DCDaming Chen

Daming Chen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Daming Chen has a total of 50 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Surface and Interface Engineering of MXenes Enables TCO‐Free Silicon Heterojunction Solar Cells

    by Wei Li, Yu Yan, Taiqiang Wang, Hongyu Dun, Qianfeng Gao, Mingyu Yang, Maobin Zhang, Junming Xue, Daming Chen, Keng Siew Chan, et al.

    Indium tin oxide (ITO) remains the conventional transparent electrode in silicon heterojunction (SHJ) solar cells, yet its reliance on scarce indium raises concerns over cost and scalability. MXenes are solution‐processable and indium‐free, but have so far been confined to electrode roles rather than functioning as primary transparent electrodes that fully displace ITO, particularly on the optically demanding front side. Here we report a fully TCO‐free SHJ solar cell in which surface‐termination engineering enables Ti 3 C 2 T x MXene to act as the transparent electrode on both sides. Hydroxyl‐rich and oxygen‐terminated Ti 3 C 2 T x were synthesized for the front and rear contacts, respectively, with their work functions tuned for the required energy‐level alignment. A front MgF 2 antireflection coating and a rear Ti 3 C 2 T x /AgNW hybrid electrode offset the intrinsic optical losses and inter‐flake resistance of the MXene films. The optimized device reached an efficiency of 23.14%, comparable to a co‐processed, industrially relevant ITO reference. The performance was highly reproducible, with a relative standard deviation in efficiency below 1%, and the devices retained on average over 95% of their initial efficiency after 304 days of storage. These findings establish termination‐engineered MXenes as a credible transparent‐electrode option for next‐generation, indium‐free SHJ photovoltaics.

  • Chemical Composition Evolution and Electrical Performance Degradation of TOPCon Solar Cells Under UV Exposure

    by Xinliang Lou, Ning Yang, Zhiqiang Fu, Daming Chen, Yifeng Chen, Pierre J. Verlinden

    The evolution of the chemical composition and the degradation of the electrical performance of tunnel oxide passivated contact (TOPCon) solar cells under ultraviolet (UV) exposure are analyzed in this paper. Compared to the rear‐side structure (SiO x /n + ‐poly‐Si/Al 2 O 3 /SiN x ) of TOPCon solar cells, the front‐side structure (SiN x /Al 2 O 3 ) exhibits an inferior resistance to UV with a dramatic rise of J 0 . Time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) and depth profiling X‐ray photoelectron spectroscopy (XPS) are used to characterize and to monitor the chemical composition of the front‐side structure during UV60 exposure. The free hydrogen concentration in the passivation layers grows during UV illumination, and the breakage of N–H bonds in SiN x layer is found to be the second source of potential hydrogen loss besides the well‐known Si–H bonds breaking. Meanwhile, Al–O bonds are also found to be dissociated by UV exposure, accompanying the transformation from Al 2 O 3 to Al–OH and the valence states variation of silicon. The free oxygen diffuses into SiN x /Al 2 O 3 interface and Al 2 O 3 /Si interface, with the concentration of oxygen increasing. The XPS spectra also demonstrate that numerous oxygen vacancies form in Al 2 O 3 layer after UV60 illumination, indicating that the film quality is getting damaged. Hydrogen‐related degradation and oxygen‐related degradation have a joint effect on the deterioration of surface recombination, with the relative decline of 3.46% for V oc after UV60 exposure. In addition, the increase of the front contact resistivity contributes to the relative drop of 2.82% for fill factor. Eventually, a dramatic power conversion efficiency degradation of 6.72% is observed for TOPCon solar cells after UV60 illumination.


  • Simulation, Experimental Evaluation, and Characterization of a Novel Grid Line Design for TOPCon Solar Cells With Reduced Silver Consumption

    by Zongtao Liu, Daming Chen, Huili Han, Jianjun Xiang, Zhiyuan Liu, Guanchao Xu, Xueling Zhang, Pierre J. Verlinden, Hui Shen, Yifeng Chen, et al.

    Silver paste accounts for a substantial portion of the nonsilicon cost of tunnel oxide polysilicon contact solar cells. Silver consumption is as well a major concern for material sustainability of global PV manufacturing. It is necessary to propose innovative grid line designs to reduce the amount of silver paste. Partially interrupting the metal fingers (also known as “Finger Break”) between the bus bars in areas where the fingers carry a relatively small current is a good method for reducing silver consumption in industrial production. Under the assumption of uniform generated current density (ISO-current), this article discusses the impact of the width of finger interruption on the cell efficiency under two different scenarios. Through simulations, experiments, and outdoor testing, it was found that one of the considered novel grid designs can save silver paste to a great extent, but suffers a rapid decline in power conversion efficiency, and also poses potential stability risks, while the other grid design not only saves silver, it does not severely affect the efficiency, and can be used outdoors while maintaining stability. Based on the different light intensities, the finger interruption width can be as high as 5 mm, resulting in a saving of 9.32 mg (∼1.61 mg/W) of silver paste on the front surface of 158.75 cm×158.75 cm solar cell, for a reduction of 12.97% of the original front silver consumption.


  • Open Access

    In Situ LID and Regeneration of PERC Solar Cells from Different Positions of a B-Doped Cz-Si Ingot

    by Shuai Yuan, Siqi Ding, Bin Ai, Daming Chen, Jingsheng Jin, Jiaxing Ye, Depeng Qiu, Xiaopu Sun, Xueqin Liang

    In order to investigate the light-induced-degradation (LID) and regeneration of industrial PERC solar cells made from different positions of silicon wafers in a silicon ingot, five groups of silicon wafers were cut from a commercial solar-grade boron-doped Czochralski silicon (Cz-Si) ingot from top to bottom with a certain distance and made into PERC solar cells by using the standard industrial process after measuring lifetimes of minority carriers and concentrations of boron, oxygen, carbon, and transition metal impurities. Then, the changes of their - characteristic parameters (efficiency , open-circuit voltage , short-circuit current , and fill factor ) with time were in situ measured by using a solar cell - tester during the 1st LID (45°C, 1 sun, 12 h), regeneration (100°C, 1 sun, 24 h), and 2nd LID (45°C, 1 sun, 12 h). The results show that the LID and regeneration of the PERC solar cells are caused by the transition of B-O defects playing a dominant role together with the dissociation of Fe-B pairs playing a secondary role. The decay of during the 1st LID is caused by the degradation of , , and , while the increase of during the regeneration is mainly contributed by and , and the decay of during the 2nd LID is mainly induced by the degradation of . After regeneration, the decay rate of reduces from 4.43%–5.56% (relative) during the 1st LID to 0.33%–1.75% (relative) during the 2nd LID.


  • Mass production of industrial tunnel oxide passivated contacts (i‐TOPCon) silicon solar cells with average efficiency over 23% and modules over 345 W

    by Yifeng Chen, Daming Chen, Chengfa Liu, Zigang Wang, Yang Zou, Yu He, Yao Wang, Ling Yuan, Jian Gong, Wenjie Lin, et al.

    We present an industrial tunnel oxide passivated contacts (i‐TOPCon) bifacial crystalline silicon (c‐Si) solar cell based on large‐area n‐type substrate. The interfacial thin SiO2 is thermally growth and in situ capped by an intrinsic poly‐Si layer deposited by low‐pressure chemical vapor deposition (LPCVD). The intrinsic poly‐Si layer is doped in an industrial POCl3 diffusion furnace to form the n+ poly‐Si at the rear, which shows an excellent surface passivation characteristics with J0 = 2.6 fA/cm2 when passivated by a SiNx:H layer deposited by plasma‐enhanced chemical vapor deposition (PECVD). With an industrial fabrication process, the cells are manufactured with screen‐printed front and rear metallization, using large‐area 6‐in. n‐type Czochralski (Cz) Si wafers. We demonstrate an average front‐side efficiency greater than 23% and an open‐circuit voltage Voc greater than 700 mV. These results are based on more than 20 000 pieces of cells from mass production on a single day, in an old conventional multicrystalline silicon (mc‐Si) Al‐back surface field (BSF) cell workshop, which has been upgraded to i‐TOPCon process. The best cell efficiency reaches 23.57%, as independently confirmed by Fraunhofer CalLab. A median module power greater than 345 W and a best module power greater than 355 W are demonstrated with double‐glass bifacial i‐TOPCon modules consisting of 120 pieces of half‐cut 161.7 mm pseudosquare i‐TOPCon cells with nine busbars.


  • A method for optimizing PERC cells in industrial production lines using final IV parameters, statistical procedures and numerical device modeling

    by Pietro P. Altermatt, Yang Yang, Yun Sheng, Daming Chen, Yifeng Chen, Zhiqiang Feng, Pierre J. Verlinden

    PERC Si solar cells have many processing parameters that interact with each other in a complex manner. Hence, efficiency changes can often not be allocated to a single fabrication tool. This makes the mass fabrication of PERC cells difficult to optimize and improve. On top of this, the wafers usually go through batch processes with parallel equipment, and are not traced. Thus, we developed an optimization method that uses solely the final IV parameters, treats these data statistically, and combines them with device modeling to identify sets of fabrication tools that most likely cause suboptimum cell efficiencies, and we identify specific reasons for the best cells, so the baseline efficiency can be increased. Concretely, an automatic algorithm identifies which departures from the median cell efficiency are statistically significant. These departures are caused by changes of different sets of IV parameters. The different sets are classified with a clustering algorithm, and each cluster is traced back to deviations in a group of fabrication tools by means of numerical device modeling tailored to the situation. We applied this method in a 2-week period to 552’000 cells in a line being ramped-up. We found 10 clusters (i.e. different ways of departures from median efficiency), which are then exploited to improve PERC cell efficiency more swiftly.