Zachary Grasley
Research Subjects
Zachary Grasley has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Christa E. Torrence
Department of Materials Science and Engineering, Texas A&M University, College Station, USA
5 shared publications - Aishwarya Baranikumar
Virginia Department of Transportation, Maintenance Division, Richmond, VA
4 shared publications - Jeffrey W. Bullard
Materials and Structural Systems Division Engineering Laboratory National Institute of Standards and Technology Gaithersburg Maryland
3 shared publications Edward Garboczi
National Institute of Standards and Technology, Boulder, CO, USA
2 shared publicationsK.R. Rajagopal
J. Mike Walker ‘66 Department of Mechanical Engineering, Texas A&M University, College Station, TX, USA
2 shared publications- Pavitra Tejaswi Murru
Texas A&M University, College Station, TX, USA
2 shared publications
Latest Publications
- 24 August 2026
- Published by Elsevier in Journal of Cleaner Production
- Vol. 575
Sustainability assessment of concrete pavement overlays reinforced with hybrid recycled and manufactured steel fibers
- 24 August 2026
- Published by Elsevier in Journal of Cleaner Production
- Vol. 575
Sustainability assessment of concrete pavement overlays reinforced with hybrid recycled and manufactured steel fibers
- Open Access
Development of Test Methods to Evaluate the Printability of Concrete Materials for Additive Manufacturing
This study proposes test methods for assessing the printability of concrete materials for Additive Manufacturing. The printability of concrete is divided into three main aspects: flowability, setting time, and buildability. These properties are considered to monitor the critical quality of 3DCP and to ensure a successful print. Flowability is evaluated through a rheometer test, where the evolution of shear yield strength is monitored at a constant rate (rpm), similar to the printer setup. Flowability limits were set based on the user-defined maximum thickness of a printed layer and the onset of gaps/cracks during printing. Setting time is evaluated through an ultrasonic wave pulse velocity test (UPV), where the first inflection point of the evolution of the UPV graph corresponds to the setting time of the concrete specimen. The results from this continuous non-destructive test were found to correlate with the results from the discrete destructive ASTM C-191 test for measuring setting time with a maximum difference of 5% between both sets of values. Lastly, buildability was evaluated through the measurement of the early-age compressive strength of concrete, and a correlation with the UPV results obtained a predictive model that can be used in real-time to non-destructively assess the material buildability. This predictive model had a maximum percentage difference of 13% with the measured values. The outcome of this study is a set of tests to evaluate the properties of 3D printable concrete (3DP) material and provide a basis for a framework to benchmark and design materials for additive manufacturing.
Open AccessDevelopment of Test Methods to Evaluate the Printability of Concrete Materials for Additive Manufacturing
This study proposes test methods for assessing the printability of concrete materials for Additive Manufacturing. The printability of concrete is divided into three main aspects: flowability, setting time, and buildability. These properties are considered to monitor the critical quality of 3DCP and to ensure a successful print. Flowability is evaluated through a rheometer test, where the evolution of shear yield strength is monitored at a constant rate (rpm), similar to the printer setup. Flowability limits were set based on the user-defined maximum thickness of a printed layer and the onset of gaps/cracks during printing. Setting time is evaluated through an ultrasonic wave pulse velocity test (UPV), where the first inflection point of the evolution of the UPV graph corresponds to the setting time of the concrete specimen. The results from this continuous non-destructive test were found to correlate with the results from the discrete destructive ASTM C-191 test for measuring setting time with a maximum difference of 5% between both sets of values. Lastly, buildability was evaluated through the measurement of the early-age compressive strength of concrete, and a correlation with the UPV results obtained a predictive model that can be used in real-time to non-destructively assess the material buildability. This predictive model had a maximum percentage difference of 13% with the measured values. The outcome of this study is a set of tests to evaluate the properties of 3D printable concrete (3DP) material and provide a basis for a framework to benchmark and design materials for additive manufacturing.
- Open Access
- 23 February 2022
- Published by Springer Nature in Materials and Structures
- Vol. 55 (2) , 1
Correction to: Temperature dependence of viscoelastic Poisson’s ratio of cement mortar
- 23 February 2022
- Published by Springer Nature in Materials and Structures
- Vol. 55 (2) , 1
Open AccessCorrection to: Temperature dependence of viscoelastic Poisson’s ratio of cement mortar
- Retraction
- 1 October 2021
- Published by Elsevier in Construction and Building Materials
- Vol. 304, 124704
Retraction notice to “Experimental investigation and comparative machine-learning prediction of strength behavior of optimized recycled rubber concrete” [JCBM 256 (2020) 119478]
- 1 October 2021
- Published by Elsevier in Construction and Building Materials
- Vol. 304, 124704
RetractionRetraction notice to “Experimental investigation and comparative machine-learning prediction of strength behavior of optimized recycled rubber concrete” [JCBM 256 (2020) 119478]
- Retraction
- 1 October 2021
- Published by Elsevier in Construction and Building Materials
- Vol. 304, 124711
Retraction notice to “Strength and dynamic elasticity modulus of rubberized concrete designed with ANFIS modeling and ultrasonic technique” [J. Constr. Build. Mater. 240 (2019) 117920]
- 1 October 2021
- Published by Elsevier in Construction and Building Materials
- Vol. 304, 124711
RetractionRetraction notice to “Strength and dynamic elasticity modulus of rubberized concrete designed with ANFIS modeling and ultrasonic technique” [J. Constr. Build. Mater. 240 (2019) 117920]
- 1 September 2021
- Published by Elsevier in Cement and Concrete Research
- Vol. 147, 106522
Estimating viscoelastic compliance of desiccating cementitious materials using drying prism tests
- 1 September 2021
- Published by Elsevier in Cement and Concrete Research
- Vol. 147, 106522
Estimating viscoelastic compliance of desiccating cementitious materials using drying prism tests
- Open Access
- 19 April 2021
- Published by Springer Nature in Materials and Structures
- Vol. 54 (3) , 1-13
Temperature dependence of viscoelastic Poisson’s ratio of cement mortar
Concrete creep research has focused primarily on uniaxial response. However, biaxially prestressed concrete structures are common, resulting in a multiaxial stress state that can complicate the behavior of a viscoelastic material like concrete. Significant creep strains may be induced in directions transverse to each principle stress due to Poisson’s effect. Past research is unclear regarding the viscoelastic or viscoplastic properties of concrete outside of uniaxial response. It has been reported in separate studies that concrete viscoelastic/viscoplastic Poisson’s ratio (VPR) is an increasing, decreasing and constant function with time, with all reported measurements performed at room temperature. In this paper, the 3D basic creep response of mature cement mortar is examined using a confined compression experiment that allows direct determination of the full stress and infinitesimal strain tensors in a single test, which enables the determination of VPR under a multiaxial stress state. For this purpose, a unique, miniature version of the standardized concrete creep frame is designed that is amenable to placing in climate chambers and temperature ovens. The experimental results indicate that the VPR of sealed, mature cement mortar is nearly constant and equal to the elastic at room temperature, while the VPR gradually increases with time when measured at 60 °C.
- 19 April 2021
- Published by Springer Nature in Materials and Structures
- Vol. 54 (3) , 1-13
Open AccessTemperature dependence of viscoelastic Poisson’s ratio of cement mortar
Concrete creep research has focused primarily on uniaxial response. However, biaxially prestressed concrete structures are common, resulting in a multiaxial stress state that can complicate the behavior of a viscoelastic material like concrete. Significant creep strains may be induced in directions transverse to each principle stress due to Poisson’s effect. Past research is unclear regarding the viscoelastic or viscoplastic properties of concrete outside of uniaxial response. It has been reported in separate studies that concrete viscoelastic/viscoplastic Poisson’s ratio (VPR) is an increasing, decreasing and constant function with time, with all reported measurements performed at room temperature. In this paper, the 3D basic creep response of mature cement mortar is examined using a confined compression experiment that allows direct determination of the full stress and infinitesimal strain tensors in a single test, which enables the determination of VPR under a multiaxial stress state. For this purpose, a unique, miniature version of the standardized concrete creep frame is designed that is amenable to placing in climate chambers and temperature ovens. The experimental results indicate that the VPR of sealed, mature cement mortar is nearly constant and equal to the elastic at room temperature, while the VPR gradually increases with time when measured at 60 °C.
- 8 March 2021
- Published by Springer Nature in Mechanics of Time-Dependent Materials
- Vol. 26 (2) , 289-307
Thermorheological approach to predict long-term creep of cement mortar from short-term tests
- 8 March 2021
- Published by Springer Nature in Mechanics of Time-Dependent Materials
- Vol. 26 (2) , 289-307
Thermorheological approach to predict long-term creep of cement mortar from short-term tests
- 23 July 2020
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 23 (4) , 1161-1174
Density-driven damage mechanics (D3-M) model for concrete I: mechanical damage
Damage in concrete has been modelled using various approaches such as fracture mechanics, continuum damage mechanics and failure envelope theories. This study proposes a new approach to model the initiation of damage in concrete that addresses some limitations associated with the existing approaches. The proposed approach defines damage in terms of changes in the density of the material at the microscopic level, where such changes are induced by mechanical loading. The suggested approach is used to simulate the response of 2D concrete bodies to uni-axial tension and uni-axial compression. The simulation results indicate that the proposed model, by means of a single constitutive function, is able to correctly predict failure patterns and aptly capture the damage mechanisms under both uni-axial tension and uni-axial compression loadings using only the information related to the microstructure, the density field and the stiffness field. As a continuation, in Part II, the ability of the D3-M approach to model fully coupled chemo-mechanical damage in concrete using a single constitutive equation will be demonstrated.
- 23 July 2020
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 23 (4) , 1161-1174
Density-driven damage mechanics (D3-M) model for concrete I: mechanical damage
Damage in concrete has been modelled using various approaches such as fracture mechanics, continuum damage mechanics and failure envelope theories. This study proposes a new approach to model the initiation of damage in concrete that addresses some limitations associated with the existing approaches. The proposed approach defines damage in terms of changes in the density of the material at the microscopic level, where such changes are induced by mechanical loading. The suggested approach is used to simulate the response of 2D concrete bodies to uni-axial tension and uni-axial compression. The simulation results indicate that the proposed model, by means of a single constitutive function, is able to correctly predict failure patterns and aptly capture the damage mechanisms under both uni-axial tension and uni-axial compression loadings using only the information related to the microstructure, the density field and the stiffness field. As a continuation, in Part II, the ability of the D3-M approach to model fully coupled chemo-mechanical damage in concrete using a single constitutive equation will be demonstrated.
- 23 July 2020
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 23 (4) , 1175-1185
Density driven damage mechanics (D3-M) model for concrete II: fully coupled chemo-mechanical damage
In Part I, a density driven damage mechanics (D3-M) approach and its application to model mechanical damage in concrete are presented. In this study, chemical and chemo-mechanical damage in concrete were modelled using the D3-M approach. It is proposed that reductions in local density in certain regions, created when concrete is subjected to chemical attack or coupled chemical-mechanical loading, result in reduced stiffness and strength of the material. The D3-M modelling approach stands out among the past efforts to predict the response of concrete to mechanical and chemical stimuli due to its ability to effectively model the mechanical, chemical, and coupled mechanical-chemical responses of concrete using a consistent framework and a single constitutive equation for both types of damage. Model simulations indicate that the response of the material to a scenario where chemical and mechanical loads are acting simultaneously cannot be considered equivalent to the response obtained by superposing the separate responses to independent mechanical and chemical loads.
- 23 July 2020
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 23 (4) , 1175-1185
Density driven damage mechanics (D3-M) model for concrete II: fully coupled chemo-mechanical damage
In Part I, a density driven damage mechanics (D3-M) approach and its application to model mechanical damage in concrete are presented. In this study, chemical and chemo-mechanical damage in concrete were modelled using the D3-M approach. It is proposed that reductions in local density in certain regions, created when concrete is subjected to chemical attack or coupled chemical-mechanical loading, result in reduced stiffness and strength of the material. The D3-M modelling approach stands out among the past efforts to predict the response of concrete to mechanical and chemical stimuli due to its ability to effectively model the mechanical, chemical, and coupled mechanical-chemical responses of concrete using a consistent framework and a single constitutive equation for both types of damage. Model simulations indicate that the response of the material to a scenario where chemical and mechanical loads are acting simultaneously cannot be considered equivalent to the response obtained by superposing the separate responses to independent mechanical and chemical loads.