Seyyed Sadegh Ghasemi Banadkouki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Seyyed Sadegh Ghasemi Banadkouki has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Mahesh Chandra Somani
University of Oulu
6 shared publications - Ali Khajesarvi
Department of Mining and Metallurgical Engineering, Yazd University, Yazd, Iran
3 shared publications - Hamid Reza Karimi Zarchi
Department of Mining and Metallurgical Engineering, Yazd University, University Blvd, Safayieh, Yazd, PO Box: 98195 – 741, Iran, Tel: +98 9132528680; Fax: +98 35 38210995
3 shared publications - Shima Pashangeh
Materials Engineering Department, School of Engineering, Yasouj University, Yasouj, Iran
3 shared publications Jukka Kömi
Materials and Mechanical Engineering Centre for Advanced Steels Research University of Oulu 90014 Oulun Yliopisto Finland
2 shared publications- Jukka Kömi
University of Oulu
2 shared publications
Latest Publications
- Open Access
- 21 August 2025
- Published by Science Publishing Group in International Journal of Mineral Processing and Extractive Metallurgy
- Vol. 10 (2) , 49-56
Identification of Bainite and Martensite Phases in Cold Work Tool Steel D3 Using Color Metallography
Background: AISI D3 cold-work tool steel is a high-carbon, high-chromium alloy renowned for its exceptional wear resistance and hardness, making it crucial for applications such as dies and cutting tools. The performance of this steel is intrinsically linked to its microstructure, which, depending on the heat treatment, can be a complex mixture of primary carbides, martensite, bainite, and pearlite. Accurate identification and differentiation of these phases are essential for quality control and predicting material behavior. Objective: This research aims to systematically evaluate the efficacy of various color metallography techniques for the clear identification and differentiation of bainite, martensite, and other micro-constituents in annealed D3 tool steel. This study highlights a cost-effective alternative to more advanced and expensive characterization methods like electron microscopy. Methods: Samples of D3 steel were subjected to an annealing heat treatment cycle, involving austenitizing at 1000°C followed by slow furnace cooling, to generate a multi-phase microstructure. Standard metallographic preparation was followed by the application of several chemical etchants. Single-stage etching techniques using Nital, Vilella, Sodium Metabisulfite, and Marshall’s reagent were employed, alongside two-stage techniques combining Nital with Marble’s reagent and Nital with Sodium Metabisulfite. The resulting microstructures were analyzed using optical microscopy. Furthermore, quantitative phase analysis was performed using image analysis software to determine the volume fraction of each constituent. Results: The findings indicated that while single-stage etching with Nital or Vilella could identify carbides, they failed to distinguish between bainite and martensite. The two-stage technique using Nital followed by Marble’s reagent provided excellent differentiation between carbides, martensite (light brown), and bainite (bright green). However, the most effective overall technique was single-stage etching with aqueous sodium metabisulfite, which successfully revealed all micro-constituents-carbides, martensite, bainite, and pearlite-simultaneously with superior contrast and clarity. Quantitative analysis revealed a microstructure composed of approximately 18% carbides, 55% martensite, 22% bainite, and 5% pearlite. Color metallography, particularly using sodium metabisulfite, proves to be a highly effective, rapid, and economical method for the comprehensive microstructural analysis of D3 tool steel. The developed techniques provide a reliable tool for phase identification in high-chromium tool steels, facilitating process control and material development.
- 21 August 2025
- Published by Science Publishing Group in International Journal of Mineral Processing and Extractive Metallurgy
- Vol. 10 (2) , 49-56
Open AccessIdentification of Bainite and Martensite Phases in Cold Work Tool Steel D3 Using Color Metallography
Background: AISI D3 cold-work tool steel is a high-carbon, high-chromium alloy renowned for its exceptional wear resistance and hardness, making it crucial for applications such as dies and cutting tools. The performance of this steel is intrinsically linked to its microstructure, which, depending on the heat treatment, can be a complex mixture of primary carbides, martensite, bainite, and pearlite. Accurate identification and differentiation of these phases are essential for quality control and predicting material behavior. Objective: This research aims to systematically evaluate the efficacy of various color metallography techniques for the clear identification and differentiation of bainite, martensite, and other micro-constituents in annealed D3 tool steel. This study highlights a cost-effective alternative to more advanced and expensive characterization methods like electron microscopy. Methods: Samples of D3 steel were subjected to an annealing heat treatment cycle, involving austenitizing at 1000°C followed by slow furnace cooling, to generate a multi-phase microstructure. Standard metallographic preparation was followed by the application of several chemical etchants. Single-stage etching techniques using Nital, Vilella, Sodium Metabisulfite, and Marshall’s reagent were employed, alongside two-stage techniques combining Nital with Marble’s reagent and Nital with Sodium Metabisulfite. The resulting microstructures were analyzed using optical microscopy. Furthermore, quantitative phase analysis was performed using image analysis software to determine the volume fraction of each constituent. Results: The findings indicated that while single-stage etching with Nital or Vilella could identify carbides, they failed to distinguish between bainite and martensite. The two-stage technique using Nital followed by Marble’s reagent provided excellent differentiation between carbides, martensite (light brown), and bainite (bright green). However, the most effective overall technique was single-stage etching with aqueous sodium metabisulfite, which successfully revealed all micro-constituents-carbides, martensite, bainite, and pearlite-simultaneously with superior contrast and clarity. Quantitative analysis revealed a microstructure composed of approximately 18% carbides, 55% martensite, 22% bainite, and 5% pearlite. Color metallography, particularly using sodium metabisulfite, proves to be a highly effective, rapid, and economical method for the comprehensive microstructural analysis of D3 tool steel. The developed techniques provide a reliable tool for phase identification in high-chromium tool steels, facilitating process control and material development.
- 2 January 2024
- Published by Wiley in Steel Research International
- Vol. 95 (3)
Investigation of Micromechanical Properties of Martensite and Ferrite Microphases in a 35CHGSA Medium‐Si Low‐Alloy Steel
The purpose of this study is to understand in detail the micromechanical behavior of martensite and ferrite microphases in a medium‐Si 35CHGSA dual‐phase (DP) steel by varying the martensite volume fractions (MVF) and ferrite phase constituents. Light microscopy combined with microhardness measurements is supplemented by field‐emission scanning electron microscopy, electron backscatter diffraction, transmission electron microscopy, and X‐ray diffraction in order to evaluate the micromechanical behavior of martensite and ferrite microphases in relation to the evolving microstructure. The experimental observations illustrate that ferrite microhardness diminishes sharply from 352 to 217 HV5g with the change in ferrite volume fraction (FVF) from 3 to 13%, beyond which it increases abnormally to 245 HV5g with a further increase in VF to 15%. The martensite microhardness too varies significantly depending on the progress of ferrite formation in the intercritical range. The hardness drops with further increase in FVF as a result of longer holding times. These observations are rationalized in part to the mutual interaction of martensite with ferrite, and the variation of martensite and ferrite alloying concentrations, developed as a result of ferrite formation during intercritical holding at 720 °C.
- 2 January 2024
- Published by Wiley in Steel Research International
- Vol. 95 (3)
Investigation of Micromechanical Properties of Martensite and Ferrite Microphases in a 35CHGSA Medium‐Si Low‐Alloy Steel
The purpose of this study is to understand in detail the micromechanical behavior of martensite and ferrite microphases in a medium‐Si 35CHGSA dual‐phase (DP) steel by varying the martensite volume fractions (MVF) and ferrite phase constituents. Light microscopy combined with microhardness measurements is supplemented by field‐emission scanning electron microscopy, electron backscatter diffraction, transmission electron microscopy, and X‐ray diffraction in order to evaluate the micromechanical behavior of martensite and ferrite microphases in relation to the evolving microstructure. The experimental observations illustrate that ferrite microhardness diminishes sharply from 352 to 217 HV5g with the change in ferrite volume fraction (FVF) from 3 to 13%, beyond which it increases abnormally to 245 HV5g with a further increase in VF to 15%. The martensite microhardness too varies significantly depending on the progress of ferrite formation in the intercritical range. The hardness drops with further increase in FVF as a result of longer holding times. These observations are rationalized in part to the mutual interaction of martensite with ferrite, and the variation of martensite and ferrite alloying concentrations, developed as a result of ferrite formation during intercritical holding at 720 °C.
- 30 May 2023
- Published by Walter de Gruyter GmbH in HTM Journal of Heat Treatment and Materials
- Vol. 78 (3) , 141-161
Effect of Carbon Partitioning on Abnormal Martensite Hardening in a Conventional Quench and Temper Medium Silicon Low Alloy Steel under Ferrite-Martensite Dual-Phase Microstructure
The purpose of this research work was to investigate the effect of carbon partitioning within ferrite and prior austenite (martensite) during progress of ferrite formation and consequently its relation to the associated martensite hardening in a medium silicon low alloy conventional quench and temper steel. For this aim, several ferrite-martensite dual-phase (DP) samples containing various volume fractions of ferrite and martensite microphases were developed. The X-ray diffraction and electron microscopy with spot and line-scan X-ray energy-dispersive spectroscopy (EDS) for carbon analysis were used in conjunction with light microscopy and hardness test to follow the variation of carbon partitioning within ferrite and prior austenite (martensite) regions and consequently the associated martensite hardening in the DP samples.
- 30 May 2023
- Published by Walter de Gruyter GmbH in HTM Journal of Heat Treatment and Materials
- Vol. 78 (3) , 141-161
Effect of Carbon Partitioning on Abnormal Martensite Hardening in a Conventional Quench and Temper Medium Silicon Low Alloy Steel under Ferrite-Martensite Dual-Phase Microstructure
The purpose of this research work was to investigate the effect of carbon partitioning within ferrite and prior austenite (martensite) during progress of ferrite formation and consequently its relation to the associated martensite hardening in a medium silicon low alloy conventional quench and temper steel. For this aim, several ferrite-martensite dual-phase (DP) samples containing various volume fractions of ferrite and martensite microphases were developed. The X-ray diffraction and electron microscopy with spot and line-scan X-ray energy-dispersive spectroscopy (EDS) for carbon analysis were used in conjunction with light microscopy and hardness test to follow the variation of carbon partitioning within ferrite and prior austenite (martensite) regions and consequently the associated martensite hardening in the DP samples.
- Open Access
Abnormal Trend of Ferrite Hardening in a Medium-Si Ferrite-Martensite Dual Phase Steel
In this paper, the effects of carbon, Si, Cr and Mn partitioning on ferrite hardening were studied in detail using a medium Si low alloy grade of 35CHGSA steel under ferrite-martensite/ferrite-pearlite dual-phase (DP) condition. The experimental results illustrated that an abnormal trend of ferrite hardening had occurred with the progress of ferrite formation. At first, the ferrite microhardness decreased with increasing volume fraction of ferrite, thereby reaching the minimum value for a moderate ferrite formation, and then it surprisingly increased with subsequent increase in ferrite volume fraction. Beside a considerable influence of martensitic phase transformation induced residual compressive stresses within ferrite, these results were further rationalized in respect of the extent of carbon, Si, Cr and Mn partitioning between ferrite and prior austenite (martensite) microphases leading to the solid solution hardening effects of these elements on ferrite.
Open AccessAbnormal Trend of Ferrite Hardening in a Medium-Si Ferrite-Martensite Dual Phase Steel
In this paper, the effects of carbon, Si, Cr and Mn partitioning on ferrite hardening were studied in detail using a medium Si low alloy grade of 35CHGSA steel under ferrite-martensite/ferrite-pearlite dual-phase (DP) condition. The experimental results illustrated that an abnormal trend of ferrite hardening had occurred with the progress of ferrite formation. At first, the ferrite microhardness decreased with increasing volume fraction of ferrite, thereby reaching the minimum value for a moderate ferrite formation, and then it surprisingly increased with subsequent increase in ferrite volume fraction. Beside a considerable influence of martensitic phase transformation induced residual compressive stresses within ferrite, these results were further rationalized in respect of the extent of carbon, Si, Cr and Mn partitioning between ferrite and prior austenite (martensite) microphases leading to the solid solution hardening effects of these elements on ferrite.
- Open Access
Characteristics and Kinetics of Bainite Transformation Behaviour in a High-Silicon Medium-Carbon Steel above and below the Ms Temperature
This work deals with the kinetic aspects of bainite formation during isothermal holding above and below the martensite start (Ms~275 °C) temperature using a low-alloy, high-silicon DIN 1.5025 steel in a range suitable for achieving ultrafine/nanostructured bainite. Dilatation measurements were conducted to study transformation behaviour and kinetics, while the microstructural features were examined using laser scanning confocal microscopy and electron backscatter diffraction (EBSD) techniques combined with hardness measurements. The results showed that for isothermal holding above the Ms temperature, the maximum bainitic transformation rate decreased with the decrease in isothermal holding temperature between 450 and 300 °C. On the other hand, for isothermal holding below the Ms temperature at 250 and 200 °C, the maximum rate of transformation was achieved corresponding to region I due to the partitioning of carbon and also possibly because of the ledged growth of isothermal martensite soon after the start of isothermal holding. In addition, a second peak was obvious at about 100 and 500 s, respectively, during holding at 250 and 200 °C due to the occurrence of bainitic transformation, marking the beginning of region II.
Open AccessCharacteristics and Kinetics of Bainite Transformation Behaviour in a High-Silicon Medium-Carbon Steel above and below the Ms Temperature
This work deals with the kinetic aspects of bainite formation during isothermal holding above and below the martensite start (Ms~275 °C) temperature using a low-alloy, high-silicon DIN 1.5025 steel in a range suitable for achieving ultrafine/nanostructured bainite. Dilatation measurements were conducted to study transformation behaviour and kinetics, while the microstructural features were examined using laser scanning confocal microscopy and electron backscatter diffraction (EBSD) techniques combined with hardness measurements. The results showed that for isothermal holding above the Ms temperature, the maximum bainitic transformation rate decreased with the decrease in isothermal holding temperature between 450 and 300 °C. On the other hand, for isothermal holding below the Ms temperature at 250 and 200 °C, the maximum rate of transformation was achieved corresponding to region I due to the partitioning of carbon and also possibly because of the ledged growth of isothermal martensite soon after the start of isothermal holding. In addition, a second peak was obvious at about 100 and 500 s, respectively, during holding at 250 and 200 °C due to the occurrence of bainitic transformation, marking the beginning of region II.
- 8 October 2021
- Published by Wiley in Steel Research International
- Vol. 93 (4)
Effect of Carbon Partitioning and Residual Compressive Stresses on the Lattice Strains of Retained Austenite During Quenching and Isothermal Bainitic Holding in a High‐Silicon Medium‐Carbon Steel
The residual compressive stresses and dimensional changes related to the lattice strains of retained austenite (RA) phase in a high‐Si, medium‐carbon steel (Fe‐0.53C‐1.67Si‐0.72Mn‐0.12Cr) are investigated for samples austenitized and quenched for isothermal bainitic transformation (Q&B) in the range 5 s to 1 h at 350 °C. Also, samples are directly quenched in water (DWQ) from the austenitization temperature for comparison with Q&B samples. Field emission scanning electron microscopy (FE‐SEM) combined with electron backscatter diffraction (EBSD) analyses, and X‐ray diffraction are used to investigate the microstructural evolution, phase distribution, and lattice parameters of RA phase. While the Q&B samples showed formation of bainite and high‐carbon fresh martensite in conjunction with stabilization of various fractions of RA, the DWQ samples displayed nearly complete martensitic microstructure. For short holding durations (≪200 s), there was limited formation of bainite and the inadequate carbon partitioning to the adjacent untransformed austenite areas resulted in significant martensite formation and the associated c/a ratio of martensite resulted in high compressive residual stresses within the RA phase. While, at long isothermal holding times (≫ 200 s), there was a significant formation of bainite. The DWQ samples displayed maximum lattice strain in a small fraction of untransformed RA phase.
- 8 October 2021
- Published by Wiley in Steel Research International
- Vol. 93 (4)
Effect of Carbon Partitioning and Residual Compressive Stresses on the Lattice Strains of Retained Austenite During Quenching and Isothermal Bainitic Holding in a High‐Silicon Medium‐Carbon Steel
The residual compressive stresses and dimensional changes related to the lattice strains of retained austenite (RA) phase in a high‐Si, medium‐carbon steel (Fe‐0.53C‐1.67Si‐0.72Mn‐0.12Cr) are investigated for samples austenitized and quenched for isothermal bainitic transformation (Q&B) in the range 5 s to 1 h at 350 °C. Also, samples are directly quenched in water (DWQ) from the austenitization temperature for comparison with Q&B samples. Field emission scanning electron microscopy (FE‐SEM) combined with electron backscatter diffraction (EBSD) analyses, and X‐ray diffraction are used to investigate the microstructural evolution, phase distribution, and lattice parameters of RA phase. While the Q&B samples showed formation of bainite and high‐carbon fresh martensite in conjunction with stabilization of various fractions of RA, the DWQ samples displayed nearly complete martensitic microstructure. For short holding durations (≪200 s), there was limited formation of bainite and the inadequate carbon partitioning to the adjacent untransformed austenite areas resulted in significant martensite formation and the associated c/a ratio of martensite resulted in high compressive residual stresses within the RA phase. While, at long isothermal holding times (≫ 200 s), there was a significant formation of bainite. The DWQ samples displayed maximum lattice strain in a small fraction of untransformed RA phase.
- 1 October 2021
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 10 (5) , 610-626
Effect of Ferrite and Martensite Hardening Variation on Mechanism of Void Formation in Low-Alloy Dual-Phase Steel
- 1 October 2021
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 10 (5) , 610-626
Effect of Ferrite and Martensite Hardening Variation on Mechanism of Void Formation in Low-Alloy Dual-Phase Steel
- Open Access
Color Light Metallography Versus Electron Microscopy for Detecting and Estimating Various Phases in a High-Strength Multiphase Steel
In this study, fresh attempts have been made to identify and estimate the phase constituents of a high-silicon, medium carbon multiphase steel (DIN 1.5025 grade) subjected to austenitization at 900 °C for 5 min, followed by quenching and low-temperature bainitizing (Q&B) at 350 °C for 200 s. Several techniques were employed using different chemical etching reagents either individually (single-step) or in combination of two or more etchants in succession (multiple-step) for conducting color metallography. The results showed that the complex multiphase microstructures comprising a fine mixture of bainite, martensite and retained austenite phase constituents were selectivity stained/tinted with good contrasting resolution, as observed via conventional light optical microscopy observations. While the carbon-enriched martensite-retained austenite (M/RA) islands were revealed as cream-colored areas by using a double-step etching technique comprising etching with 10% ammonium persulfate followed by etching with Marble’s reagent, the dark gray-colored bainite packets were easily distinguishable from the brown-colored martensite regions. However, the high-carbon martensite and retained austenite in M/RA islands could be differentiated only after resorting to a triple-step etching technique comprising etching in succession with 2% nital, 10% ammonium persulfate solution and then warm Marble’s reagent at 30 °C. This revealed orange-colored martensite in contrast to cream-colored retained austenite in M/RA constituents, besides the presence of brown-colored martensite laths in the dark gray-colored bainitic matrix. A quadruple-step technique involving successive etching with 2% nital, 10% ammonium persulfate solution, Marble’s reagent and finally Klemm’s Ι reagent at 40 °C revealed even better contrast in comparison to the triple-step etching technique, particularly in distinguishing the RA from martensite. Observations using advanced techniques like field emission scanning electron microscopy (FE-SEM) and electron back scatter diffraction (EBSD) failed to differentiate untempered, high-carbon martensite from retained austenite in the M/RA islands and martensite laths from bainitic matrix, respectively. Transmission electron microscopy (TEM) studies successfully distinguished the RA from high-carbon martensite, as noticed in M/RA islands. The volume fraction of retained austenite estimated by EBSD, XRD and a point counting method on color micrographs of quadruple-step etched samples showed good agreement.
Open AccessColor Light Metallography Versus Electron Microscopy for Detecting and Estimating Various Phases in a High-Strength Multiphase Steel
In this study, fresh attempts have been made to identify and estimate the phase constituents of a high-silicon, medium carbon multiphase steel (DIN 1.5025 grade) subjected to austenitization at 900 °C for 5 min, followed by quenching and low-temperature bainitizing (Q&B) at 350 °C for 200 s. Several techniques were employed using different chemical etching reagents either individually (single-step) or in combination of two or more etchants in succession (multiple-step) for conducting color metallography. The results showed that the complex multiphase microstructures comprising a fine mixture of bainite, martensite and retained austenite phase constituents were selectivity stained/tinted with good contrasting resolution, as observed via conventional light optical microscopy observations. While the carbon-enriched martensite-retained austenite (M/RA) islands were revealed as cream-colored areas by using a double-step etching technique comprising etching with 10% ammonium persulfate followed by etching with Marble’s reagent, the dark gray-colored bainite packets were easily distinguishable from the brown-colored martensite regions. However, the high-carbon martensite and retained austenite in M/RA islands could be differentiated only after resorting to a triple-step etching technique comprising etching in succession with 2% nital, 10% ammonium persulfate solution and then warm Marble’s reagent at 30 °C. This revealed orange-colored martensite in contrast to cream-colored retained austenite in M/RA constituents, besides the presence of brown-colored martensite laths in the dark gray-colored bainitic matrix. A quadruple-step technique involving successive etching with 2% nital, 10% ammonium persulfate solution, Marble’s reagent and finally Klemm’s Ι reagent at 40 °C revealed even better contrast in comparison to the triple-step etching technique, particularly in distinguishing the RA from martensite. Observations using advanced techniques like field emission scanning electron microscopy (FE-SEM) and electron back scatter diffraction (EBSD) failed to differentiate untempered, high-carbon martensite from retained austenite in the M/RA islands and martensite laths from bainitic matrix, respectively. Transmission electron microscopy (TEM) studies successfully distinguished the RA from high-carbon martensite, as noticed in M/RA islands. The volume fraction of retained austenite estimated by EBSD, XRD and a point counting method on color micrographs of quadruple-step etched samples showed good agreement.
- Open Access
- 26 November 2019
- Published by Walter de Gruyter GmbH in REVIEWS ON ADVANCED MATERIALS SCIENCE
- Vol. 58 (1) , 206-217
Microstructural Evolution and Carbon Partitioning in Interstitial Free Weld Simulated API 5L X60 Steel
The microstructural characterizations and partitioning of carbon element in the weld heat affected zones of a commercial API 5L X60 line pipe steel were studied by applying a high speed heating and cooling dilatometry technique in the present research work. The hollow cylindrical specimens were quickly heated to 1000°C, soaked for only 5 s followed by continuous cooling to ambient temperature. Besides the construction of CCT diagram of this high strength low alloy steel using the dilatation data, the hardening response, microstructural features and carbon partitioning of weld simulated specimens were investigated. The obtained results showed that the hardening response of samples increased from 142 to 261HV10kg with increasing cooling rates. These hardening variations were attributed to the changes in microstructural features and carbon partitioning that occurred between the microconstituents present in the microstructures of weld simulated samples.
- 26 November 2019
- Published by Walter de Gruyter GmbH in REVIEWS ON ADVANCED MATERIALS SCIENCE
- Vol. 58 (1) , 206-217
Open AccessMicrostructural Evolution and Carbon Partitioning in Interstitial Free Weld Simulated API 5L X60 Steel
The microstructural characterizations and partitioning of carbon element in the weld heat affected zones of a commercial API 5L X60 line pipe steel were studied by applying a high speed heating and cooling dilatometry technique in the present research work. The hollow cylindrical specimens were quickly heated to 1000°C, soaked for only 5 s followed by continuous cooling to ambient temperature. Besides the construction of CCT diagram of this high strength low alloy steel using the dilatation data, the hardening response, microstructural features and carbon partitioning of weld simulated specimens were investigated. The obtained results showed that the hardening response of samples increased from 142 to 261HV10kg with increasing cooling rates. These hardening variations were attributed to the changes in microstructural features and carbon partitioning that occurred between the microconstituents present in the microstructures of weld simulated samples.