Tai Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tai Wang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Sansan Ao
School of Materials Science and Engineering, Tianjin University, Tianjin 300354, China
2 shared publications - Yangchuan Cai
School of Materials Science and Engineering, Tianjin University of Technology, Tianjin 300384, China
2 shared publications - Zhen Luo
School of Materials Science and Engineering, Tianjin University, Tianjin 300350, China
2 shared publications - Sunusi Marwana Manladan
Department of Mechanical Engineering, Faculty of Engineering, Bayero University, Kano, Kano, Nigeria
1 shared publication - Yizhe Huang
Department of Computer Science and Engineering, University of California-San Diego, La Jolla, CA 92122, USA
1 shared publication - Yu Dai
School of Education, Tianjin University, Tianjin, P.R. China
1 shared publication
Latest Publications
- Open Access
Microstructure and Properties of Surface-Modified Plates and Their Welded Joints
The surface of Q235 low carbon steel was modified by the metal inert-gas welding (MIG) method; a 304 stainless steel surfacing layer was fabricated to improve the properties of Q235 low carbon steel. For practical industry application, keyhole tungsten inter gas (K-TIG) welding was used to weld the surface-modified plates. The microstructure, elemental distribution, micro-hardness, and corrosion resistance of the surface-modified plates and the welded joints were analyzed. The corrosion tests of welded joints and surface-modified plates were carried out with the electrochemical method and hydrochloric acid immersion method, respectively, and surface morphology after corrosion was studied. The results show that the surface-modified plates and their welded joints were defect-free. The microstructure of the surfacing layer consisted of austenite, martensite, and ferrite; and the microstructure of the weld consisted mainly of martensite. The hardness and corrosion resistance of the surfacing layer was superior to that that of low carbon steel. The micro-hardness of the weld is higher than that of the stainless steel surfacing layer and the base material. The corrosion resistance of the surfacing layer is the best, and the corrosion resistance of the welding seam is better than that of the base material.
Open AccessMicrostructure and Properties of Surface-Modified Plates and Their Welded Joints
The surface of Q235 low carbon steel was modified by the metal inert-gas welding (MIG) method; a 304 stainless steel surfacing layer was fabricated to improve the properties of Q235 low carbon steel. For practical industry application, keyhole tungsten inter gas (K-TIG) welding was used to weld the surface-modified plates. The microstructure, elemental distribution, micro-hardness, and corrosion resistance of the surface-modified plates and the welded joints were analyzed. The corrosion tests of welded joints and surface-modified plates were carried out with the electrochemical method and hydrochloric acid immersion method, respectively, and surface morphology after corrosion was studied. The results show that the surface-modified plates and their welded joints were defect-free. The microstructure of the surfacing layer consisted of austenite, martensite, and ferrite; and the microstructure of the weld consisted mainly of martensite. The hardness and corrosion resistance of the surfacing layer was superior to that that of low carbon steel. The micro-hardness of the weld is higher than that of the stainless steel surfacing layer and the base material. The corrosion resistance of the surfacing layer is the best, and the corrosion resistance of the welding seam is better than that of the base material.
- Open Access
The Wear Properties of TiC/Al-Based Composite Coating Applied by Laser Cladding
Aluminum powders with different concentrations of TiC ceramic particles were applied to an AZ31B magnesium alloy by laser cladding. Due to differences in coefficients of thermal expansion, the distribution of TiC ceramic particles in the cladding layer was not uniform. The results show that the degree of TiC ceramic particle agglomeration in the cladding layer increases with increasing TiC content. The phases of cladding metal mainly consisted of Al, γ-Al12Mg17, β-Al3Mg2, and TiC. The γ-Al12Mg17 phase mainly distributed to the bottom of the cladding layer, and the β-Al3Mg2 phase distributed to the middle and surface areas. The existence of the γ-Al12Mg17 phase enhanced the hardness of the fusion zone. The microhardness of the cladding layer increased with increasing TiC ceramic particle content. An appropriate TiC content improved the wear resistance of the cladding layer. When the TiC content was excessive, the agglomeration behavior of TiC ceramic particles strongly affected the wear resistance of the coatings.
Open AccessThe Wear Properties of TiC/Al-Based Composite Coating Applied by Laser Cladding
Aluminum powders with different concentrations of TiC ceramic particles were applied to an AZ31B magnesium alloy by laser cladding. Due to differences in coefficients of thermal expansion, the distribution of TiC ceramic particles in the cladding layer was not uniform. The results show that the degree of TiC ceramic particle agglomeration in the cladding layer increases with increasing TiC content. The phases of cladding metal mainly consisted of Al, γ-Al12Mg17, β-Al3Mg2, and TiC. The γ-Al12Mg17 phase mainly distributed to the bottom of the cladding layer, and the β-Al3Mg2 phase distributed to the middle and surface areas. The existence of the γ-Al12Mg17 phase enhanced the hardness of the fusion zone. The microhardness of the cladding layer increased with increasing TiC ceramic particle content. An appropriate TiC content improved the wear resistance of the cladding layer. When the TiC content was excessive, the agglomeration behavior of TiC ceramic particles strongly affected the wear resistance of the coatings.