Boris S. Ermakov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Boris S. Ermakov has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
- Oleg V. Shvetsov
Peter the Great St. Petersburg Polytechnic University, St. Petersburg, Russian Federation
6 shared publications - S. A. Vologzhanina
Empress Catherine II St Petersburg Min Univ, St Petersburg, Russia
3 shared publications - A. A. Lapechenkov
Peter the Great St. Petersburg Polytechnic University, St. Petersburg, Russia
2 shared publications - E. L. Gyulikhandanov
Peter the Great St. Petersburg Polytechnic University, St. Petersburg, Russia
2 shared publications - Ekaterina Alekseeva
Scientific and Technological Complex “New Technologies and Materials”, Institute of Advanced Engineering Technologies, Peter the Great Saint-Petersburg Polytechnic University, Polytechnicheskaya 29, 194064 St. Petersburg, Russia
2 shared publications - L. Galata
Peter the Great St. Petersburg Polytechnic University, St. Petersburg, Russia
2 shared publications
Latest Publications
- Open Access
- 30 October 2026
- Published by Industrial University of Tyumen in Oil and Gas Studies
- No. 5,p. 177-191
Recycling composite piles from oil and gas infrastructure into secondary feedstock for additive manufacturing
The expanding use of polymer composites in infrastructure calls for recycling routes after the end of service. This study evaluates mechanically ground material from a hybrid basalt/glass-fibre composite pile as a filler for acrylonitrile butadiene styrene (ABS) filament and three-dimensional printing. Formulations containing 0, 10, 20 and 30 wt.% recyclate of a 0.10–0.20 mm sieve fraction were used to print two tensile and three three-point-bending specimens per formulation. The printing nozzle temperature was 260 °C. Mean maximum tensile stress decreased from 44.21 MPa for unfilled ABS to 35.49, 32.35 and 20.00 MPa, while flexural stress decreased from 79.58 to 70.46, 58.88 and 43.80 MPa, respectively. Flexural modulus remained within 2.60–2.77 GPa. At 30 wt.%, filament brittleness, winding difficulties and intermittent extrusion-nozzle clogging limited continuous filament length to 10 m. Formulations containing 10–20 wt.% recyclate warrant further development for auxiliary products whose intended use permits reduced mechanical performance. The results support further optimization of particle classification and processing conditions but do not establish a universally optimal formulation.
- 30 October 2026
- Published by Industrial University of Tyumen in Oil and Gas Studies
- No. 5,p. 177-191
Open AccessRecycling composite piles from oil and gas infrastructure into secondary feedstock for additive manufacturing
The expanding use of polymer composites in infrastructure calls for recycling routes after the end of service. This study evaluates mechanically ground material from a hybrid basalt/glass-fibre composite pile as a filler for acrylonitrile butadiene styrene (ABS) filament and three-dimensional printing. Formulations containing 0, 10, 20 and 30 wt.% recyclate of a 0.10–0.20 mm sieve fraction were used to print two tensile and three three-point-bending specimens per formulation. The printing nozzle temperature was 260 °C. Mean maximum tensile stress decreased from 44.21 MPa for unfilled ABS to 35.49, 32.35 and 20.00 MPa, while flexural stress decreased from 79.58 to 70.46, 58.88 and 43.80 MPa, respectively. Flexural modulus remained within 2.60–2.77 GPa. At 30 wt.%, filament brittleness, winding difficulties and intermittent extrusion-nozzle clogging limited continuous filament length to 10 m. Formulations containing 10–20 wt.% recyclate warrant further development for auxiliary products whose intended use permits reduced mechanical performance. The results support further optimization of particle classification and processing conditions but do not establish a universally optimal formulation.
- 23 April 2026
- Published by Springer Nature in Metallurgist
- Vol. 69 (10) , 1640-1647
Causes of gear tooth flank failure in a quarry excavator drive system
- 23 April 2026
- Published by Springer Nature in Metallurgist
- Vol. 69 (10) , 1640-1647
Causes of gear tooth flank failure in a quarry excavator drive system
- 1 April 2026
- Published by Springer Nature in Metallurgist
- Vol. 69 (12) , 1887-1894
Development of technological solutions for producing longitudinal-seam electric-welded pile pipes without bulk heat treatment
- 1 April 2026
- Published by Springer Nature in Metallurgist
- Vol. 69 (12) , 1887-1894
Development of technological solutions for producing longitudinal-seam electric-welded pile pipes without bulk heat treatment
- 1 April 2026
- Published by Springer Nature in Metallurgist
- Vol. 69 (12) , 1837-1845
Potential applications of bimetallic pipelines for offshore fields in the Arctic
- 1 April 2026
- Published by Springer Nature in Metallurgist
- Vol. 69 (12) , 1837-1845
Potential applications of bimetallic pipelines for offshore fields in the Arctic
- 26 October 2025
- Published by Metallurgizdat in Metallurg
- No. 10-2025,p. 129-134
ОЦЕНКА ПРИЧИН РАЗРУШЕНИЯ РАБОЧИХ ПОВЕРХНОСТЕЙ ЗУБЧАТЫХ КОЛЕС ПРИВОДА КАРЬЕРНОГО ЭКСКАВАТОРА
Развитие нефтегазового комплекса и предприятий добычи твердых полезных ископаемых, в настоящее время, сосредоточено в северных, наиболее удаленных регионах регионах страны. Известно, что сроки службы ряда узлов и деталей экскаваторов, бульдозеров и погрузчиков в условиях Арктического и Субарктического регионов РФ снижается в несколько раз. Анализ состояния поврежденных зубчатых колес, демонтированных с горнодобывающей техники, эксплуатируемой в условиях северных широт показал, что ускоренному выходу из строя зубчатых пар могут способствовать различные внешние воздействия и несоответствия качества продукции. Исследовали влияние химического состава материалов зубьев и зернограничных сегрегаций примесных атомов на сопротивляемость разрушению металла зубьев и развитию контактных повреждений в ходе длительной низкотемпературной эксплуатации. Проведенные исследования показали, что для описания процесса зарождения и развития закалочных трещин замедленного разрушения в поверхностных слоях зубьев ведомых колес тяговых зубчатых передач могут быть рекомендованы испытания на определение длительной трещиностойкости К1rth, при которых развитие трещины происходит по границам наследственных аустенитных зерен. The development of the oil and gas industry and solid mineral extraction enterprises is currently concentrated in the northern, most remote regions of the country. It is known that the service life of certain components and parts of excavators, bulldozers, and loaders is reduced severalfold in the Arctic and Subarctic conditions of the Russian Federation. An analysis of the condition of damaged gears removed from mining equipment operating in northern latitudes revealed that various external factors and product quality inconsistencies can contribute to accelerated gear failure. The purpose of this study is to identify the influence of the chemical composition of gear teeth and grain boundary segregation of impurity atoms on the resistance of gear teeth to metal fracture and the development of contact damage during long–term low–temperature operation. The conducted studies have shown that, to describe the process of initiation and development of hardening cracks of delayed destruction in the surface layers of the teeth of driven wheels of traction gear transmissions, tests to determine the long–term crack resistance K1rth can be recommended, in which crack development occurs along the boundaries of hereditary austenite grains.
- 26 October 2025
- Published by Metallurgizdat in Metallurg
- No. 10-2025,p. 129-134
ОЦЕНКА ПРИЧИН РАЗРУШЕНИЯ РАБОЧИХ ПОВЕРХНОСТЕЙ ЗУБЧАТЫХ КОЛЕС ПРИВОДА КАРЬЕРНОГО ЭКСКАВАТОРА
Развитие нефтегазового комплекса и предприятий добычи твердых полезных ископаемых, в настоящее время, сосредоточено в северных, наиболее удаленных регионах регионах страны. Известно, что сроки службы ряда узлов и деталей экскаваторов, бульдозеров и погрузчиков в условиях Арктического и Субарктического регионов РФ снижается в несколько раз. Анализ состояния поврежденных зубчатых колес, демонтированных с горнодобывающей техники, эксплуатируемой в условиях северных широт показал, что ускоренному выходу из строя зубчатых пар могут способствовать различные внешние воздействия и несоответствия качества продукции. Исследовали влияние химического состава материалов зубьев и зернограничных сегрегаций примесных атомов на сопротивляемость разрушению металла зубьев и развитию контактных повреждений в ходе длительной низкотемпературной эксплуатации. Проведенные исследования показали, что для описания процесса зарождения и развития закалочных трещин замедленного разрушения в поверхностных слоях зубьев ведомых колес тяговых зубчатых передач могут быть рекомендованы испытания на определение длительной трещиностойкости К1rth, при которых развитие трещины происходит по границам наследственных аустенитных зерен. The development of the oil and gas industry and solid mineral extraction enterprises is currently concentrated in the northern, most remote regions of the country. It is known that the service life of certain components and parts of excavators, bulldozers, and loaders is reduced severalfold in the Arctic and Subarctic conditions of the Russian Federation. An analysis of the condition of damaged gears removed from mining equipment operating in northern latitudes revealed that various external factors and product quality inconsistencies can contribute to accelerated gear failure. The purpose of this study is to identify the influence of the chemical composition of gear teeth and grain boundary segregation of impurity atoms on the resistance of gear teeth to metal fracture and the development of contact damage during long–term low–temperature operation. The conducted studies have shown that, to describe the process of initiation and development of hardening cracks of delayed destruction in the surface layers of the teeth of driven wheels of traction gear transmissions, tests to determine the long–term crack resistance K1rth can be recommended, in which crack development occurs along the boundaries of hereditary austenite grains.
- 1 March 2025
- Published by Springer Nature in Metallurgist
- Vol. 68 (11) , 1667-1675
The influence of welded joint microstructure on the corrosive properties of X70 steel
- 1 March 2025
- Published by Springer Nature in Metallurgist
- Vol. 68 (11) , 1667-1675
The influence of welded joint microstructure on the corrosive properties of X70 steel
- 7 November 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (7) , 961-969
Influence of drill pipe manufacturing technology on fracture mechanisms and fatigue properties
- 7 November 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (7) , 961-969
Influence of drill pipe manufacturing technology on fracture mechanisms and fatigue properties
- 5 September 2024
- Published by Industrial University of Tyumen in Oil and Gas Studies
- No. 4,p. 96-118
Analysis of reliability and efficiency of drill dipping piles for oil field construction in permafrost zone
Relocation of the main capacities of oil production infrastructure from Central to Northern Russia necessitated a re-evaluation of oilfield development strategies, particularly addressing the challenges of constructing foundations for pipelines, processing facilities, and power plants. These foundations are formed by drill-dipping piles into pre-drilled boreholes. The use of drill dipping piles in permafrost is technologically essential as alternative pile types are impractical. The most common are drill dipping piles fabricated from longitudinal seam pipes welded with high frequency current techniques (as per GOST 20295 and GOST R 58064). Performance of such pipes in permafrost conditions was evaluated through laboratory simulations mimicking operational conditions, as well as in-situ at the test site of Federal Research Centre "The Yakut Scientific Centre of the Siberian Branch of the Russian Academy of Sciences" where full-size piles were installed in firm loamy and wet peaty permafrost soils. Pipes both with and without post-weld heat treatment, as specified in SP 16.13330.2017, were tested. The authors examined static mechanical properties and impact toughness of the base metal and welded joints of the pipes, as well as corrosion resistance and crack resistance. The research revealed that post-weld heat treatment did not significantly enhance the reliability of drill dipping piles fabricated from 09G2S steel. Concurrently, microstructure analysis of the welded joints revealed a considerable number of defects along the weld-fusion line, potentially accelerating pile failure.
- 5 September 2024
- Published by Industrial University of Tyumen in Oil and Gas Studies
- No. 4,p. 96-118
Analysis of reliability and efficiency of drill dipping piles for oil field construction in permafrost zone
Relocation of the main capacities of oil production infrastructure from Central to Northern Russia necessitated a re-evaluation of oilfield development strategies, particularly addressing the challenges of constructing foundations for pipelines, processing facilities, and power plants. These foundations are formed by drill-dipping piles into pre-drilled boreholes. The use of drill dipping piles in permafrost is technologically essential as alternative pile types are impractical. The most common are drill dipping piles fabricated from longitudinal seam pipes welded with high frequency current techniques (as per GOST 20295 and GOST R 58064). Performance of such pipes in permafrost conditions was evaluated through laboratory simulations mimicking operational conditions, as well as in-situ at the test site of Federal Research Centre "The Yakut Scientific Centre of the Siberian Branch of the Russian Academy of Sciences" where full-size piles were installed in firm loamy and wet peaty permafrost soils. Pipes both with and without post-weld heat treatment, as specified in SP 16.13330.2017, were tested. The authors examined static mechanical properties and impact toughness of the base metal and welded joints of the pipes, as well as corrosion resistance and crack resistance. The research revealed that post-weld heat treatment did not significantly enhance the reliability of drill dipping piles fabricated from 09G2S steel. Concurrently, microstructure analysis of the welded joints revealed a considerable number of defects along the weld-fusion line, potentially accelerating pile failure.
- 1 September 2023
- Published by Springer Nature in Metallurgist
- Vol. 67 (5-6) , 644-651
Investigation of Material Properties for Cryogenic Products, Produced by Additive Manufacturing Techniques
- 1 September 2023
- Published by Springer Nature in Metallurgist
- Vol. 67 (5-6) , 644-651
Investigation of Material Properties for Cryogenic Products, Produced by Additive Manufacturing Techniques