Philip E. Hancock
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Philip E. Hancock has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Paul Hayden
Environmental Flow (EnFlo) Laboratory, University of Surrey, Guildford, UK
4 shared publications Frauke Pascheke
University of Surrey
3 shared publicationsPaul Hayden
EnFlo Laboratory, School of Mechanical Engineering Sciences, University of Surrey, Guildford, Surrey, UK
3 shared publicationsS. Zhang
University of Surrey
2 shared publicationsC. Cao
Fluids Research Centre, School of Engineering, University of Surrey, Guildford, Surrey, GU2 7XH, UK
1 shared publicationF Pascheke
Institute for Oceanography, University of Hamburg, Hamburg, Germany
1 shared publication
Latest Publications
- Open Access
- 1 March 2024
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 16 (2)
The wake of a large wind turbine in stable atmospheric boundary layer flow, simulated in the EnFlo stratified-flow wind tunnel
The EnFlo stratified-flow wind tunnel is described, and the parameterization of stable atmospheric boundary layers in the context of wind turbines and stability classification is given, as are the scaling constraints for stratified-flow wind tunnel experiments. Wake measurements of mean velocity, Reynolds stresses, and turbulent heat flux were made for three mild stable states, including overlying inversion, and the neutral state. The depth of the atmospheric boundary layer was kept constant, and so the results show the effect of change in stability alone, without the change in scale that would also arise in full scale measurements, an advantage provided by wind tunnel experiments. The simulated boundary-layer wind-speed profile is the same in each case, its height slightly exceeding the blade-tip top height, and the velocity deficit at the turbine is also the same in each, implying a constant thrust coefficient. In the near wake the momentum deficit rises more rapidly in the stable cases, and stays higher further downstream where it is subsequently reduced by turbulent mixing. The wake grows less rapidly in the vertical direction in the stable cases, both above and below the hub height, the height above growing still less rapidly with an imposed inversion, while the height below is unaffected by the inversion. The wake width is largely unaffected by stability. Stability reduces the Reynolds stresses in the wake over and above the reduction in the undisturbed flow; there is not a simple superposition. In the lower part of the wake the stresses are not affected by the inversion, while they are in the upper part. Turbulent heat flux is increased in the bulk of the wake, more so with an inversion, but is reduced to the surface and unaffected by an inversion.
- 1 March 2024
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 16 (2)
Open AccessThe wake of a large wind turbine in stable atmospheric boundary layer flow, simulated in the EnFlo stratified-flow wind tunnel
The EnFlo stratified-flow wind tunnel is described, and the parameterization of stable atmospheric boundary layers in the context of wind turbines and stability classification is given, as are the scaling constraints for stratified-flow wind tunnel experiments. Wake measurements of mean velocity, Reynolds stresses, and turbulent heat flux were made for three mild stable states, including overlying inversion, and the neutral state. The depth of the atmospheric boundary layer was kept constant, and so the results show the effect of change in stability alone, without the change in scale that would also arise in full scale measurements, an advantage provided by wind tunnel experiments. The simulated boundary-layer wind-speed profile is the same in each case, its height slightly exceeding the blade-tip top height, and the velocity deficit at the turbine is also the same in each, implying a constant thrust coefficient. In the near wake the momentum deficit rises more rapidly in the stable cases, and stays higher further downstream where it is subsequently reduced by turbulent mixing. The wake grows less rapidly in the vertical direction in the stable cases, both above and below the hub height, the height above growing still less rapidly with an imposed inversion, while the height below is unaffected by the inversion. The wake width is largely unaffected by stability. Stability reduces the Reynolds stresses in the wake over and above the reduction in the undisturbed flow; there is not a simple superposition. In the lower part of the wake the stresses are not affected by the inversion, while they are in the upper part. Turbulent heat flux is increased in the bulk of the wake, more so with an inversion, but is reduced to the surface and unaffected by an inversion.
- Open Access
- 4 September 2023
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 970
Wind turbine wakes: experimental investigation of two-point correlations and the effect of stable thermal stability
Wind tunnel experiments are performed in both neutral and stable boundary layers to study the effect of thermal stability on the wake of a single turbine and on the wakes of two axially aligned turbines, thereby also showing the influence of the second turbine on the impinging wake. In the undisturbed stable boundary layers, the turbulence length scales are significantly smaller in the vertical and longitudinal directions (up to 50 % and $\approx$ 40 %, respectively), compared with the neutral flow, while the lateral length scale is unaffected. The reductions are larger with the imposed inversion of a second stable case, except in the near-wall region. In the neutral case, the length scales in the wake flow of the single turbine are reduced both vertically and laterally (up to 50 % and nearly 40 %, respectively). While there is significant upstream influence of a second turbine (on mean and turbulence quantities), there is virtually no upstream effect on vertical length scales. However, curiously, the presence of the second turbine aids length-scale recovery in both directions. Longitudinally, each turbine contributes to successive reduction in coherence. The effect of stability on the turbulence length scales in the wake flows is non-trivial: at the top of the boundary layer, the reduction in the wall-normal length scale is dominated by the thermal effect, while closer to the wall, the wake processes strongly modulate this reduction. Laterally, the turbines’ rotation promotes asymmetry, while stability opposes this tendency. The longitudinal coherence, significantly reduced by the wake flows, is less affected by the boundary layer's thermal stability.- 4 September 2023
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 970
Open AccessWind turbine wakes: experimental investigation of two-point correlations and the effect of stable thermal stability
Wind tunnel experiments are performed in both neutral and stable boundary layers to study the effect of thermal stability on the wake of a single turbine and on the wakes of two axially aligned turbines, thereby also showing the influence of the second turbine on the impinging wake. In the undisturbed stable boundary layers, the turbulence length scales are significantly smaller in the vertical and longitudinal directions (up to 50 % and $\approx$ 40 %, respectively), compared with the neutral flow, while the lateral length scale is unaffected. The reductions are larger with the imposed inversion of a second stable case, except in the near-wall region. In the neutral case, the length scales in the wake flow of the single turbine are reduced both vertically and laterally (up to 50 % and nearly 40 %, respectively). While there is significant upstream influence of a second turbine (on mean and turbulence quantities), there is virtually no upstream effect on vertical length scales. However, curiously, the presence of the second turbine aids length-scale recovery in both directions. Longitudinally, each turbine contributes to successive reduction in coherence. The effect of stability on the turbulence length scales in the wake flows is non-trivial: at the top of the boundary layer, the reduction in the wall-normal length scale is dominated by the thermal effect, while closer to the wall, the wake processes strongly modulate this reduction. Laterally, the turbines’ rotation promotes asymmetry, while stability opposes this tendency. The longitudinal coherence, significantly reduced by the wake flows, is less affected by the boundary layer's thermal stability. - Open Access
- 24 April 2023
- Published by Springer Nature in Boundary-Layer Meteorology
- Vol. 188 (1) , 113-134
Some Further Aspects of Stable Boundary-Layer Simulation in a Stratified-Flow Wind Tunnel
It is demonstrated that the vertical profile of gradient Richardson number, Ri, can be shaped by control of the working-section inlet temperature profile. In previous work (Hancock and Hayden in Boundary-Layer Meteorol 168:20–57, 2018; 175:93–112, 2020; 180:5–26, 2021) the inlet temperature profile had been specified but without control of the profile of $$Ri$$ in the developed-flow region of the working section. Control of the inlet temperature profile is provided by 15 inlet heaters (spread uniformly across the height of the working section), allowing control of the temperature gradient over the bulk of the boundary layer, and the overall temperature level above that of the surface. The bulk Richardson number for the 11 cases covers the range 0.01–0.17 (there is no overlying inversion). In the upper $$\approx$$ 2/3 of the boundary layer the Reynolds stresses and turbulent heat flux are controlled by the gradient in mean temperature, while in the lower $$\approx$$ 1/3 they are controlled both by this gradient and by the level above the surface temperature. In three examples, $$Ri$$ is approximately constant at 0.07, 0.10 and 0.13 across the bulk of the layer. The previous observation of horizontally homogenous behaviour in the temperature profiles in the top $$\approx$$ 2/3 of the boundary layer but not in the lower $$\approx$$ 1/3 is repeated here, except when, tentatively, Ri does not exceed 0.05 over the bulk of the boundary layer. Favourable validation comparisons are made against two sets of local scaling systems and field data over the full depth of the boundary layer, over the range 0.006 $$\le Ri \le$$ 0.3, or, in terms of height and local Obukhov length, 0.005 $$\le z/L \le$$ 1.- 24 April 2023
- Published by Springer Nature in Boundary-Layer Meteorology
- Vol. 188 (1) , 113-134
Open AccessSome Further Aspects of Stable Boundary-Layer Simulation in a Stratified-Flow Wind Tunnel
It is demonstrated that the vertical profile of gradient Richardson number, Ri, can be shaped by control of the working-section inlet temperature profile. In previous work (Hancock and Hayden in Boundary-Layer Meteorol 168:20–57, 2018; 175:93–112, 2020; 180:5–26, 2021) the inlet temperature profile had been specified but without control of the profile of $$Ri$$ in the developed-flow region of the working section. Control of the inlet temperature profile is provided by 15 inlet heaters (spread uniformly across the height of the working section), allowing control of the temperature gradient over the bulk of the boundary layer, and the overall temperature level above that of the surface. The bulk Richardson number for the 11 cases covers the range 0.01–0.17 (there is no overlying inversion). In the upper $$\approx$$ 2/3 of the boundary layer the Reynolds stresses and turbulent heat flux are controlled by the gradient in mean temperature, while in the lower $$\approx$$ 1/3 they are controlled both by this gradient and by the level above the surface temperature. In three examples, $$Ri$$ is approximately constant at 0.07, 0.10 and 0.13 across the bulk of the layer. The previous observation of horizontally homogenous behaviour in the temperature profiles in the top $$\approx$$ 2/3 of the boundary layer but not in the lower $$\approx$$ 1/3 is repeated here, except when, tentatively, Ri does not exceed 0.05 over the bulk of the boundary layer. Favourable validation comparisons are made against two sets of local scaling systems and field data over the full depth of the boundary layer, over the range 0.006 $$\le Ri \le$$ 0.3, or, in terms of height and local Obukhov length, 0.005 $$\le z/L \le$$ 1. - Open Access
- 21 April 2021
- Published by Springer Nature in Boundary-Layer Meteorology
- Vol. 180 (1) , 5-26
Wind-Tunnel Simulation of Approximately Horizontally Homogeneous Stable Atmospheric Boundary Layers
Two cases of an overlying inversion imposed on a stable boundary layer are investigated, extending the work of Hancock and Hayden (Boundary-Layer Meteorol 168:29–57, 2018; 175:93–112, 2020). Vertical profiles of Reynolds stresses and heat flux show closely horizontally homogeneous behaviour over a streamwise fetch of more than eight boundary-layer heights. However, profiles of mean temperature and velocity show closely horizontally homogeneous behaviour only in the top two-thirds of the boundary layer. In the lower one-third the temperature decreases with fetch, directly as a consequence of heat transfer to the surface. A weaker effect is seen in the mean velocity profiles, curiously, such that the gradient Richardson number is invariant with fetch, while various other quantities are not. Stability leads to a ‘blocking’ of vertical influence. Inferred aerodynamic and thermal roughness lengths increase with fetch, while the former is constant in the neutral case, as expected. Favourable validation comparisons are made against two sets of local-scaling systems over the full depth of the boundary layer. Close concurrence is seen for all stable cases for z/L < 0.2, where z and L are the vertical height and local Obukhov length, respectively, and over most of the layer for some quantities.
- 21 April 2021
- Published by Springer Nature in Boundary-Layer Meteorology
- Vol. 180 (1) , 5-26
Open AccessWind-Tunnel Simulation of Approximately Horizontally Homogeneous Stable Atmospheric Boundary Layers
Two cases of an overlying inversion imposed on a stable boundary layer are investigated, extending the work of Hancock and Hayden (Boundary-Layer Meteorol 168:29–57, 2018; 175:93–112, 2020). Vertical profiles of Reynolds stresses and heat flux show closely horizontally homogeneous behaviour over a streamwise fetch of more than eight boundary-layer heights. However, profiles of mean temperature and velocity show closely horizontally homogeneous behaviour only in the top two-thirds of the boundary layer. In the lower one-third the temperature decreases with fetch, directly as a consequence of heat transfer to the surface. A weaker effect is seen in the mean velocity profiles, curiously, such that the gradient Richardson number is invariant with fetch, while various other quantities are not. Stability leads to a ‘blocking’ of vertical influence. Inferred aerodynamic and thermal roughness lengths increase with fetch, while the former is constant in the neutral case, as expected. Favourable validation comparisons are made against two sets of local-scaling systems over the full depth of the boundary layer. Close concurrence is seen for all stable cases for z/L < 0.2, where z and L are the vertical height and local Obukhov length, respectively, and over most of the layer for some quantities.
- Open Access
- 3 January 2020
- Published by Springer Nature in Boundary-Layer Meteorology
- Vol. 175 (1) , 93-112
Wind-Tunnel Simulation of Stable Atmospheric Boundary Layers with an Overlying Inversion
Four cases of an overlying inversion imposed on a stable boundary layer are investigated, extending the earlier work of Hancock and Hayden (Boundary-Layer Meteorol 168:29–57, 2018), where no inversion was imposed. The inversion is imposed to one or other of two depths within the layer: midway or deep. Four cases of changed surface condition are also investigated, and it is seen that the surface and imposed conditions behave independently. A change of imposed inversion condition leaves the bottom 1/3 of the layer almost completely unaffected; a change of the surface condition leaves the top 2/3 unaffected. Comparisons are made against two sets of local-scaling systems over the full height of the boundary layer. Both show some influence of the inversion condition. The surface heat flux and the reduction in surface shear stress, and hence the ratio of the boundary-layer height to surface Obukhov length, are determined by the temperature difference across the surface layer (not the whole layer), bringing all cases together in single correlations as functions of a surface-layer bulk Richardson number.
- 3 January 2020
- Published by Springer Nature in Boundary-Layer Meteorology
- Vol. 175 (1) , 93-112
Open AccessWind-Tunnel Simulation of Stable Atmospheric Boundary Layers with an Overlying Inversion
Four cases of an overlying inversion imposed on a stable boundary layer are investigated, extending the earlier work of Hancock and Hayden (Boundary-Layer Meteorol 168:29–57, 2018), where no inversion was imposed. The inversion is imposed to one or other of two depths within the layer: midway or deep. Four cases of changed surface condition are also investigated, and it is seen that the surface and imposed conditions behave independently. A change of imposed inversion condition leaves the bottom 1/3 of the layer almost completely unaffected; a change of the surface condition leaves the top 2/3 unaffected. Comparisons are made against two sets of local-scaling systems over the full height of the boundary layer. Both show some influence of the inversion condition. The surface heat flux and the reduction in surface shear stress, and hence the ratio of the boundary-layer height to surface Obukhov length, are determined by the temperature difference across the surface layer (not the whole layer), bringing all cases together in single correlations as functions of a surface-layer bulk Richardson number.
- Open Access
- 21 February 2018
- Published by Springer Nature in Boundary-Layer Meteorology
- Vol. 168 (1) , 29-57
Wind-Tunnel Simulation of Weakly and Moderately Stable Atmospheric Boundary Layers
The simulation of horizontally homogeneous boundary layers that have characteristics of weakly and moderately stable atmospheric flow is investigated, where the well-established wind engineering practice of using ‘flow generators’ to provide a deep boundary layer is employed. Primary attention is given to the flow above the surface layer, in the absence of an overlying inversion, as assessed from first- and second-order moments of velocity and temperature. A uniform inlet temperature profile ahead of a deep layer, allowing initially neutral flow, results in the upper part of the boundary layer remaining neutral. A non-uniform inlet temperature profile is required but needs careful specification if odd characteristics are to be avoided, attributed to long-lasting effects inherent of stability, and to a reduced level of turbulent mixing. The first part of the wind-tunnel floor must not be cooled if turbulence quantities are to vary smoothly with height. Closely horizontally homogeneous flow is demonstrated, where profiles are comparable or closely comparable with atmospheric data in terms of local similarity and functions of normalized height. The ratio of boundary-layer height to surface Obukhov length, and the surface heat flux, are functions of the bulk Richardson number, independent of horizontal homogeneity. Surface heat flux rises to a maximum and then decreases.
- 21 February 2018
- Published by Springer Nature in Boundary-Layer Meteorology
- Vol. 168 (1) , 29-57
Open AccessWind-Tunnel Simulation of Weakly and Moderately Stable Atmospheric Boundary Layers
The simulation of horizontally homogeneous boundary layers that have characteristics of weakly and moderately stable atmospheric flow is investigated, where the well-established wind engineering practice of using ‘flow generators’ to provide a deep boundary layer is employed. Primary attention is given to the flow above the surface layer, in the absence of an overlying inversion, as assessed from first- and second-order moments of velocity and temperature. A uniform inlet temperature profile ahead of a deep layer, allowing initially neutral flow, results in the upper part of the boundary layer remaining neutral. A non-uniform inlet temperature profile is required but needs careful specification if odd characteristics are to be avoided, attributed to long-lasting effects inherent of stability, and to a reduced level of turbulent mixing. The first part of the wind-tunnel floor must not be cooled if turbulence quantities are to vary smoothly with height. Closely horizontally homogeneous flow is demonstrated, where profiles are comparable or closely comparable with atmospheric data in terms of local similarity and functions of normalized height. The ratio of boundary-layer height to surface Obukhov length, and the surface heat flux, are functions of the bulk Richardson number, independent of horizontal homogeneity. Surface heat flux rises to a maximum and then decreases.
- 26 May 2015
- Published by Springer Nature in Boundary-Layer Meteorology
- Vol. 156 (3) , 395-413
A Wind-Tunnel Simulation of the Wake of a Large Wind Turbine in a Weakly Unstable Boundary Layer
- 26 May 2015
- Published by Springer Nature in Boundary-Layer Meteorology
- Vol. 156 (3) , 395-413
A Wind-Tunnel Simulation of the Wake of a Large Wind Turbine in a Weakly Unstable Boundary Layer
- Open Access
- 16 December 2014
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 555 (1) , 012047
Wind tunnel simulation of a wind turbine wake in neutral, stable and unstable wind flow
Measurements of mean velocity, Reynolds stresses, temperature and heat flux have been made in the wake of a model wind turbine in the EnFlo meteorology wind tunnel, for three atmospheric boundary layer states: the base-line neutral case, stable and unstable. The full-to-model scale is approximately 300:1. Primary instrumentation is two-component LDA combine with cold-wire thermometry to measure heat flux. In terms of surface conditions, the stratified cases are weak, but there is a strong 'imposed' condition in the stable case. The measurements were made between 0.5D and 10D, where D is the turbine disk diameter. In the stable case the velocity deficit decreases more slowly; more quickly in the unstable case. Heights at which quantities are maximum or minimum are greater in the unstable case and smaller in the stable case. In the stable case the wake height is suppressed but the width is increased, while in the unstable case the height is increased and the width (at hub height) reaches a maximum and then decreases. The turbulence in the wake behaves in a complex way. Further work needs to be done, to cover stronger levels of surface condition, requiring more extensive measurements to properly capture the wake development.
- 16 December 2014
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 555 (1) , 012047
Open AccessWind tunnel simulation of a wind turbine wake in neutral, stable and unstable wind flow
Measurements of mean velocity, Reynolds stresses, temperature and heat flux have been made in the wake of a model wind turbine in the EnFlo meteorology wind tunnel, for three atmospheric boundary layer states: the base-line neutral case, stable and unstable. The full-to-model scale is approximately 300:1. Primary instrumentation is two-component LDA combine with cold-wire thermometry to measure heat flux. In terms of surface conditions, the stratified cases are weak, but there is a strong 'imposed' condition in the stable case. The measurements were made between 0.5D and 10D, where D is the turbine disk diameter. In the stable case the velocity deficit decreases more slowly; more quickly in the unstable case. Heights at which quantities are maximum or minimum are greater in the unstable case and smaller in the stable case. In the stable case the wake height is suppressed but the width is increased, while in the unstable case the height is increased and the width (at hub height) reaches a maximum and then decreases. The turbulence in the wake behaves in a complex way. Further work needs to be done, to cover stronger levels of surface condition, requiring more extensive measurements to properly capture the wake development.
- 1 January 2014
- Published by Springer Nature
- p. 109-114
Wind Tunnel Simulation of Wind Turbine Wakes in Neutral, Stable and Unstable Offshore Atmospheric Boundary Layers
- 1 January 2014
- Published by Springer Nature
- p. 109-114
Wind Tunnel Simulation of Wind Turbine Wakes in Neutral, Stable and Unstable Offshore Atmospheric Boundary Layers
- 27 December 2013
- Published by Springer Nature in Boundary-Layer Meteorology
- Vol. 151 (1) , 3-21
Wind-Tunnel Simulation of the Wake of a Large Wind Turbine in a Stable Boundary Layer. Part 1: The Boundary-Layer Simulation
- 27 December 2013
- Published by Springer Nature in Boundary-Layer Meteorology
- Vol. 151 (1) , 3-21
Wind-Tunnel Simulation of the Wake of a Large Wind Turbine in a Stable Boundary Layer. Part 1: The Boundary-Layer Simulation