of Sub-Circuits in Optimization of Wideband Large-Scale Bandpass Filters and Diplexers
A new method is proposed for the design of large-scale wideband resonator-coupled bandpass filters and diplexers. Corrected group delay responses of sub-circuits in combination with space mapping are used to compute the physical dimensions from the coupling matrix model. The coupling matrices are designed using the available theories. The method is based on dividing the structures into many sub-circuits and calculating the group delay responses of the reflection from which the coupling parameters and cavities’ resonant frequencies can be extracted. Using a linear space mapping, the structures are optimized efficiently. Depending on the structure’s complexity, few to no full-wave optimization is needed to tune the structures to the true designated filtering function. Bandpass filters and diplexers with bandwidths up to approximately 22% have been designed successfully using the proposed approach. A novel stacked cascaded quadruplet filter has been developed using this method. The design of wideband all-pole filters and diplexers are addressed in the paper.
- 17 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 26 (9) , 657-659
Fully Printed Gap Waveguide With Facilitated Design Properties
An improved concept is introduced to facilitate the design of low-loss planar circuits using printed gap waveguide technology. The method is based on using separate layers to realize the EBG cells and the lines. As a result, the operating bandwidth of the waveguide is increased compared to the printed ridge gap waveguide. Also, the design process is simplified regarding the placement of the cells around the resonators and lines. Measured results of a line with two 90° bends and a quadruplet bandpass filter are presented that prove the concept. A transition to microstrip line is used in order to acquire the ability to use test probe fixture.
- 17 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 26 (9) , 657-659
Fully Printed Gap Waveguide With Facilitated Design Properties
An improved concept is introduced to facilitate the design of low-loss planar circuits using printed gap waveguide technology. The method is based on using separate layers to realize the EBG cells and the lines. As a result, the operating bandwidth of the waveguide is increased compared to the printed ridge gap waveguide. Also, the design process is simplified regarding the placement of the cells around the resonators and lines. Measured results of a line with two 90° bends and a quadruplet bandpass filter are presented that prove the concept. A transition to microstrip line is used in order to acquire the ability to use test probe fixture.