Sharifah Fatmadiana Wan Muhamad Hatta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Sharifah Fatmadiana Wan Muhamad Hatta has a total of 132 co-authors. Here are the top co-authors by number of shared publications:
- Norhayati Soin
University of Malaya
11 shared publications Norhayati Soin
Department of Electrical Engineering, Faculty of Engineering, Universiti Malaya, Kuala Lumpur, Malaysia
7 shared publicationsN. Soin
Centre of Printable Electronics, Universiti Malaya, Kuala Lumpur, Malaysia
6 shared publicationsFazliyatul Azwa Md Rezali
Taylor’s University
5 shared publications- Yasmin Abdul Wahab
Universiti Malaya
5 shared publications - Mohammad Aminul Islam
Department of Electrical Engineering, Faculty of Engineering, Universiti Malaya, Kuala Lumpur, Malaysia
4 shared publications
Latest Publications
- 13 October 2026
- Published by American Chemical Society (ACS) in ACS Sensors
- Vol. 11 (10) , 8813-8838
AI-Enhanced Wearable Glucose Sensors: From Intelligent Sensing to Closed-Loop Management of Diabetes
Wearable glucose sensors enable continuous monitoring of glycemic dynamics, yet their clinical utility is constrained by signal instability, physiological delay, and limited predictive capability. Artificial intelligence (AI) has been increasingly integrated to address these limitations. This review summarizes recent advances in AI-enhanced wearable glucose sensors, with a focus on the evolution of sensing technologies and the role of AI across three main aspects: calibration, glucose prediction, and wearable closed-loop control. In calibration, AI-based approaches for improving short-term signal reliability and compensating long-term drift are reviewed. In prediction, methods ranging from continuous glucose monitoring (CGM)-based forecasting to multimodal sensor fusion and noninvasive sensing are summarized, including both continuous glucose estimation and event-oriented detection of hypo- and hyperglycemia. The integration of sensing, prediction, and insulin delivery in wearable closed-loop artificial pancreas is also discussed. Finally, the remaining challenges and future directions are discussed, highlighting the potential of AI-enhanced wearable glucose sensors to support more reliable and integrated diabetes management.
- 13 October 2026
- Published by American Chemical Society (ACS) in ACS Sensors
- Vol. 11 (10) , 8813-8838
AI-Enhanced Wearable Glucose Sensors: From Intelligent Sensing to Closed-Loop Management of Diabetes
Wearable glucose sensors enable continuous monitoring of glycemic dynamics, yet their clinical utility is constrained by signal instability, physiological delay, and limited predictive capability. Artificial intelligence (AI) has been increasingly integrated to address these limitations. This review summarizes recent advances in AI-enhanced wearable glucose sensors, with a focus on the evolution of sensing technologies and the role of AI across three main aspects: calibration, glucose prediction, and wearable closed-loop control. In calibration, AI-based approaches for improving short-term signal reliability and compensating long-term drift are reviewed. In prediction, methods ranging from continuous glucose monitoring (CGM)-based forecasting to multimodal sensor fusion and noninvasive sensing are summarized, including both continuous glucose estimation and event-oriented detection of hypo- and hyperglycemia. The integration of sensing, prediction, and insulin delivery in wearable closed-loop artificial pancreas is also discussed. Finally, the remaining challenges and future directions are discussed, highlighting the potential of AI-enhanced wearable glucose sensors to support more reliable and integrated diabetes management.
- Open Access
- 12 October 2026
- Published by IOP Publishing in Flexible and Printed Electronics
- Vol. 11 (4) , 045002
Synergistic Li + -functionalized Mo 2 CT X MXene and polyaniline composite for rapid and stable moisture sensing in wearable wound monitoring application
Managing optimal moisture balance is essential for chronic wound healing, yet current clinical assessments are often subjective and intermittent. This study reports the development of a high-performance, flexible resistive moisture sensor designed for real-time, quantitative wound monitoring. The active sensing layer consists of a lithium-ion (Li + ) functionalized Mo 2 CT X MXene and polyaniline (PANI) composite. Li + intercalation was utilized to expand the MXene interlayer spacing, enhancing water adsorption and ion transport. Simultaneously, in situ polymerized PANI was introduced to provide stable proton-conductive pathways. Current–voltage characterization verified that the Li + –Mo 2 CT X /PANI composite forms robust Ohmic contacts with the electrodes, exhibiting over a 40-fold enhancement in baseline electrical conductance compared to pristine Mo 2 CT X . The composite was integrated onto screen-printed circular interdigitated electrodes on a flexible PET substrate and encapsulated with poly(diallyldimethylammonium chloride) (PDAC). This protective PDAC layer acts as a semi-permeable moisture-diffusion barrier that regulates water molecule transport, prevents surface fouling and uncontrolled hydration saturation, and ensures environmental stability without compromising response speed. The sensor demonstrates a linear response across a wide relative humidity (RH) range of 20%–80%, featuring sensitivity of approximately 2.0 Δ R /%ΔRH, with a rapid response time of ∼1 s and a recovery time of ∼11 s. The device demonstrates high mechanical flexibility, and stable operation over a 15 d period. Real-time assessments using finger-touch tests and PVA-hydrogel wound models successfully distinguished between dry, normal, and wet clinical states. The superior performance is attributed to the synergistic effects of Li + -assisted interlayer hydration, Grotthuss-type proton hopping, and moisture-induced PANI protonation. These findings position the Li + –Mo 2 CT X /PANI composite as a promising candidate for next-generation smart dressings in digital wound management.
- 12 October 2026
- Published by IOP Publishing in Flexible and Printed Electronics
- Vol. 11 (4) , 045002
Open AccessSynergistic Li + -functionalized Mo 2 CT X MXene and polyaniline composite for rapid and stable moisture sensing in wearable wound monitoring application
Managing optimal moisture balance is essential for chronic wound healing, yet current clinical assessments are often subjective and intermittent. This study reports the development of a high-performance, flexible resistive moisture sensor designed for real-time, quantitative wound monitoring. The active sensing layer consists of a lithium-ion (Li + ) functionalized Mo 2 CT X MXene and polyaniline (PANI) composite. Li + intercalation was utilized to expand the MXene interlayer spacing, enhancing water adsorption and ion transport. Simultaneously, in situ polymerized PANI was introduced to provide stable proton-conductive pathways. Current–voltage characterization verified that the Li + –Mo 2 CT X /PANI composite forms robust Ohmic contacts with the electrodes, exhibiting over a 40-fold enhancement in baseline electrical conductance compared to pristine Mo 2 CT X . The composite was integrated onto screen-printed circular interdigitated electrodes on a flexible PET substrate and encapsulated with poly(diallyldimethylammonium chloride) (PDAC). This protective PDAC layer acts as a semi-permeable moisture-diffusion barrier that regulates water molecule transport, prevents surface fouling and uncontrolled hydration saturation, and ensures environmental stability without compromising response speed. The sensor demonstrates a linear response across a wide relative humidity (RH) range of 20%–80%, featuring sensitivity of approximately 2.0 Δ R /%ΔRH, with a rapid response time of ∼1 s and a recovery time of ∼11 s. The device demonstrates high mechanical flexibility, and stable operation over a 15 d period. Real-time assessments using finger-touch tests and PVA-hydrogel wound models successfully distinguished between dry, normal, and wet clinical states. The superior performance is attributed to the synergistic effects of Li + -assisted interlayer hydration, Grotthuss-type proton hopping, and moisture-induced PANI protonation. These findings position the Li + –Mo 2 CT X /PANI composite as a promising candidate for next-generation smart dressings in digital wound management.
- 21 July 2026
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 37 (20) , 1614
A wearable zigzag strain sensor based on screen-printed GNPs-PDMS composites for real-time human motion monitoring
- 21 July 2026
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 37 (20) , 1614
A wearable zigzag strain sensor based on screen-printed GNPs-PDMS composites for real-time human motion monitoring
- 2 June 2026
- Published by SAGE Publications in Journal of Composite Materials
Modeling percolation transition in carbon black/CNT conductive composites using a probability-reconstructed Bruggeman approach
A probability-informed reconstructed Bruggeman effective medium framework is developed to model the percolation transition in carbon black (CB), carbon nanotube (CNT), and hybrid CB/CNT conductive systems. In contrast to deterministic volume-fraction weighting, the formulation introduces statistically defined overlap, contact, and tunneling probabilities derived from a Poisson double-coverage assumption. Preliminary compaction experiments, on dried fillers provide conductivity–volume fraction relations that are accurately described by sigmoid functions (R 2 = 0.998 for CNT and 0.996 for CB). Inverse reconstruction of the Bruggeman equation yields a concentration-dependent mixing function α ( ϕ ) , demonstrating that the macroscopic percolation transition corresponds to a rapid redistribution of conductive-event dominance from tunneling-controlled to contact-controlled transport. Finite-element simulations incorporating a continuous spatial volume-fraction field ϕ ( x , y , z ) with an adjustable fluctuation amplitude parameter K uni = 0.01 -0.09, further reveal that increasing fluctuation amplitude, promotes an earlier onset of percolation behavior, occurring before the equivalence of contact probabilities and tunneling probabilities ( ϕ ≈ 0.10 for CNT and 0.13 for CB). In hybrid systems under parallel coupling, increasing CNT loading (0–0.04) raises baseline conductivity by ∼2 orders of magnitude at low CB content (0–0.6), while convergence occurs at high CB fractions where CB-dominated transport saturates at 1 S/m. The proposed framework provides a computationally efficient and experimentally calibrated predictive tool for designing conductive polymer composites, with direct applicability to flexible electronics, EMI shielding, and antistatic coatings.
- 2 June 2026
- Published by SAGE Publications in Journal of Composite Materials
Modeling percolation transition in carbon black/CNT conductive composites using a probability-reconstructed Bruggeman approach
A probability-informed reconstructed Bruggeman effective medium framework is developed to model the percolation transition in carbon black (CB), carbon nanotube (CNT), and hybrid CB/CNT conductive systems. In contrast to deterministic volume-fraction weighting, the formulation introduces statistically defined overlap, contact, and tunneling probabilities derived from a Poisson double-coverage assumption. Preliminary compaction experiments, on dried fillers provide conductivity–volume fraction relations that are accurately described by sigmoid functions (R 2 = 0.998 for CNT and 0.996 for CB). Inverse reconstruction of the Bruggeman equation yields a concentration-dependent mixing function α ( ϕ ) , demonstrating that the macroscopic percolation transition corresponds to a rapid redistribution of conductive-event dominance from tunneling-controlled to contact-controlled transport. Finite-element simulations incorporating a continuous spatial volume-fraction field ϕ ( x , y , z ) with an adjustable fluctuation amplitude parameter K uni = 0.01 -0.09, further reveal that increasing fluctuation amplitude, promotes an earlier onset of percolation behavior, occurring before the equivalence of contact probabilities and tunneling probabilities ( ϕ ≈ 0.10 for CNT and 0.13 for CB). In hybrid systems under parallel coupling, increasing CNT loading (0–0.04) raises baseline conductivity by ∼2 orders of magnitude at low CB content (0–0.6), while convergence occurs at high CB fractions where CB-dominated transport saturates at 1 S/m. The proposed framework provides a computationally efficient and experimentally calibrated predictive tool for designing conductive polymer composites, with direct applicability to flexible electronics, EMI shielding, and antistatic coatings.
- 6 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (6) , 7989-7996
Screen-Printed Organic Electrochemical Transistor With 3-D-Printed Hollow Microneedle for a Fully Integrated Glucose Sensor
In this work, a novel fully integrated glucose sensor based on organic electrochemical transistor (OECT) has been proposed through feasible printing on a flexible substrate. The fully integrated glucose sensor incorporates: 1) a screen-printed OECT featuring poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) channel functionalized with a chitosan–titanium dioxide (CS-TiO₂) nanocomposite and glucose oxidase (GOx) enzyme to enable glucose detection; 2) a 3D-printed 3x3 hollow microneedle (HMN) platform with reservoir pad for minimally invasive sampling; and 3) a flexible compact wireless interfacing circuit for glucose analysis. Mechanical and electrical stability are investigated on the OECT device after 100 bending cycles and over a week of testing on a curved surface. With respect to glucose, the OECT showed a strong linear response in between 0.01 to 30 mM (r² = 0.993), a high sensitivity of 6.01 μA·mM⁻¹·cm⁻², and good selectivity against ascorbic acid and uric acid. Upon integration, the integrated glucose sensor achieved a rapid response time of under 20 s when tested on an agar gel-based skin model. The output currents were calibrated and then verified within the glucose range of 1–10 mM, with a total reading time of less than 120 s, demonstrating good accuracy. Overall, the implementation of OECT coupled with HMN offers a promising platform for a fully integrated glucose sensor, with great potential towards commercialization.
- 6 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (6) , 7989-7996
Screen-Printed Organic Electrochemical Transistor With 3-D-Printed Hollow Microneedle for a Fully Integrated Glucose Sensor
In this work, a novel fully integrated glucose sensor based on organic electrochemical transistor (OECT) has been proposed through feasible printing on a flexible substrate. The fully integrated glucose sensor incorporates: 1) a screen-printed OECT featuring poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) channel functionalized with a chitosan–titanium dioxide (CS-TiO₂) nanocomposite and glucose oxidase (GOx) enzyme to enable glucose detection; 2) a 3D-printed 3x3 hollow microneedle (HMN) platform with reservoir pad for minimally invasive sampling; and 3) a flexible compact wireless interfacing circuit for glucose analysis. Mechanical and electrical stability are investigated on the OECT device after 100 bending cycles and over a week of testing on a curved surface. With respect to glucose, the OECT showed a strong linear response in between 0.01 to 30 mM (r² = 0.993), a high sensitivity of 6.01 μA·mM⁻¹·cm⁻², and good selectivity against ascorbic acid and uric acid. Upon integration, the integrated glucose sensor achieved a rapid response time of under 20 s when tested on an agar gel-based skin model. The output currents were calibrated and then verified within the glucose range of 1–10 mM, with a total reading time of less than 120 s, demonstrating good accuracy. Overall, the implementation of OECT coupled with HMN offers a promising platform for a fully integrated glucose sensor, with great potential towards commercialization.
- Open Access
- 1 February 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (3) , 035330
Hybrid organic-inorganic electrolytes via SiO 2 -doping: enhanced stability and ionic conductivity for neuromorphic EGTs
Hybrid organic–inorganic electrolytes represent a promising class of materials for sustainable and energy-efficient electronics, yet strategies to simultaneously improve their electrochemical robustness and functional device performance remain limited. Here, a chitosan-silica hybrid electrolyte was developed by incorporating silica nanoparticles (SiO 2 NPs, 0–2 wt%) into a chitosan matrix, and its structural, electrochemical, and dielectric properties were systematically investigated. At an optimized SiO 2 NPs content of 1.5 wt%, the hybrid electrolyte achieved an ionic conductivity of 1.83 × 10 −5 S cm −1 and a high ion transference number ( t ion = 0.909), while the swelling rate was suppressed by 160% and the breakdown voltage was enhanced to 2.76 ± 0.013 V. These improvements were attributed to increased segmental mobility and Lewis acid–base interactions that promoted ion dissociation and stabilized electric double-layer formation. To demonstrate functional relevance, the chitosan-silica hybrid electrolyte was integrated into an electrolyte-gated transistor (EGT) with zinc oxide nanoparticles (ZnO NPs) channel, yielding reproducible synaptic neuromorphic characteristics, including excitatory post-synaptic current (EPSC) of 399.32 ± 42.36 nA and a paired-pulse facilitation (PPF) index of 90.4%. Importantly, this work establishes a direct correlation between nanoscale electrolyte engineering and neuromorphic device responses, using synaptic behaviors as functional validation of electrolyte stability and ionic transport. The findings establish chitosan-silica hybrids as promising materials for next-generation neuromorphic and biocompatible electronics.
- 1 February 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (3) , 035330
Open AccessHybrid organic-inorganic electrolytes via SiO 2 -doping: enhanced stability and ionic conductivity for neuromorphic EGTs
Hybrid organic–inorganic electrolytes represent a promising class of materials for sustainable and energy-efficient electronics, yet strategies to simultaneously improve their electrochemical robustness and functional device performance remain limited. Here, a chitosan-silica hybrid electrolyte was developed by incorporating silica nanoparticles (SiO 2 NPs, 0–2 wt%) into a chitosan matrix, and its structural, electrochemical, and dielectric properties were systematically investigated. At an optimized SiO 2 NPs content of 1.5 wt%, the hybrid electrolyte achieved an ionic conductivity of 1.83 × 10 −5 S cm −1 and a high ion transference number ( t ion = 0.909), while the swelling rate was suppressed by 160% and the breakdown voltage was enhanced to 2.76 ± 0.013 V. These improvements were attributed to increased segmental mobility and Lewis acid–base interactions that promoted ion dissociation and stabilized electric double-layer formation. To demonstrate functional relevance, the chitosan-silica hybrid electrolyte was integrated into an electrolyte-gated transistor (EGT) with zinc oxide nanoparticles (ZnO NPs) channel, yielding reproducible synaptic neuromorphic characteristics, including excitatory post-synaptic current (EPSC) of 399.32 ± 42.36 nA and a paired-pulse facilitation (PPF) index of 90.4%. Importantly, this work establishes a direct correlation between nanoscale electrolyte engineering and neuromorphic device responses, using synaptic behaviors as functional validation of electrolyte stability and ionic transport. The findings establish chitosan-silica hybrids as promising materials for next-generation neuromorphic and biocompatible electronics.
- Open Access
- 1 September 2025
- Published by IOP Publishing in Flexible and Printed Electronics
- Vol. 10 (3) , 035018
Direct functionalization of Mo2CT x MXene via single-step synthesis for printable, flexible, non-invasive moisture detection systems
A printable moisture sensor is an advanced device designed to measure water content in various materials, including soil, air, and other substances. The incorporation of K+ functionalization significantly increases the material’s hydrophilicity, promoting more effective adsorption and desorption of water molecules. This study explores the impact of MXene functionalization on moisture sensing performance by examining the water adsorption behavior of both pure and K+-functionalized MXene-based sensors. Two different concentrations of K+-functionalized MXene, 1M and 3M, were investigated. The results demonstrated that the 3M K+-functionalized MXene exhibited better performance. These sensors demonstrated high sensitivity of 1.580 ΔR/%Δ relative humidity (RH) across a wide humidity range (20%–80% RH) and featured ultrafast response and recovery times of 2.5 s and 12.5 s, respectively. Furthermore, the Mo2CT x -based sensors not only achieve the broadest operational range but also set a new benchmark for MXene-based moisture sensor sensitivity, outperforming the current state-of-the-art. These remarkable properties establish Mo2CT x -based sensors as highly promising candidates for printable, flexible, and non-invasive moisture detection systems, enabling real-time environmental and industrial monitoring.
- 1 September 2025
- Published by IOP Publishing in Flexible and Printed Electronics
- Vol. 10 (3) , 035018
Open AccessDirect functionalization of Mo2CT x MXene via single-step synthesis for printable, flexible, non-invasive moisture detection systems
A printable moisture sensor is an advanced device designed to measure water content in various materials, including soil, air, and other substances. The incorporation of K+ functionalization significantly increases the material’s hydrophilicity, promoting more effective adsorption and desorption of water molecules. This study explores the impact of MXene functionalization on moisture sensing performance by examining the water adsorption behavior of both pure and K+-functionalized MXene-based sensors. Two different concentrations of K+-functionalized MXene, 1M and 3M, were investigated. The results demonstrated that the 3M K+-functionalized MXene exhibited better performance. These sensors demonstrated high sensitivity of 1.580 ΔR/%Δ relative humidity (RH) across a wide humidity range (20%–80% RH) and featured ultrafast response and recovery times of 2.5 s and 12.5 s, respectively. Furthermore, the Mo2CT x -based sensors not only achieve the broadest operational range but also set a new benchmark for MXene-based moisture sensor sensitivity, outperforming the current state-of-the-art. These remarkable properties establish Mo2CT x -based sensors as highly promising candidates for printable, flexible, and non-invasive moisture detection systems, enabling real-time environmental and industrial monitoring.
- 4 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (8) , 11182-11196
A 30-mA Compensation-Free Output-Capacitorless Analog LDO With Hybrid Adaptive Biasing
This article presents an output-capacitorless low-dropout regulator (OCL-LDO), merging with a hybrid push–pull buffer. The hybrid push–pull buffer implements a dynamic and adaptive biasing push–pull gate driving circuit, achieving stability without needing a complex compensation circuit and external load capacitor. Our devised OCL-LDO can operate with a load current range of 0–30 mA, with a quiescent current of 7 μA at zero load current. The proposed OCL-LDO is fabricated in a 0.18-μm CMOS process with an active area of 0.03 mm2. Measurement results show that with a load current stepping from 0–30 mA and an edge time of 100 ns, the output voltage undershoot is 0.14 V, with a corresponding recovery time of 150 ns. The measured load regulation is 0.207 mV/mA at a supply voltage of 1.15 V and a dropout voltage of 0.15 V.
- 4 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (8) , 11182-11196
A 30-mA Compensation-Free Output-Capacitorless Analog LDO With Hybrid Adaptive Biasing
This article presents an output-capacitorless low-dropout regulator (OCL-LDO), merging with a hybrid push–pull buffer. The hybrid push–pull buffer implements a dynamic and adaptive biasing push–pull gate driving circuit, achieving stability without needing a complex compensation circuit and external load capacitor. Our devised OCL-LDO can operate with a load current range of 0–30 mA, with a quiescent current of 7 μA at zero load current. The proposed OCL-LDO is fabricated in a 0.18-μm CMOS process with an active area of 0.03 mm2. Measurement results show that with a load current stepping from 0–30 mA and an edge time of 100 ns, the output voltage undershoot is 0.14 V, with a corresponding recovery time of 150 ns. The measured load regulation is 0.207 mV/mA at a supply voltage of 1.15 V and a dropout voltage of 0.15 V.
- Open Access
- 10 March 2025
- Published by Univ. of Malaya in Journal of New Explorations in Electrical Engineering
- Vol. 1 (1) , 40-48
Investigation of Material and Geometric Effects on the Performance of Gate All Around Nanowire TFET and FET Devices
Advancements in nanoscale technology have enabled lower operating voltages and reduced power consumption, but also increased leakage currents. This study explores the performance of Tunnel Field-Effect Transistors (TFETs) and Field-Effect Transistors (FETs) using gate-all-around (GAA) silicon nanowires (Si-NW), which offer improvements over traditional MOSFETs by reducing short channel effects. The optimized GAA NWTFETs achieved a significant reduction in threshold voltage (69.5%) and leakage current (6.39%), while enhancing ON current, subthreshold swing, and ON/OFF current ratio. Similarly, the optimized GAA NWFETs demonstrated a substantial reduction in leakage current (97.59%) and a dramatic improvement in the ON/OFF current ratio by 4611.97%. These results highlight the potential of GAA nanowire TFETs and FETs in advancing semiconductor technologies with improved performance and energy efficiency.
- 10 March 2025
- Published by Univ. of Malaya in Journal of New Explorations in Electrical Engineering
- Vol. 1 (1) , 40-48
Open AccessInvestigation of Material and Geometric Effects on the Performance of Gate All Around Nanowire TFET and FET Devices
Advancements in nanoscale technology have enabled lower operating voltages and reduced power consumption, but also increased leakage currents. This study explores the performance of Tunnel Field-Effect Transistors (TFETs) and Field-Effect Transistors (FETs) using gate-all-around (GAA) silicon nanowires (Si-NW), which offer improvements over traditional MOSFETs by reducing short channel effects. The optimized GAA NWTFETs achieved a significant reduction in threshold voltage (69.5%) and leakage current (6.39%), while enhancing ON current, subthreshold swing, and ON/OFF current ratio. Similarly, the optimized GAA NWFETs demonstrated a substantial reduction in leakage current (97.59%) and a dramatic improvement in the ON/OFF current ratio by 4611.97%. These results highlight the potential of GAA nanowire TFETs and FETs in advancing semiconductor technologies with improved performance and energy efficiency.
- 3 March 2025
- Published by Wiley in Chemnanomat
- Vol. 11 (3)
Optimization of Etching Time, Temperature of Metal Salts in Surface‐texturized Silicon Fabricated Through One‐Step Metal‐Assisted Chemical Etching
This study delves into the Metal‐Assisted Chemical Etching (MACE) of p‐type monocrystalline silicon wafers, with a focus on tailoring surface morphology for heightened performance as thermal absorbers. Employing diverse metal catalysts—specifically, nickel nitrate hexahydrate and silver nitrate salts—the investigation systematically explores the impact of catalyst type, etching time and temperature on nanostructure formation. One of the objectives was to maintain the etching temperature to be as low as possible through the application of the metal catalysts. Achieving >2 of thermal energy absorbance in the UV‐Vis‐NIR range required immersing samples in a nickel nitrate salt solution at room temperature for 60 minutes. Characterization through UV‐Vis‐NIR spectroscopy revealed reflectance and absorbance spectra, with silver nitrate salt‐etched samples demonstrating exceptional performance, achieving the lowest reflectance values within the critical wavelength range of 300–1800 nm. Notably, after 60 minutes of etching, silver nitrate salt‐etched samples produced reflectance values ranging from 0.19 % to 3.45 %. Optimized parameters for nickel nitrate salt‐etched samples were identified at 30 minutes of etching and 50 °C, showcasing an average reflectance of 1.54 %. The consideration of energy conservation was paramount, prompting the initial observation of each catalyst's performance during the etching process with no heating at room temperature. Subsequently, in the extended phase of the study, the etching temperature was gradually increased. Raising the etching temperature served as a method of varying the process parameter to observe its impact on the formation of surface nanostructures and absorbing performance. The study concludes with recommendations for future research, advocating for the exploration of additional metal catalysts and investigation of combined catalysts.
- 3 March 2025
- Published by Wiley in Chemnanomat
- Vol. 11 (3)
Optimization of Etching Time, Temperature of Metal Salts in Surface‐texturized Silicon Fabricated Through One‐Step Metal‐Assisted Chemical Etching
This study delves into the Metal‐Assisted Chemical Etching (MACE) of p‐type monocrystalline silicon wafers, with a focus on tailoring surface morphology for heightened performance as thermal absorbers. Employing diverse metal catalysts—specifically, nickel nitrate hexahydrate and silver nitrate salts—the investigation systematically explores the impact of catalyst type, etching time and temperature on nanostructure formation. One of the objectives was to maintain the etching temperature to be as low as possible through the application of the metal catalysts. Achieving >2 of thermal energy absorbance in the UV‐Vis‐NIR range required immersing samples in a nickel nitrate salt solution at room temperature for 60 minutes. Characterization through UV‐Vis‐NIR spectroscopy revealed reflectance and absorbance spectra, with silver nitrate salt‐etched samples demonstrating exceptional performance, achieving the lowest reflectance values within the critical wavelength range of 300–1800 nm. Notably, after 60 minutes of etching, silver nitrate salt‐etched samples produced reflectance values ranging from 0.19 % to 3.45 %. Optimized parameters for nickel nitrate salt‐etched samples were identified at 30 minutes of etching and 50 °C, showcasing an average reflectance of 1.54 %. The consideration of energy conservation was paramount, prompting the initial observation of each catalyst's performance during the etching process with no heating at room temperature. Subsequently, in the extended phase of the study, the etching temperature was gradually increased. Raising the etching temperature served as a method of varying the process parameter to observe its impact on the formation of surface nanostructures and absorbing performance. The study concludes with recommendations for future research, advocating for the exploration of additional metal catalysts and investigation of combined catalysts.