EAEvgenii Aryshenskii

Evgenii Aryshenskii

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Evgenii Aryshenskii has a total of 31 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Development of an Earing Model with Consideration for the Crystallographic Texture of Sheet Metal During Axisymmetric Drawing

    by Ya. A. Erisov, F. V. Grechnikov, S. V. Suridin, V. A. Razzhivin, E. V. Aryshenskii, S. V. Konovalov

    A calculation model is developed for earing during cylindrical drawing of metallic materials, which is based on the phenomenological criterion of plasticity taking into account the crystallographic texture of the material. The model was verified by comparing the calculated earing defects with those observed in drawing tests on an aluminum preform. Further modeling shows that deformation orientations ({112}, {110}, {123}, and {100}) lead to earing at an angle of 45° to the rolling direction, while recrystallization orientations ({100} and {110}) lead to earing in the rolling and transverse directions. Crystallographic orientation {110} gives maximum earing, while orientation {123} causes minimum one. In all the cases, the contribution of plastic anisotropy and yield stress anisotropy to earing is almost the same, with a slight predominance of the latter. The earing behavior is shown by the example of materials with a two-component ({112} + {100}<001) texture: as the fraction of the {112} orientation grows, ears in the rolling and transverse directions are reduced, while they form at an angle of 45° to the rolling direction. Considering such influence, the earing coefficient is minimum at 55–60% of the {112} component.


  • Developing a new method for calculating the nuclei of orientations during aluminum alloys recrystallization

    by Е. V. Aryshensky, S. V. Konovalov, E. D. Beglov, V. Yu. Aryshensky

    A new approach to modeling texture formation in aluminum alloys du ring their recrystallization is proposed. It is based on a previously developed method for calculating texture formation during deformation, which involves solving the problem of deformation of a solid at the macro level by the finite element method. In each layer with a homogeneous stress-strain state, a domain is defined, which is divided into finite elements. Each element corresponds to a crystallite having a specific crystallographic orientation. Next the domain deformation problem is solved based on the boundary conditions obtained from the solution at the macro level. A new approach to the nuclei calculation during recrystallization involves the use of finite elements with a high approximation order or the division of one crystallite into several finite elements. This approach makes it possible to find areas with deformation heterogeneity and thereby more accurately determine the number and type of nuclei of the recrystallized structure. The model is able to predict the number of nuclei formed at the boundaries of new grains, shear and cubic bands, as well as in areas with crystal lattice distortions due to the presence of intermetallides in the structure. To verify the performance of the model, we solved the problem of texture formation during self-annealing in a roll of AA8011 alloy after its hot rolling in a continuous train. Alloy AA8011 refers to deformable alloys of the Al – Fe system, which are likely to forming a sharp cube texture, therefore, the correct calculation of the nuclei of this orientation for alloy AA8011 is relevant. The results showed that, without taking into account the inhomogeneity of the deformation, the model predicts a smaller number of cubic textures and a larger number of β-fiber textures compared to experimental data. Taking into account the inhomogeneity of the deformation makes it possible to more accurately predict the proportion of cube and β-fiber textures. At the same time, to calculate the amount of Goss texture, the proposed method requires further development.The research was carried out at the expense of a grant from the Russian Science Foundation, project 24-19-00590, https://rscf.ru/project/24-19-00590/.

  • (AlSi)3ScZr nanoparticles formed during cooling down of Al – Mg – Si alloy ingots and their effect on mechanical properties

    by S. V. Konovalov, E. V. Aryshenskiy, M. A. Lapshov, A. M. Drits

    This paper looked at the (AlSi)3ScZr particles that precipitate in Al – Mg – Si alloys with excessive silicon when they are cooling down after casting. The effect of nanoparticles on strength is demonstrated in as-cast state. The effect of artificial ageing on the mechanical properties of studied alloys is also demonstrated. The paper examines six Al – Mg – Si alloys with different Mg/Si ratios and with scandium and zirconium additives or without them. Microhardness and mechanical properties were determined for all alloys in as-cast state. To look at the decomposition of supersaturated solid solution, specimens of alloys containing scandium and zirconium were annealed in the temperature range of 360 to 550 oC, with the soaking time varying between 10 and 50 hours. Using optical microscopy, the grain structure was studied for alloys with Mg/Si = 0.6. Besides, a scanning microscopy study of nanoparticles was conducted for 0.6MgSi0.3Sc0.15Zr alloy. For 0.3MgSi0.3Sc0.15Zr and 0.5MgSi0.3Sc0.15Zr alloys, the data about the grain structure and nanoparticles were taken from previous research studies. The results show that the solid solution supersaturated with scandium, zirconium, silicon and magnesium in the studied alloys has an extremely short decomposition time. It happens because of the combined effect of scandium and silicon. Because of the fast decomposition of the supersaturated solid solution, a great number of (AlSi)3ZrSc particles is formed when it is cooling down after casting. The main mechanism behind it is an intermittent decomposition of the supersaturated solid solution suggested by the presence of fan-shaped particles. Particles detected in the 0.6MgSi0.3Sc0.15Zr alloy retain the L12 structure, are partially coherent with aluminium matrix and contain silicon and scandium. Considering their morphology, sizes and chemical composition, they cannot belong to Sc2Si2Al phase. At the same time, they do impact the mechanical properties. Thus, in the 0.6MgSi0.3Sc0.15Zr alloy the yield strength rises by 43 MPa and the ultimate strength – by 61 MPa. The 0.3MgSi0.3Sc0.15Zr and 0.5MgSi0.3Sc0.15Zr alloys also gain higher strength, which is due to the fan-shaped semi-coherent and round fully coherent (AlSi)3ScZr particles detected in previous research studies in as-cast state. It was found that in the 0.3MgSi0.3Sc0.15Zr and 0.5MgSi0.3Sc0.15Zr alloys the yield strength rises by 32 and 67 MPa and the ultimate strength – by 67 and 78 MPa, respectively. During artificial ageing, microhardness can either rise or drop. The grain structure size produces the strongest effect on microhardness during artificial ageing: the larger the grain size is, the higher the microhardness is after artificial ageing of as-cast material. Support for this research was provided under Grant No. 21-19-00548 https://rscf.ru/project/21-19-00548/ by the Russian Science Foundation.

  • Open Access

    Alloying Elements Effect on the Recrystallization Process in Magnesium-Rich Aluminum Alloy

    by Vladimir Aryshenskii, Fedor Grechnikov, Evgenii Aryshenskii, Yaroslav Erisov, Sergey Konovalov, Maksim Tepterev, Alexander Kuzin

    This paper addresses the study of the complex effect of alloying elements (magnesium, manganese, copper and zirconium) on changes in magnesium-rich aluminum alloy composition, fine and coarse particle size and number, recrystallization characteristics and mechanical properties. The data obtained made it possible to analyze change in the chemical composition, sizes of intermetallic compounds and dispersoids depending on alloying elements content. The effect of the chemical composition on the driving force and the number of recrystallization nuclei was studied. It was established that the addition of alloying elements leads to grain refinement, including through the activation of a particle-stimulated nucleation mechanism. As a result, with Mg increase from 4 to 5%, addition of 0.5% Mn and 0.5% Cu, the grain size decreased from 72 to 15 µm. Grain refinement occurred due to an increase in the number of particle-stimulated nuclei, the number of which at minimal alloying rose from 3.47 × 1011 to 81.2 × 1011 with the maximum concentration of Mg, Mn, Cu additives. The retarding force of recrystallization, which in the original alloy was 1.57 × 10−3 N/m2, increased to 5.49 × 10−3 N/m2 at maximum alloying. The influence of copper was especially noticeable, the introduction of 0.5% increasing the retarding force of recrystallization by 2.39 × 10−3 N/m2. This is due to the fact that copper has the most significant effect on the size and number of intermetallic particles. It was established that strength increase without ductility change occurs when magnesium, manganese and copper content increases.


  • Study of the evolution of crystallographic texture during the drawing of a low-alloyed aluminum alloy

    by E. V. Aryshensky, S. V. Konovalov, I. A. Latushkin, M. A. Lapshov

    The problem of the crystallographic texture evolution in the process of cold stamping of aluminum alloys is considered on the example of the drawing process. For the study, an X-ray diffraction texture analysis of a cold-rolled strip made of a low-alloy aluminum alloy 8011 was carried out. Then, two caps were stamped from the strip with different degrees of deformation, for which the texture composition was also determined. The drawing process of both caps was calculated in the Ansys-LS-Dyna software package in order to establish the stress-strain state. On the basis of these calculations, further modeling of the rotation of texture components characteristic of aluminum after cold deformation was carried out in the TEXT_LATENT_HRD software product. Experimental data showed significant differences in the texture composition of cold-rolled strip and caps. After cold rolling, three typical textures of brass (Bs), S, and Cu, characteristic of the deformed state, are noted; these orientations are manifested with almost the same intensity. At the same time, after drawing, a Goss texture is observed, which is especially pronounced in a high cap; the bs texture practically disappears, and the β textures rotate towards the S orientation. Modeling shows that the components have different stability during the drawing process, for example, Goss and S textures practically do not change their intensity. In this case, the Bs-texture is unstable, the orientations in the space of Euler angles begin to shift from it to the Goss-texture. Such a change differs from that observed during cold rolling in that, as a result of the rotation of the crystal lattice, the material with the Bs orientation acquires the S orientation. Differences in the evolution of texture components during drawing and cold rolling are explained by the difference in the normalized velocity gradients, which has a different effect on the rotation of the crystal lattice at equal plastic deformation by sliding for different crystallographic orientations.The study was supported by a grant from the Russian Science Foundation, project 18-79-10099-P, https://rscf.ru/project/21-79-03041/.


  • Open Access

    Texture Development in Aluminum Alloys with High Magnesium Content

    by Evgenii Aryshenskii, Jurgen Hirsch, Alexander Drits, Sergey Konovalov, Vladimir Aryshenskii, Maksim Tepterev

    The evolution of texture in the AlMg6Mn0.7 (1565 ch) alloy throughout the entire cycle of its thermomechanical treatment has been studied. Using this alloy as an example, a new way is shown to control the texture development, which is applicable to alloys with high magnesium content. An integrated approach is applied, including optical and electron microscopy, as well as X-ray diffraction analysis, the determination of mechanical properties and texture modeling using algorithms of the crystallographic plasticity theory. All stages of the thermomechanical treatment have been studied, namely the development of the deformation structure out of the as-cast structure in the reversing hot-rolling stand, continuous hot rolling, cold rolling and final recrystallization annealing. The study showed that second phase particles are the main source of recrystallization nuclei at all stages of high temperature thermomechanical treatment. The importance of these particles increases when the Zener-Hollomon parameter increases. To obtain the maximum possible proportion of a random texture, thermomechanical processing must be carried out at high Zener-Hollomon parameters. However, the temperature should not interfere with the complete recrystallization process at the same time. After cold rolling and recrystallization annealing at temperatures equal or greater than 350 °C, a large proportion of random texture is formed, and the properties of the metal are almost isotropic.


  • Open Access

    The Casting Rate Impact on the Microstructure in Al–Mg–Si Alloy with Silicon Excess and Small Zr, Sc Additives

    by Evgenii Aryshenskii, Maksim Lapshov, Sergey Konovalov, Jurgen Hirsch, Vladimir Aryshenskii, Svetlana Sbitneva

    The study investigates the effect of casting speed on the solidification microstructure of the aluminum alloy Al0.3Mg1Si with and without the additions of zirconium and scandium. Casting was carried out in steel, copper, and water-cooled chill molds with a crystallization rate of 20 °C/s, 10 °C/s, and 30 °C/s, respectively. For each casting mode, the grain structure was investigated by optical microscopy and the intermetallic particles were investigated by scanning and transmission microscopy; in addition, measurements of the microhardness and the electrical conductivity were carried out. An increase in the solidification rate promotes grain refinement in both alloys. At the same time, the ingot cooling rate differently affects the number of intermetallic particles. In an alloy without scandium–zirconium additives, an increase in the ingot cooling rate leads to a decrease in the number of dispersoids due to an increase in the solubility of the alloying elements in a supersaturated solid solution. With the addition of scandium and zirconium, the amount of dispersoids increases slightly. This is because increasing the solubility of the alloying elements in a supersaturated solid solution is leveled by a growth of the number of grain boundaries, promoting the formation of particles of the (AlSi)3ScZr type, including those of the L12 type. In addition, the increase in the crystallization rate increases the number of primary nonequilibrium intermetallic particles which have a eutectic nature.


  • Open Access

    Influence of the Small Sc and Zr Additions on the As-Cast Microstructure of Al–Mg–Si Alloys with Excess Silicon

    by Evgenii Aryshenskii, Maksim Lapshov, Jurgen Hirsch, Sergey Konovalov, Viacheslav Bazhenov, Alexander Drits, Denis Zaitsev

    This research is devoted to the study effects of complex alloying of Al-0.3 wt. % Mg-1 wt. % Si and Al-0.5 wt. % Mg-1.3 wt. % Si alloys by small additions of Sc and Zr on the microstructure in the as-cast condition. The effect of small additions of these elements on the microhardness, electrical conductivity, grain size and phase composition of the indicated alloy systems was studied. The methods of optical and electron microscopy were used for the study. Moreover, the phase composition was calculated using the Thermo-Calc software package. The study showed a strong effect of the chemical composition of investigated alloys on the size of the grains, which, with a certain combination of additives, can decrease several times. Grain refinement occurs both due to supercooling and formation of primary Al3Sc particles in the liquid phase. Alloys based on Al-0.5 wt. % Mg-1.3 wt. % Si are more prone to the formation of this phase since a lower concentration of Sc is required for it to occur. In addition, more silicon interacts with other elements. At the same time, Al-0.3 wt. % Mg-1 wt. % Si requires lower temperature for complete dissolution of Mg2Si, which can contribute to more efficient heat treatment, which includes reducing the number of steps. TEM data show that during ingot cooling (AlSi)3ScZr dispersoid precipitates. This dispersoid could precipitate as coherent and semi-coherent particles with L12 structure as well as needle-shaped particles. The precipitation of coherent and semi-coherent particles during cooling of the ingot indicates that they can be obtained during subsequent multistage heat treatment. In addition, in the Al0.5Mg1.3Si0.3Sc alloy, metastable β″ (Mg5Si6) are precipitated.


  • Open Access

    Influence of Mg Content on Texture Development during Hot Plain-Strain Deformation of Aluminum Alloys

    by Evgenii Aryshenskii, Jurgen Hirsch, Sergey Konovalov, Vladimir Aryshenskii, Alexander Drits

    The study addresses the effect of magnesium and other alloying elements on rolling “β-fiber” texture formation during hot deformation of aluminum alloys. For the study, flat cast ingots from three aluminum alloys with variable magnesium content were deformed in a Gleeble testing unit with different parameters of thermomechanical treatment. Immediately after completion of deformation, the samples were quenched using an automatic cooling system and the microstructure and crystalline texture was analyzed by optical microscopy and X-ray analysis. The analysis demonstrated that an increase in alloying components, magnesium in particular, leads to an increase in brass-type texture and a decrease in S and copper-type texture. The reason was that the simulation of the deformation texture development revealed a great contribution of impurity atoms rather than the decrease in stacking fault energy.


  • Open Access

    Investigation of the Intermetallic Compounds Fragmentation Impact on the Formation of Texture during the as Cast Structure Thermomechanical Treatment of Aluminum Alloys

    by Evgenii Aryshenskii, Jurgen Hirsch, Sergey Konovalov

    In this work, the influence of the intermetallic particle fragmentation during hot rolling of the as cast structure on the evolution of textures in aluminum alloys 8011, 5182 and 1565 was investigated. For this purpose, laboratory multi-pass rolling of the cast material was carried out. At various degrees of hot rolling deformation, the process was stopped, and the metal was quenched and sent for optical and electron microscopy to investigate the large intermetallic particles. In addition, the grain structure was studied and an X-ray analysis was carried out in order to determine the main texture components. Some of the samples were held at a temperature above the recrystallization threshold and then cooled in air; the grain structure and texture composition were also studied. In addition, the simulation of the texture evolution was carried out under various modes of rolling of aluminum alloys, taking into account the process of fragmentation of intermetallic particles. The investigation showed that intermetallic compounds with a deformation degree of 1.8, on average, decrease the particle size by 5–7 times. The large eutectic particles remaining after homogenization are drawn out in the direction of deformation and are crushed, increasing their number accordingly. Therefore, the most favorable stage for the formation of recrystallization nuclei on particles is the moment when they are already numerous and their sizes are much larger than subgrains. Simulation of hot rolling of the investigated alloys showed that considering the factor of fragmentation of intermetallic particles during hot deformation of the as-cast structure significantly increases the accuracy of the results.