Ali M. Zolali
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ali M. Zolali has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Basil D. Favis
CREPEC, Department of Chemical Engineering, École Polytechnique de Montréal, Montréal, Québec H3T 1J4, Canada
5 shared publications - Alan Taub
University of Michigan
3 shared publications - Jacob Harris
University of Michigan
3 shared publications - Luohaoran Wang
Department of Mechanical Engineering, University of Michigan, Ann Arbor, MI 48109, USA
3 shared publications - Mihaela Banu
Department of Mechanical Engineering, University of Michigan, Ann Arbor, MI 48109, USA
3 shared publications - Sangharsha Gharat
University of Michigan
3 shared publications
Latest Publications
- Open Access
- 14 April 2026
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 387, 61-73
Thermo-Chemical Modeling and Experimental Validation of Pultruded Glass Fiber Reinforced Composites
This work develops and validates thermo-chemical models for pultrusion of glass fiber–reinforced polyurethane composites on an industrial PulFlex production line. A reduced one-dimensional model combining a calibrated Kamal–Sourour (KS) cure law with an Arrhenius type chemo-rheological viscosity formulation is cross-validated against a three-dimensional ANSYS Composite Cure Simulation using identical material inputs along a three-zone, 0.9144 m heated die. Embedded thermocouples provide in-die temperature histories at 50.8 cm·min⁻¹ for calibration, while additional differential scanning calorimetry (DSC) measurements supply degree of cure (DoC) profiles for independent validation. At the industrial operating speed of 50.8 cm·min⁻¹, the mathematical and ANSYS models both reproduce the measured temperature peak location and exit temperature within a few degrees Celsius and predict a die-exit DoC of approximately 0.95, confirming near-complete curing. Using these calibrated fields as inputs to an analytical pulling-resistance formulation, both models predict comparable pulling force magnitudes and plateau behavior, demonstrating that the simplified 1D framework can capture not only thermo-chemical evolution but also process resistance trends over a range of pulling speeds. The validated 1D model therefore enables efficient exploration of speed–temperature–force tradeoffs for process window design, while the 3D ANSYS model provides a higher-fidelity reference for local gradients and future thermo–chemo–mechanical extensions.
- 14 April 2026
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 387, 61-73
Open AccessThermo-Chemical Modeling and Experimental Validation of Pultruded Glass Fiber Reinforced Composites
This work develops and validates thermo-chemical models for pultrusion of glass fiber–reinforced polyurethane composites on an industrial PulFlex production line. A reduced one-dimensional model combining a calibrated Kamal–Sourour (KS) cure law with an Arrhenius type chemo-rheological viscosity formulation is cross-validated against a three-dimensional ANSYS Composite Cure Simulation using identical material inputs along a three-zone, 0.9144 m heated die. Embedded thermocouples provide in-die temperature histories at 50.8 cm·min⁻¹ for calibration, while additional differential scanning calorimetry (DSC) measurements supply degree of cure (DoC) profiles for independent validation. At the industrial operating speed of 50.8 cm·min⁻¹, the mathematical and ANSYS models both reproduce the measured temperature peak location and exit temperature within a few degrees Celsius and predict a die-exit DoC of approximately 0.95, confirming near-complete curing. Using these calibrated fields as inputs to an analytical pulling-resistance formulation, both models predict comparable pulling force magnitudes and plateau behavior, demonstrating that the simplified 1D framework can capture not only thermo-chemical evolution but also process resistance trends over a range of pulling speeds. The validated 1D model therefore enables efficient exploration of speed–temperature–force tradeoffs for process window design, while the 3D ANSYS model provides a higher-fidelity reference for local gradients and future thermo–chemo–mechanical extensions.
- Open Access
A Theory-Guided Machine Learning and Molecular Dynamics Approach for Characterizing Fast-Curing Polyurethane Systems
Fast-curing polyurethane (PU) systems are attractive for high-throughput manufacturing, but quantifying cure kinetics, gelation, and cure-dependent glass transition temperature () is difficult, especially at a low degree of cure (DoC). Here, a fast-reacting BASF PU formulation was studied using non-isothermal differential scanning calorimetry (DSC) at multiple heating rates, rheometry at 50 °C, and molecular dynamics (MD) simulations to extend in the low-DoC regime. DSC provided reaction enthalpy and conversion histories, and Kamal–Sourour (KS) parameters were identified by robust nonlinear fitting, reproducing conversion and curing rate profiles (R2 > 0.99 and >0.95). Rheology indicated gelation between 475 and 625 s (DoC ≈ 0.53), and DSC-based at uncured, gelation, and fully cured states, established the experimental trend. MD (LAMMPS) with topological crosslinking and NPT thermal scans extracted from density–temperature slopes at selected DoC points. Experimental and MD data were fused with Gaussian process regression constrained by the DiBenedetto relationship (5-fold cross-validation), giving λ ≈ 0.29 and confidence intervals. This framework links kinetics, gelation, and evolution for fast-curing PU and identifies the low-DoC region as the main source of uncertainty.Open AccessA Theory-Guided Machine Learning and Molecular Dynamics Approach for Characterizing Fast-Curing Polyurethane Systems
Fast-curing polyurethane (PU) systems are attractive for high-throughput manufacturing, but quantifying cure kinetics, gelation, and cure-dependent glass transition temperature () is difficult, especially at a low degree of cure (DoC). Here, a fast-reacting BASF PU formulation was studied using non-isothermal differential scanning calorimetry (DSC) at multiple heating rates, rheometry at 50 °C, and molecular dynamics (MD) simulations to extend in the low-DoC regime. DSC provided reaction enthalpy and conversion histories, and Kamal–Sourour (KS) parameters were identified by robust nonlinear fitting, reproducing conversion and curing rate profiles (R2 > 0.99 and >0.95). Rheology indicated gelation between 475 and 625 s (DoC ≈ 0.53), and DSC-based at uncured, gelation, and fully cured states, established the experimental trend. MD (LAMMPS) with topological crosslinking and NPT thermal scans extracted from density–temperature slopes at selected DoC points. Experimental and MD data were fused with Gaussian process regression constrained by the DiBenedetto relationship (5-fold cross-validation), giving λ ≈ 0.29 and confidence intervals. This framework links kinetics, gelation, and evolution for fast-curing PU and identifies the low-DoC region as the main source of uncertainty. - Open Access
- 2 February 2026
- Published by MDPI AG in Preprints.org
A Theory-Guided Machine Learning and Molecular Dynamics Approach for Characterizing Fast-Curing Polyurethane Systems
Fast-curing polyurethane (PU) systems are attractive for high throughput manufacturing, but quantifying cure kinetics, gelation, and cure-dependent glass transition temperature (Tg) is difficult, especially at low degree of cure (DoC). Here, a fast-reacting BASF PU formulation was studied using non-isothermal differential scanning calorimetry (DSC) at multiple heating rates, rheometry at 50 °C, and molecular dynamics (MD) simulations to extend Tg(α) in the low-DoC regime. DSC provided reaction enthalpy and conversion histories, and Kamal–Sourour (KS) parameters were identified by robust nonlinear fitting, reproducing conversion and curing-rate profiles (R² > 0.99 and > 0.95). Rheology indicated gelation at ~550–600 s (DoC ≈ 0.53), and DSC-based Tg at uncured, gelation, and fully cured states established the experimental Tg trend. MD (LAMMPS) with topological crosslinking and NPT thermal scans extracted Tg from density–temperature slopes at selected DoC points. Experimental and MD Tg data were fused with Gaussian process regression constrained by the DiBenedetto relationship (5-fold cross-validation), giving λ ≈ 0.28 and confidence intervals. This framework links kinetics, gelation, and Tg evolution for fast-curing PU and identifies the low-DoC region as the main source of uncertainty.
- 2 February 2026
- Published by MDPI AG in Preprints.org
Open AccessA Theory-Guided Machine Learning and Molecular Dynamics Approach for Characterizing Fast-Curing Polyurethane Systems
Fast-curing polyurethane (PU) systems are attractive for high throughput manufacturing, but quantifying cure kinetics, gelation, and cure-dependent glass transition temperature (Tg) is difficult, especially at low degree of cure (DoC). Here, a fast-reacting BASF PU formulation was studied using non-isothermal differential scanning calorimetry (DSC) at multiple heating rates, rheometry at 50 °C, and molecular dynamics (MD) simulations to extend Tg(α) in the low-DoC regime. DSC provided reaction enthalpy and conversion histories, and Kamal–Sourour (KS) parameters were identified by robust nonlinear fitting, reproducing conversion and curing-rate profiles (R² > 0.99 and > 0.95). Rheology indicated gelation at ~550–600 s (DoC ≈ 0.53), and DSC-based Tg at uncured, gelation, and fully cured states established the experimental Tg trend. MD (LAMMPS) with topological crosslinking and NPT thermal scans extracted Tg from density–temperature slopes at selected DoC points. Experimental and MD Tg data were fused with Gaussian process regression constrained by the DiBenedetto relationship (5-fold cross-validation), giving λ ≈ 0.28 and confidence intervals. This framework links kinetics, gelation, and Tg evolution for fast-curing PU and identifies the low-DoC region as the main source of uncertainty.
- 11 February 2020
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 53 (4) , 1346-1355
Nanoconfinement Induced Direct Formation of Form I and III Crystals inside in Situ Formed Poly(butene-1) Nanofibrils
- 11 February 2020
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 53 (4) , 1346-1355
Nanoconfinement Induced Direct Formation of Form I and III Crystals inside in Situ Formed Poly(butene-1) Nanofibrils
- 1 July 2019
- Published by Elsevier in Journal of Colloid and Interface Science
- Vol. 548, 206-216
Robust, ultra-insulative and transparent polyethylene-based hybrid silica aerogel with a novel non-particulate structure
- 1 July 2019
- Published by Elsevier in Journal of Colloid and Interface Science
- Vol. 548, 206-216
Robust, ultra-insulative and transparent polyethylene-based hybrid silica aerogel with a novel non-particulate structure
- 2 May 2018
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 51 (10) , 3572-3581
Toughening of Cocontinuous Polylactide/Polyethylene Blends via an Interfacially Percolated Intermediate Phase
- 2 May 2018
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 51 (10) , 3572-3581
Toughening of Cocontinuous Polylactide/Polyethylene Blends via an Interfacially Percolated Intermediate Phase
- 21 March 2017
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 13 (15) , 2844-2856
Partial to complete wetting transitions in immiscible ternary blends with PLA: the influence of interfacial confinement
In this study it is shown that the three different intermediate phases in melt blended ternary PLA/PHBV/PBS, PLA/PBAT/PE and PLA/PE/PBAT systems all demonstrate partial wetting, but have very different wetting behaviors as a function of composition and annealing. The interfacial tension of the various components, their spreading coefficients and the contact angles of the confined partially wet droplets at the interface are examined in detail. A wetting transition from partially wet droplets to a complete layer at the interface is observed for both PHBV and PBAT by increasing the concentration and also by annealing. In contrast, in PLA/PE/PBAT, the partially wet droplets of PE at the interface of PLA/PBAT coalesce and grow in size, but remain partially wet even at a high PE concentration of 20% and after 30 min of quiescent annealing. The dewetting speed of the intermediate phase is found to be the principal factor controlling these wetting transitions. This work shows the significant potential for controlled wetting and structuring in ternary polymer systems.
- 21 March 2017
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 13 (15) , 2844-2856
Partial to complete wetting transitions in immiscible ternary blends with PLA: the influence of interfacial confinement
In this study it is shown that the three different intermediate phases in melt blended ternary PLA/PHBV/PBS, PLA/PBAT/PE and PLA/PE/PBAT systems all demonstrate partial wetting, but have very different wetting behaviors as a function of composition and annealing. The interfacial tension of the various components, their spreading coefficients and the contact angles of the confined partially wet droplets at the interface are examined in detail. A wetting transition from partially wet droplets to a complete layer at the interface is observed for both PHBV and PBAT by increasing the concentration and also by annealing. In contrast, in PLA/PE/PBAT, the partially wet droplets of PE at the interface of PLA/PBAT coalesce and grow in size, but remain partially wet even at a high PE concentration of 20% and after 30 min of quiescent annealing. The dewetting speed of the intermediate phase is found to be the principal factor controlling these wetting transitions. This work shows the significant potential for controlled wetting and structuring in ternary polymer systems.