Katia Devriendt
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Katia Devriendt has a total of 310 co-authors. Here are the top co-authors by number of shared publications:
D. Mocuta
6 shared publicationsB. T. Chan
IMEC, Leuven, Belgium
5 shared publicationsE. Vecchio
IMEC,Leuven,Belgium,3001
5 shared publicationsF. Sebaai
IMEC, Leuven, Belgium
5 shared publicationsN. Horiguchi
IMEC, Leuven, Belgium
5 shared publicationsA. Hikavyy
IMEC, Leuven, Belgium
4 shared publications
Latest Publications
- 29 September 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (6)
Plasma etching behavior of iridium in CF4- and Cl2-based chemistries
Iridium (Ir) is a chemically stable noble metal that remains difficult to etch with high controllability under plasma processing conditions due to its low volatility and limited chemical reactivity. In this work, Ir plasma etching under fluorine- and chlorine-based chemistries is systematically investigated to examine the distinct ion–surface interaction behaviors governing material removal under different plasma conditions. Variations in transformer-coupled plasma (TCP) power and substrate bias voltage reveal markedly different etch-rate scaling characteristics for CF4/O2 and Cl2/O2/Ar plasmas, particularly with respect to substrate bias. In CF4-based plasmas, the Ir etch rate increases monotonically with both TCP power and bias voltage, consistent with a sustained ion-assisted etching response. In contrast, Cl2-based plasmas exhibit progressively reduced etch-rate sensitivity to substrate bias at higher voltages. Gas composition further modifies the etching characteristics through the contrasting role of oxygen in the two plasma chemistries. In CF4-based plasmas, O2 suppresses fluorocarbon accumulation and sustains Ir removal, whereas in Cl2-based plasmas, increasing O2 content reduces the etch rate and promotes surface-constrained etching conditions. X-ray photoelectron spectroscopy reveals distinct surface chemical states for CF4- and Cl2-based plasmas, while transmission electron microscopy shows substantially more aggressive material removal under CF4-based conditions. Overall, the results demonstrate that Ir etching is governed by the interplay between ion-assisted removal and chemistry-dependent surface limitations in fluorine- and chlorine-based plasmas.
- 29 September 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (6)
Plasma etching behavior of iridium in CF4- and Cl2-based chemistries
Iridium (Ir) is a chemically stable noble metal that remains difficult to etch with high controllability under plasma processing conditions due to its low volatility and limited chemical reactivity. In this work, Ir plasma etching under fluorine- and chlorine-based chemistries is systematically investigated to examine the distinct ion–surface interaction behaviors governing material removal under different plasma conditions. Variations in transformer-coupled plasma (TCP) power and substrate bias voltage reveal markedly different etch-rate scaling characteristics for CF4/O2 and Cl2/O2/Ar plasmas, particularly with respect to substrate bias. In CF4-based plasmas, the Ir etch rate increases monotonically with both TCP power and bias voltage, consistent with a sustained ion-assisted etching response. In contrast, Cl2-based plasmas exhibit progressively reduced etch-rate sensitivity to substrate bias at higher voltages. Gas composition further modifies the etching characteristics through the contrasting role of oxygen in the two plasma chemistries. In CF4-based plasmas, O2 suppresses fluorocarbon accumulation and sustains Ir removal, whereas in Cl2-based plasmas, increasing O2 content reduces the etch rate and promotes surface-constrained etching conditions. X-ray photoelectron spectroscopy reveals distinct surface chemical states for CF4- and Cl2-based plasmas, while transmission electron microscopy shows substantially more aggressive material removal under CF4-based conditions. Overall, the results demonstrate that Ir etching is governed by the interplay between ion-assisted removal and chemistry-dependent surface limitations in fluorine- and chlorine-based plasmas.
- 1 July 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 44 (4)
Through-silicon via etch uniformity enhancement and aspect-ratio influence on etch rate and profile
High-aspect ratio (HAR) through-silicon via (TSV) etching is a critical process for three-dimensional interconnect (3Di) integration, requiring strict within-wafer (WiW) depth uniformity and profile stability. In this study, we systematically investigated TSV profile and WiW uniformity by varying process parameters in a conventional inductively coupled plasma (ICP) etch system, without employing hardware level uniformity control. A stable baseline process was initially established for TSVs with a critical dimension of 5 μm at an aspect ratio (AR) of 10, achieving uniform etch depth and straight via profiles with vertical sidewalls across the wafer. Using this baseline as a reference, the impact of increasing AR was examined. As the etch depth increased, the measured average etch rate exhibited an exponential decrease, indicating increasingly pronounced transport limitations. At AR 15, competing requirements for entrance profile stability and effective bottom etching became evident, leading to a clear trade-off depending on process optimization strategy. At higher AR 20, severe profile degradation and wafer-level nonuniformity emerged, including pronounced bowing, tapering, and localized etch-stop behavior near the wafer edge. These results provide experimental insight into the limitations of parameter-only optimization in standard ICP etch chambers under extreme HAR conditions.
- 1 July 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 44 (4)
Through-silicon via etch uniformity enhancement and aspect-ratio influence on etch rate and profile
High-aspect ratio (HAR) through-silicon via (TSV) etching is a critical process for three-dimensional interconnect (3Di) integration, requiring strict within-wafer (WiW) depth uniformity and profile stability. In this study, we systematically investigated TSV profile and WiW uniformity by varying process parameters in a conventional inductively coupled plasma (ICP) etch system, without employing hardware level uniformity control. A stable baseline process was initially established for TSVs with a critical dimension of 5 μm at an aspect ratio (AR) of 10, achieving uniform etch depth and straight via profiles with vertical sidewalls across the wafer. Using this baseline as a reference, the impact of increasing AR was examined. As the etch depth increased, the measured average etch rate exhibited an exponential decrease, indicating increasingly pronounced transport limitations. At AR 15, competing requirements for entrance profile stability and effective bottom etching became evident, leading to a clear trade-off depending on process optimization strategy. At higher AR 20, severe profile degradation and wafer-level nonuniformity emerged, including pronounced bowing, tapering, and localized etch-stop behavior near the wafer edge. These results provide experimental insight into the limitations of parameter-only optimization in standard ICP etch chambers under extreme HAR conditions.
- Open Access
- 1 June 2026
- Published by AIP Publishing in APL Photonics
- Vol. 11 (6)
Transfer-matrix modeling of spectral reflectivity for monitoring reactive-ion etching processes
We apply the transfer matrix method (TMM) to model the evolution of light spectral reflectivity during reactive ion etching of SiGe heterostructures used in electro-absorption modulators. The simulated reflectivity as a function of etch depth shows excellent agreement with in situ light spectral reflectometry measurements, enabling identification of wavelength ranges most sensitive to changes in the quantum-well (QW) stack. For Ge-rich SiGe (∼80% Ge), both modeling and experiment indicate a sensitivity window centered near 500 ± 50 nm, where the QW heterostructure exhibits a distinct spectral signature. We further show that introducing a thin SiGe etch-contrast layer (ECL) with ∼10% Ge concentration offset from the strain-relaxed buffer composition produces a clear reflectivity response that simplifies end point determination. These results demonstrate how TMM-assisted wavelength selection and ECL engineering can enhance the robustness of etch end point algorithms for advanced SiGe photonic device fabrication.
- 1 June 2026
- Published by AIP Publishing in APL Photonics
- Vol. 11 (6)
Open AccessTransfer-matrix modeling of spectral reflectivity for monitoring reactive-ion etching processes
We apply the transfer matrix method (TMM) to model the evolution of light spectral reflectivity during reactive ion etching of SiGe heterostructures used in electro-absorption modulators. The simulated reflectivity as a function of etch depth shows excellent agreement with in situ light spectral reflectometry measurements, enabling identification of wavelength ranges most sensitive to changes in the quantum-well (QW) stack. For Ge-rich SiGe (∼80% Ge), both modeling and experiment indicate a sensitivity window centered near 500 ± 50 nm, where the QW heterostructure exhibits a distinct spectral signature. We further show that introducing a thin SiGe etch-contrast layer (ECL) with ∼10% Ge concentration offset from the strain-relaxed buffer composition produces a clear reflectivity response that simplifies end point determination. These results demonstrate how TMM-assisted wavelength selection and ECL engineering can enhance the robustness of etch end point algorithms for advanced SiGe photonic device fabrication.
- 24 March 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (3)
Sputter yield and stoichiometry study of InGaZnO film in ion beam etching
Although extensive research has been conducted on the characteristics of ion beam etching, studies focusing on sputtering yield at low ion energies and the effects of etching on material properties remain limited. In this study, the etching characteristics of InGaZnO4 (IGZO) thin films were investigated using Ar+ ion beams at various ion energies (50–800 eV) and incident angles (0°–87°). At ion energies below 100 eV, the sputter yield continuously increased with the incident angle across the entire range. This phenomenon differs from the established relationship observed at higher ion energies and may be attributed to surface collision dominating over ion reflection at low ion energies. To understand the impact of ion beam etching on IGZO materials, the chemical composition of IGZO was analyzed using x-ray photoelectron spectroscopy (XPS). An increase in the Ga percentage was observed after etching, accompanied by decreases in the In and Zn percentages, indicating that Ga is the most stable cation in these IGZO films under the ion beam etching etch process. After etching at high incident angles, the chemical composition of the IGZO thin films more closely resembled that of the as-deposited films compared to those processed at low incident angles. The O1s peak in XPS spectra was deconvoluted into three peaks: low binding energy (OL), medium binding energy (OM), and high binding energy (OH), and the ratio of OM to OL was employed to qualitatively assess the concentration of oxygen vacancies in IGZO films. An increase in the OM/OL ratio after the etching process indicates the formation of vacancies.
- 24 March 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (3)
Sputter yield and stoichiometry study of InGaZnO film in ion beam etching
Although extensive research has been conducted on the characteristics of ion beam etching, studies focusing on sputtering yield at low ion energies and the effects of etching on material properties remain limited. In this study, the etching characteristics of InGaZnO4 (IGZO) thin films were investigated using Ar+ ion beams at various ion energies (50–800 eV) and incident angles (0°–87°). At ion energies below 100 eV, the sputter yield continuously increased with the incident angle across the entire range. This phenomenon differs from the established relationship observed at higher ion energies and may be attributed to surface collision dominating over ion reflection at low ion energies. To understand the impact of ion beam etching on IGZO materials, the chemical composition of IGZO was analyzed using x-ray photoelectron spectroscopy (XPS). An increase in the Ga percentage was observed after etching, accompanied by decreases in the In and Zn percentages, indicating that Ga is the most stable cation in these IGZO films under the ion beam etching etch process. After etching at high incident angles, the chemical composition of the IGZO thin films more closely resembled that of the as-deposited films compared to those processed at low incident angles. The O1s peak in XPS spectra was deconvoluted into three peaks: low binding energy (OL), medium binding energy (OM), and high binding energy (OH), and the ratio of OM to OL was employed to qualitatively assess the concentration of oxygen vacancies in IGZO films. An increase in the OM/OL ratio after the etching process indicates the formation of vacancies.
- Open Access
- 19 February 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (3) , 03SP39
Chemical mechanical polishing for indium bond pad damascene processing
We investigated chemical mechanical polishing (CMP) of indium, with the goal of obtaining indium bond pads for later cryo-3D integration of quantum computing-related chips, through bonding between these bond pads and indium bumps. Higher removal rates were obtained with soft CMP pads than with hard pads. The latter led to deep scratching, while this effect was much more limited for soft pad CMP. On patterned wafers, indium is cleared well in structured areas using soft pad CMP, leading to relatively high-quality indium surfaces inside bond pads, although corrosion might be of some concern. Pattern density uniformity was an important factor for within-die deviation in indium clearing time. Dishing was much more limited than in earlier work on indium polishing, while surface roughness was also found to be relatively limited. The obtained indium damascene bond pads may be suitable for 3D die-to-die and wafer-to-wafer bonding through indium pad-to-bump bonding.
- 19 February 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (3) , 03SP39
Open AccessChemical mechanical polishing for indium bond pad damascene processing
We investigated chemical mechanical polishing (CMP) of indium, with the goal of obtaining indium bond pads for later cryo-3D integration of quantum computing-related chips, through bonding between these bond pads and indium bumps. Higher removal rates were obtained with soft CMP pads than with hard pads. The latter led to deep scratching, while this effect was much more limited for soft pad CMP. On patterned wafers, indium is cleared well in structured areas using soft pad CMP, leading to relatively high-quality indium surfaces inside bond pads, although corrosion might be of some concern. Pattern density uniformity was an important factor for within-die deviation in indium clearing time. Dishing was much more limited than in earlier work on indium polishing, while surface roughness was also found to be relatively limited. The obtained indium damascene bond pads may be suitable for 3D die-to-die and wafer-to-wafer bonding through indium pad-to-bump bonding.
- 28 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (12) , 7173-7179
Scaled FinFETs Connected by Using Both Wafer Sides for Routing via Buried Power Rails
We report on scaled finFETs built with a novel routing scheme wherein devices are connected via buried power rails (BPRs) from both wafer sides, with tight variability and matching control. On the wafer’s frontside (FS), M1 lines (FSM1) are connected through V0 vias to M0A lines which are then linked to BPR lines by vias called VBPR while also contacting directly the device’s S/D-epi. As for gate wiring, to enable in this work its access from both wafer sides, gate is also connected to BPR via V0 landing on it and on a neighboring M0A line set only on field-oxide. A single-step metallization for M0A and VBPR is preceded by in situ preclean(s) optimized for improved BPR-VBPR contact interface and $\textit{R}_{\text{ext}}$ , as confirmed electrically and by physical analysis. After FS processing, wafer flipping, bonding, and extreme thinning, highly scaled, $\sim $ 323 nm deep nano-through-Si-vias (nTSVs) land on BPR, with tight overlay control and unchanged BPR resistance 26%–29% lower with improved tungsten (W)-fill, connecting them to the first backside (BS) metal level (BSM1). By moving the power delivery network to the BS (BSPDN), besides alleviating FS routing congestion, considerably smaller dynamic and static IR drop values are predicted from on-chip power heat maps generated for a low power 64-bit CPU at 2-nm design rules: 82% and 96% less worst-case values versus a reference configuration, respectively. P/NMOS show similar or even superior $\textit{I}_{\biosc{on}}$ – $\textit{I}_{\biosc{off}}$ after BS processing and extra anneal(s) added for $\textit{V}_{\textit{T}}$ recovery, mobility and bias temperature instability (BTI) improvement—up to 8%/15% higher $\textit{I}_{\biosc{on}}$ linked to anneal selection.
- 28 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (12) , 7173-7179
Scaled FinFETs Connected by Using Both Wafer Sides for Routing via Buried Power Rails
We report on scaled finFETs built with a novel routing scheme wherein devices are connected via buried power rails (BPRs) from both wafer sides, with tight variability and matching control. On the wafer’s frontside (FS), M1 lines (FSM1) are connected through V0 vias to M0A lines which are then linked to BPR lines by vias called VBPR while also contacting directly the device’s S/D-epi. As for gate wiring, to enable in this work its access from both wafer sides, gate is also connected to BPR via V0 landing on it and on a neighboring M0A line set only on field-oxide. A single-step metallization for M0A and VBPR is preceded by in situ preclean(s) optimized for improved BPR-VBPR contact interface and $\textit{R}_{\text{ext}}$ , as confirmed electrically and by physical analysis. After FS processing, wafer flipping, bonding, and extreme thinning, highly scaled, $\sim $ 323 nm deep nano-through-Si-vias (nTSVs) land on BPR, with tight overlay control and unchanged BPR resistance 26%–29% lower with improved tungsten (W)-fill, connecting them to the first backside (BS) metal level (BSM1). By moving the power delivery network to the BS (BSPDN), besides alleviating FS routing congestion, considerably smaller dynamic and static IR drop values are predicted from on-chip power heat maps generated for a low power 64-bit CPU at 2-nm design rules: 82% and 96% less worst-case values versus a reference configuration, respectively. P/NMOS show similar or even superior $\textit{I}_{\biosc{on}}$ – $\textit{I}_{\biosc{off}}$ after BS processing and extra anneal(s) added for $\textit{V}_{\textit{T}}$ recovery, mobility and bias temperature instability (BTI) improvement—up to 8%/15% higher $\textit{I}_{\biosc{on}}$ linked to anneal selection.
- 1 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Process-induced charging damage in IGZO nTFTs
In this work, charging damage induced by processing in 300mm FAB on Indium-Gallium-Zinc-Oxide (IGZO) n-type Thin Film Transistors (TFT) is investigated using antennae connected at different levels. A compounded degradation due to two different mechanisms is revealed. Plasma etch damage is found to degrade the gate oxide leakage and reliability, while CMP-related charging affects the conductivity of the extension regions of the transistor.
- 1 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Process-induced charging damage in IGZO nTFTs
In this work, charging damage induced by processing in 300mm FAB on Indium-Gallium-Zinc-Oxide (IGZO) n-type Thin Film Transistors (TFT) is investigated using antennae connected at different levels. A compounded degradation due to two different mechanisms is revealed. Plasma etch damage is found to degrade the gate oxide leakage and reliability, while CMP-related charging affects the conductivity of the extension regions of the transistor.
- 16 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (12) , 5349-5354
Buried Power Rail Integration With FinFETs for Ultimate CMOS Scaling
Buried power rail (BPR) is a key scaling booster for CMOS extension beyond the 5-nm node. This work demonstrates, for the first time, the integration of tungsten (W) BPR lines with Si finFETs. BPR technology requires insertion of metal in the front-end-of-line (FEOL) stack. This poses risks of stack deformation and device degradation due to metal-induced stress and contamination. To assess the stack deformation, we demonstrate W-BPR lines which can withstand source/drain activation anneal at 1000 °C, 1.5 s, without adversely impacting the stack morphology. To address the contamination risk, we demonstrate a BPR process module with controlled W recess and void-free dielectric plug formation which keeps the W-line fully encapsulated during downstream FEOL processing. Suitable choice of BPR metal such as W with high melting point which does not diffuse into dielectrics also minimizes the risk of contamination. To assess the device degradation, simulations are carried out showing negligible stress transfer from BPR to the channel. This is experimentally validated when no systematic difference in the dc characteristics of CMOS without BPR versus those in close proximity to floating W-BPR lines is observed. Additionally, the resistance of the recessed W-BPR line is measured $\sim 120~\Omega /\mu \text{m}$ for critical dimension (CD) ~32 nm and height ~122 nm. The recessed W-BPR interface with Ru 3-nm TiN liner via contact can withstand more than 1000 h of electromigration (EM) stress at 6.6 MA/cm 2 and 330 °C, making Ru a candidate for via metallization to achieve low resistance contact strategy to BPR.
- 16 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (12) , 5349-5354
Buried Power Rail Integration With FinFETs for Ultimate CMOS Scaling
Buried power rail (BPR) is a key scaling booster for CMOS extension beyond the 5-nm node. This work demonstrates, for the first time, the integration of tungsten (W) BPR lines with Si finFETs. BPR technology requires insertion of metal in the front-end-of-line (FEOL) stack. This poses risks of stack deformation and device degradation due to metal-induced stress and contamination. To assess the stack deformation, we demonstrate W-BPR lines which can withstand source/drain activation anneal at 1000 °C, 1.5 s, without adversely impacting the stack morphology. To address the contamination risk, we demonstrate a BPR process module with controlled W recess and void-free dielectric plug formation which keeps the W-line fully encapsulated during downstream FEOL processing. Suitable choice of BPR metal such as W with high melting point which does not diffuse into dielectrics also minimizes the risk of contamination. To assess the device degradation, simulations are carried out showing negligible stress transfer from BPR to the channel. This is experimentally validated when no systematic difference in the dc characteristics of CMOS without BPR versus those in close proximity to floating W-BPR lines is observed. Additionally, the resistance of the recessed W-BPR line is measured $\sim 120~\Omega /\mu \text{m}$ for critical dimension (CD) ~32 nm and height ~122 nm. The recessed W-BPR interface with Ru 3-nm TiN liner via contact can withstand more than 1000 h of electromigration (EM) stress at 6.6 MA/cm 2 and 330 °C, making Ru a candidate for via metallization to achieve low resistance contact strategy to BPR.
- 1 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 11.1.1-11.1.4
Vertical Nanowire and Nanosheet FETs: Device Features, Novel Schemes for Improved Process Control and Enhanced Mobility, Potential for Faster & More Energy Efficient Circuits
We report on p and n-type vertical gate-all-around (GAA) nanowire (NW) and nanosheet (NS) FETs which offer attractive opportunities for ultra-scaled circuits. An in-depth evaluation is presented on the impact of doping and key device dimensions to improve the performance, variability, noise and reliability behavior for junctionless (JL) vs. inversion-mode (IM) vertical FETs built with an RMG scheme. The latter enables a novel concept to introduce stress in VFETs for enhanced mobility with up to a19% higher I ON predicted. SiGe/Si pillars and self-aligned spacers offer a solution to gate vertical (mis)alignment towards the S/D. As MRAM selector, VNS FETs can allow substantial area reduction (64% for 2VNS per cell; 3nm node design rules) vs. finFET based cells, with smaller read/write energy consumption and latency times.
- 1 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 11.1.1-11.1.4
Vertical Nanowire and Nanosheet FETs: Device Features, Novel Schemes for Improved Process Control and Enhanced Mobility, Potential for Faster & More Energy Efficient Circuits
We report on p and n-type vertical gate-all-around (GAA) nanowire (NW) and nanosheet (NS) FETs which offer attractive opportunities for ultra-scaled circuits. An in-depth evaluation is presented on the impact of doping and key device dimensions to improve the performance, variability, noise and reliability behavior for junctionless (JL) vs. inversion-mode (IM) vertical FETs built with an RMG scheme. The latter enables a novel concept to introduce stress in VFETs for enhanced mobility with up to a19% higher I ON predicted. SiGe/Si pillars and self-aligned spacers offer a solution to gate vertical (mis)alignment towards the S/D. As MRAM selector, VNS FETs can allow substantial area reduction (64% for 2VNS per cell; 3nm node design rules) vs. finFET based cells, with smaller read/write energy consumption and latency times.