ZLZhen Li

Zhen Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Zhen Li has a total of 16 co-authors. Here are the top co-authors by number of shared publications:

  • Xiaokang Yin

    School of Mechanical and Electrical Engineering, China University of Petroleum (East China), Qingdao, China

    4 shared publications
  • Wei Li

    School of Mechanical and Electrical Engineering, China University of Petroleum (East China), Qingdao, China

    3 shared publications
  • Chen Li

    Centre for Offshore Engineering and Safety Technology, China University of Petroleum (East China), Qingdao 266580, China

    1 shared publication
  • Gaofeng Ma

    National Engineering Research Center of Marine Geophysical Prospecting and Exploration and Development Equipment, China University of Petroleum (East), Qingdao 266580, China

    1 shared publication
  • Guoming Chen

    Center for Offshore Engineering and Safety Technology, China University of Petroleum (East China), Qingdao 266580, China

    1 shared publication
  • Guoming Chen

    Centre for Offshore Engineering and Safety Technology, China University of Petroleum (East China), Qingdao 266580, China

    1 shared publication

Latest Publications

  • A Novel Shear Horizontal Guided Wave EMAT With Periodic Solenoid Coils and a Single Magnet

    by Hongyuan Zhang, Xiaokang Yin, Gaofeng Ma, Zhenshun Wei, Ziheng Zhang, Jianxi Ding, Zhen Li, Xin’aN Yuan, Wei Li

    Periodic Permanent Magnets Electromagnetic Acoustic Transducers (PPM EMATs) are commonly employed to generate Shear Horizontal (SH) guided waves for defect scanning in steel structures. During scanning, electromagnets can be used as alternatives to permanent magnets to generate static bias magnetic fields, thereby addressing the problem of permanent magnets attracting iron filings on the surface of steel structures. However, since the PPM EMATs have multiple magnet units and complex magnetic field distributions, replacing permanent magnets with electromagnets presents significant challenges. In this paper, a novel SH guided waves EMAT with Periodic Solenoid Coils (PSC) and a single magnet (referred to as the PSC EMAT) was developed. The design methodology for the PSC EMATs was presented, using the excitation of the single SH0 mode guided waves in a steel plate as a case study. The transduction process and excitation performance of the PSC EMATs were analyzed through both Finite Element (FE) simulations and experimental investigations. The results from both simulations and experiments demonstrate that the PSC EMAT can effectively generate single SH0 mode guided waves that propagate in four directions, with the forward directions identified as the primary orientations for defect inspection. These findings indicate that PSC EMATs can reliably generate and receive SH guided waves using a simplified static bias magnetic field, providing a foundation for the future application of electromagnets.


  • Open Access

    Corrosion Depth Inversion Method Based on the Lift-Off Effect of the Capacitive Imaging (CI) Technique

    by Xiaokang Yin, Zhen Li, Xian’an Yuan, Wei Li, Guoming Chen

    As a new Non-destructive Evaluation (NDE) technique, capacitive imaging (CI) has been used to detect defects in oil pipelines, composite sucker rods and storage tanks in recent years. When a CI sensor is used to detect corrosion defect on a conducting surface with or without an insulation layer, the depth information of corrosion defect is difficult to acquire due to the non-linearity of the probing field. This paper proposed a corrosion depth inversion method based on the lift-off effect of the CI technique. The proposed depth inversion method, which includes three steps, namely establishing the lift-off curve, obtaining the scan curve and fitting inversion, are introduced and evaluated. In the FE simulations, the error rates of the inversion depths are less than 1.20%. CI experiments were carried out to acquire the depth information of a step shape specimen using the CI experimental system and the proposed corrosion depth inversion method. The results show that the depth inversion method can meet the need of obtaining the actual depth information with the error rates of the inversion depths being less than 10.00%. A CI experiment on a machined and corroded specimen was carried out to further demonstrate the feasibility of the proposed inversion method for corrosion defects with different depths. Both results from FE models and experiments indicate that the proposed method is promising to achieve the quantitative NDE of the Corrosion Under Insulation (CUI).


  • Open Access

    Lift-off Effect for Capacitive Imaging Sensors

    by Xiaokang Yin, Chen Li, Zhen Li, Wei Li, Guoming Chen

    Capacitive Imaging (CI) sensors are capable of non-destructively detecting both surface and hidden defects in dielectric materials and characterizing conducting surfaces through a relatively thick insulation layer. However, the complex Measurement Sensitivity Distribution (MSD) of CI sensors render the sensor capacitance variation with lift-off highly non-linear, which may lead to misinterpretation of defect indications. This work systematically studied the lift-off effect using both Finite Element (FE) analysis and experimental approaches. Sensor MSD was used as a tool to predict the imaging performance. Normalized Variation Ratio (NVR) was introduced and used to characterise sensor responses due to defects for a CI sensor. Both the FE analysis and experiments suggest that the lift-off effect for a CI sensor is specimen type and condition dependent. For a given defect, the NVR may vary non-monotonically with increased lift-offs. A case study on a glass-fibre composite/aluminium hybrid structure with multiple artificial defects demonstrated the feasibility of defects discrimination using multiple CI scans with increased lift-offs.


  • Open Access

    Further Investigations into the Capacitive Imaging Technique Using a Multi-Electrode Sensor

    by Zhen Li, Guoming Chen, Yue Gu, Kefan Wang, Wei Li, Xiaokang Yin

    As a novel non-destructive testing technique, capacitive imaging (CI) has been used to detect defects within the insulation layer and metal surface of an insulated metallic structure, that is, pipe or vessel. Due to the non-linearity of the probing field, the defects at different depths in the insulation layer are difficult to compare accurately using the conventional CI sensor with a single pair of electrodes. In addition, the conventional CI sensor cannot provide adequate information to discriminate the defects in the insulation layer and metal surface. In order to solve the above-mentioned problems, the multi-electrode sensor is introduced. The multi-electrode sensor uses multiple quasi-static fringing electric fields generated by an array of coplanar electrodes to obtain extra information about the defects in the specimen. In this work, the feasibility of multiple quasi-static electric fields detecting the defects was demonstrated and the Measurement Sensitivity Distributions (MSDs) of the multi-electrode sensor detecting the defects were acquired using the FEM models. The simulation and experimental results show that the Dynamic Change Rates (DCRs) of the measured values obtained at the center of the defects in the insulator layer and metal surface present different variation patterns, which can be used to discriminate these two different kinds of defects. The reasons for the different variation patterns of DCRs were explained by the changing trends of MSDs with increased electrode separation. In addition, it was demonstrated that the different depths of the defects in the insulator layer can be compared accurately by comprehensive analysis of the detection results from all the electrode pairs.