Balasingam Muhunthan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Balasingam Muhunthan has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Kun Zhang
Department of Civil Engineering, California State University, Chico, USA
4 shared publications - Kalehiwot Nega Manahiloh
Civil Engineering Department, Liberty University, Lynchburg, VA 24515, USA
3 shared publications - Tae-Hyuk Kwon
Korea Advanced Institute of Science and Technology
3 shared publications H. M. Zbib
Department of Civil and Environmental Engineering, Washington State University, Pullman, WA, U.S.A.
2 shared publications- Haifang Wen
Washington State Univ
2 shared publications - Jagan M. Padbidri
School of Mechanical and Materials Engineering, Washington State University, Pullman, WA, USA
2 shared publications
Latest Publications
- 19 September 2022
- Published by Morressier GmbH
Sustainable Patching Material Using 100% RAP and Biobinder from Waste Cooking Oil
This study developed a new sustainable pothole patching material using 100% reclaimed asphalt pavement (RAP) and a biobinder from waste cooking o |
- 19 September 2022
- Published by Morressier GmbH
Sustainable Patching Material Using 100% RAP and Biobinder from Waste Cooking Oil
This study developed a new sustainable pothole patching material using 100% reclaimed asphalt pavement (RAP) and a biobinder from waste cooking o |
- 17 January 2022
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 40  (4) , 2339-2355
Analysis of Time-Dependent Soil Behavior Above High-Filled Cut-and-Cover Tunnels Using Discrete Element Method
- 17 January 2022
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 40  (4) , 2339-2355
Analysis of Time-Dependent Soil Behavior Above High-Filled Cut-and-Cover Tunnels Using Discrete Element Method
- 28 May 2021
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 144  (1) , 1-34
Evolution of Strain Gradient Formulation in Capturing Localization Phenomena in Granular Materials
This paper highlights the use of incorporating strain gradient into flow stress to study localization behavior in materials. Pioneered by Zbib and Aifantis in the late 1980s, the formulation enabled incorporation of length scales into continuum formulations naturally. The formulation has also evolved into being able to study the effects of microstructure and heterogeneity on localization in granular materials. A multi-slip Mohr–Coulomb type plasticity model with the flow stress in the constitutive equation modified with a higher order gradient term of the effective plastic strain is used for this purpose. The possibility of abrupt changes of mobilized friction caused by intense shearing rate often leads to particle breakage. Its effects on localization are accounted for by modifying the material properties such as mobilized friction using a scaling parameter averaged over a representative elementary area. The change of shearing rate in the integration points was monitored through quasi-statistically measure parameter called inertia number. The inertia number was set to be less than l.0 × 10−3 all the time to consider quasi-static. The formulation was implemented into a finite element code and used to simulate plane strain compression tests on dry sand. The model highlights the effects of confining pressure, anisotropic microstructure, and the non-coaxial angle between the direction of principal stress and principal plastic strain rate directions on shear band characteristics.
- 28 May 2021
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 144  (1) , 1-34
Evolution of Strain Gradient Formulation in Capturing Localization Phenomena in Granular Materials
This paper highlights the use of incorporating strain gradient into flow stress to study localization behavior in materials. Pioneered by Zbib and Aifantis in the late 1980s, the formulation enabled incorporation of length scales into continuum formulations naturally. The formulation has also evolved into being able to study the effects of microstructure and heterogeneity on localization in granular materials. A multi-slip Mohr–Coulomb type plasticity model with the flow stress in the constitutive equation modified with a higher order gradient term of the effective plastic strain is used for this purpose. The possibility of abrupt changes of mobilized friction caused by intense shearing rate often leads to particle breakage. Its effects on localization are accounted for by modifying the material properties such as mobilized friction using a scaling parameter averaged over a representative elementary area. The change of shearing rate in the integration points was monitored through quasi-statistically measure parameter called inertia number. The inertia number was set to be less than l.0 × 10−3 all the time to consider quasi-static. The formulation was implemented into a finite element code and used to simulate plane strain compression tests on dry sand. The model highlights the effects of confining pressure, anisotropic microstructure, and the non-coaxial angle between the direction of principal stress and principal plastic strain rate directions on shear band characteristics.
- 1 September 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering, Part B: Pavements
- Vol. 146  (3) , 04020050
Evaluating Cost Effectiveness and Optimal Timing of Pavement Preventive-Maintenance Treatments in Wet-Freeze Climates
Preventive-maintenance treatments help preserve pavements and delay deterioration caused by traffic loads and environmental conditions. However, guidance is needed to ensure cost effectiveness of treatments, the benefit-to-cost ratio of different treatments applied based on time. In this study, the cost effectiveness of the thin overlay, slurry seal, crack seal, and chip seal methods applied at different times were evaluated using the regression model of performance curves from Long-Term Pavement Performance (LTPP) data. The cost effectiveness is found to depend on the type of treatment and the time of applications as well as the chosen benefit cutoff value. The benefit cutoff value is a predefined performance threshold limit of cracking, above which the pavement is not acceptable for use. For average climate, traffic, and pavement conditions, the highest cost effectiveness corresponding to treatment ages of 1, 4, 7, 10, 13, and 16 years were found to be at benefit cutoff values of 150, 150, 200, 250, 300, and 300 m, respectively. When treatment is applied at 1, 4, or 7 years, crack seal is found to give the maximum cost effectiveness, and if treatment is applied at 10, 13, or 16 years, chip seal is found to give the maximum cost effectiveness. Comparison of all the benefit-to-cost ratios shows that the overall highest cost effectiveness is obtained when chip seal is applied at 16 years with a 300-m benefit cutoff value. When the annual average freeze index is 34°C days, crack seal gives the maximum cost effectiveness if treatment is applied at 1, 4, 7, 10, or 13 years. On the contrary, if treatment is applied at 16 years, slurry seal is found to give maximum cost effectiveness. When annual average freeze index is 1,699°C days and annual average daily traffic is 450, chip seal gives the maximum cost effectiveness irrespective of treatment ages. When annual average daily traffic is 7,933 at all treatment ages, crack seal gives the maximum cost effectiveness.
- 1 September 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering, Part B: Pavements
- Vol. 146  (3) , 04020050
Evaluating Cost Effectiveness and Optimal Timing of Pavement Preventive-Maintenance Treatments in Wet-Freeze Climates
Preventive-maintenance treatments help preserve pavements and delay deterioration caused by traffic loads and environmental conditions. However, guidance is needed to ensure cost effectiveness of treatments, the benefit-to-cost ratio of different treatments applied based on time. In this study, the cost effectiveness of the thin overlay, slurry seal, crack seal, and chip seal methods applied at different times were evaluated using the regression model of performance curves from Long-Term Pavement Performance (LTPP) data. The cost effectiveness is found to depend on the type of treatment and the time of applications as well as the chosen benefit cutoff value. The benefit cutoff value is a predefined performance threshold limit of cracking, above which the pavement is not acceptable for use. For average climate, traffic, and pavement conditions, the highest cost effectiveness corresponding to treatment ages of 1, 4, 7, 10, 13, and 16 years were found to be at benefit cutoff values of 150, 150, 200, 250, 300, and 300 m, respectively. When treatment is applied at 1, 4, or 7 years, crack seal is found to give the maximum cost effectiveness, and if treatment is applied at 10, 13, or 16 years, chip seal is found to give the maximum cost effectiveness. Comparison of all the benefit-to-cost ratios shows that the overall highest cost effectiveness is obtained when chip seal is applied at 16 years with a 300-m benefit cutoff value. When the annual average freeze index is 34°C days, crack seal gives the maximum cost effectiveness if treatment is applied at 1, 4, 7, 10, or 13 years. On the contrary, if treatment is applied at 16 years, slurry seal is found to give maximum cost effectiveness. When annual average freeze index is 1,699°C days and annual average daily traffic is 450, chip seal gives the maximum cost effectiveness irrespective of treatment ages. When annual average daily traffic is 7,933 at all treatment ages, crack seal gives the maximum cost effectiveness.
- 1 February 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 31  (2)
Development of Dynamic Modulus–Based Mixture Blending Chart for Asphalt Mixtures with Reclaimed Asphalt Pavement
The current practice of using the binder blending chart to select a performance grade of the virgin binder may not be applicable for mixtures containing more than 25% reclaimed asphalt pavement (RAP), since the binder blending chart assumes full blending between virgin and RAP binders. For such high RAP percentage cases, a blending chart based directly on the performance of mixtures would be a better choice. This study develops a mixture blending chart based on the dynamic modulus values of RAP mixtures to better control their performance. Three rules of mixtures were considered to develop the mixture blending chart, including Voigt rule, Reuss rule, and a joint Voigt and Reuss (V&R) rule. The dynamic modulus values of three sets of RAP mixtures were measured in this study. The results indicated that the dynamic modulus values calculated by the joint V&R rule matched the measured values of the corresponding RAP mixtures better than those calculated by the Reuss rule and Voigt rule. Digital images of two-dimensional slices of the laboratory specimens were taken and used to construct the ideal binary-blended RAP mixtures, and the finite-element analyses were conducted to determine the modulus values of these digital RAP mixtures to verify the developed mixture blending chart. The modulus results of digital RAP mixtures matched the modulus values determined based on the joint V&R rule. We conclude that the joint V&R rule could be used as the mixture blending chart to select an appropriate virgin binder when designing high RAP content mixtures.
- 1 February 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 31  (2)
Development of Dynamic Modulus–Based Mixture Blending Chart for Asphalt Mixtures with Reclaimed Asphalt Pavement
The current practice of using the binder blending chart to select a performance grade of the virgin binder may not be applicable for mixtures containing more than 25% reclaimed asphalt pavement (RAP), since the binder blending chart assumes full blending between virgin and RAP binders. For such high RAP percentage cases, a blending chart based directly on the performance of mixtures would be a better choice. This study develops a mixture blending chart based on the dynamic modulus values of RAP mixtures to better control their performance. Three rules of mixtures were considered to develop the mixture blending chart, including Voigt rule, Reuss rule, and a joint Voigt and Reuss (V&R) rule. The dynamic modulus values of three sets of RAP mixtures were measured in this study. The results indicated that the dynamic modulus values calculated by the joint V&R rule matched the measured values of the corresponding RAP mixtures better than those calculated by the Reuss rule and Voigt rule. Digital images of two-dimensional slices of the laboratory specimens were taken and used to construct the ideal binary-blended RAP mixtures, and the finite-element analyses were conducted to determine the modulus values of these digital RAP mixtures to verify the developed mixture blending chart. The modulus results of digital RAP mixtures matched the modulus values determined based on the joint V&R rule. We conclude that the joint V&R rule could be used as the mixture blending chart to select an appropriate virgin binder when designing high RAP content mixtures.
- 16 August 2018
- Published by ASTM International in Geotechnical Testing Journal
- Vol. 42  (1) , 101-116
Test Method Evaluation and Model Development for Erodibility Properties of Cementitiously Stabilized Layers
Cementitiously stabilized layers (CSL) have been used extensively by highway agencies over the years. The erosion of CSL can cause several distresses in flexible and rigid pavements. The three necessary conditions for the occurrence of erosion are heavy loads, sufficient moisture, and the presence of erodible materials. The Mechanistic-Empirical Pavement Design Guide (MEPDG) provides a methodology for the analysis and performance prediction of pavements that incorporate CSL. However, test methods and models that specifically address the erosion of CSL have not yet been incorporated into the MEPDG. This study evaluates the existing test methods for erosion, including wheel tracking, manual wet-dry brushing, rotational shear device (RSD), jetting, a vibration table, or cyclic impact erosion (CIE), or combinations thereof. It is found that a CIE test is a robust test procedure that is used to quantify the erodibility of CSL. Based on the laboratory results from a CIE test, an empirical model that combines top-down compressive fatigue and erosion is developed to predict the erodibility of CSL. It is found that the developed model is effective in predicting both the top-down compressive fatigue and erosion of CSL. This test method and prediction model are recommended for incorporation into the MEPDG.
- 16 August 2018
- Published by ASTM International in Geotechnical Testing Journal
- Vol. 42  (1) , 101-116
Test Method Evaluation and Model Development for Erodibility Properties of Cementitiously Stabilized Layers
Cementitiously stabilized layers (CSL) have been used extensively by highway agencies over the years. The erosion of CSL can cause several distresses in flexible and rigid pavements. The three necessary conditions for the occurrence of erosion are heavy loads, sufficient moisture, and the presence of erodible materials. The Mechanistic-Empirical Pavement Design Guide (MEPDG) provides a methodology for the analysis and performance prediction of pavements that incorporate CSL. However, test methods and models that specifically address the erosion of CSL have not yet been incorporated into the MEPDG. This study evaluates the existing test methods for erosion, including wheel tracking, manual wet-dry brushing, rotational shear device (RSD), jetting, a vibration table, or cyclic impact erosion (CIE), or combinations thereof. It is found that a CIE test is a robust test procedure that is used to quantify the erodibility of CSL. Based on the laboratory results from a CIE test, an empirical model that combines top-down compressive fatigue and erosion is developed to predict the erodibility of CSL. It is found that the developed model is effective in predicting both the top-down compressive fatigue and erosion of CSL. This test method and prediction model are recommended for incorporation into the MEPDG.
- 1 July 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 30  (7)
Comparison of Laboratory and Field Asphalt Aging for Polymer-Modified and Warm-Mix Asphalt Binders
The laboratory aging tests for binders were developed based on Strategic Highway Research Program (SHRP) tests in the 1990s (i.e., performance grading); the applicability of performance grade (PG) to recently developed tests, such as multiple stress creep recovery (MSCR), is not clear. In addition, the ability of laboratory aging to represent field pavement aging, especially when polymer-modified asphalt (PMA) and warm-mix asphalt (WMA) binders are used, has been a concern to paving practice. This paper investigates quantitatively the level of laboratory aging compared to the field aging for both the control hot-mix asphalt (HMA) binders and WMA and PMA binders. The study focuses on a number of binder parameters, as well as evaluating whether the current laboratory aging conditions (loose-mix oven aging) will provide correlation to field short-term aging. HMA and WMA binders from four field projects that covered different climatic zones, pavement structures, and materials were selected. Binder properties including high-temperature PG, MSCR nonrecoverable creep compliance, low-temperature binder PG, and fracture energy were used for analysis. The results show that the laboratory rolling thin-film oven (RTFO) aging method is not sufficient to simulate field short-term aging conditions for most cases except for the low-temperature PG test. The aging of asphalt binder is parameter sensitive; depending on the parameters used, the comparison results between laboratory aging and field aging could be different. The effect of aging on PMA binder, especially when mixed with Sasobit additive, differs from non-polymer-modified binders. Limited results from non-polymer-modified binder mixes suggested that loose-mix oven aging at 85°C for 2, 5, and 7 days appears to provide a reasonable simulation of field pavement aging right after compaction (0 years), 1.8 years, and 3 years.
- 1 July 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 30  (7)
Comparison of Laboratory and Field Asphalt Aging for Polymer-Modified and Warm-Mix Asphalt Binders
The laboratory aging tests for binders were developed based on Strategic Highway Research Program (SHRP) tests in the 1990s (i.e., performance grading); the applicability of performance grade (PG) to recently developed tests, such as multiple stress creep recovery (MSCR), is not clear. In addition, the ability of laboratory aging to represent field pavement aging, especially when polymer-modified asphalt (PMA) and warm-mix asphalt (WMA) binders are used, has been a concern to paving practice. This paper investigates quantitatively the level of laboratory aging compared to the field aging for both the control hot-mix asphalt (HMA) binders and WMA and PMA binders. The study focuses on a number of binder parameters, as well as evaluating whether the current laboratory aging conditions (loose-mix oven aging) will provide correlation to field short-term aging. HMA and WMA binders from four field projects that covered different climatic zones, pavement structures, and materials were selected. Binder properties including high-temperature PG, MSCR nonrecoverable creep compliance, low-temperature binder PG, and fracture energy were used for analysis. The results show that the laboratory rolling thin-film oven (RTFO) aging method is not sufficient to simulate field short-term aging conditions for most cases except for the low-temperature PG test. The aging of asphalt binder is parameter sensitive; depending on the parameters used, the comparison results between laboratory aging and field aging could be different. The effect of aging on PMA binder, especially when mixed with Sasobit additive, differs from non-polymer-modified binders. Limited results from non-polymer-modified binder mixes suggested that loose-mix oven aging at 85°C for 2, 5, and 7 days appears to provide a reasonable simulation of field pavement aging right after compaction (0 years), 1.8 years, and 3 years.
- Open Access
- 1 July 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 144  (7)
Improvement of Surface Erosion Resistance of Sand by Microbial Biopolymer Formation
Direct use of naturally occurring microbes for soil improvement has recently gained attention due to their ubiquitous and versatile characteristics in subsurface soil. Microbes produce soft and sticky extracellular polymeric substances (or biopolymers) that are known to alter the hydrological characteristics of soils; however, the mechanisms and extent of such soft biopolymers in altering soil erosion resistance remain scarcely explored. This study explored the role of microbial biopolymers in soil erosion resistance. The surface erosion resistance of sandy soils was evaluated by using a hybrid erosion function apparatus, in which the model bacteria Leuconostoc mesenteroides were stimulated to produce an insoluble biopolymer. The results revealed that the microbial biopolymer formation increased the critical shear stress and surface erosion resistance, which the researchers attributed to the increased cohesion by grain-coating biopolymer slimes and the reduced seepage flows due to pore clogging. This study provides baseline but promising results on how microbially grown biopolymers can be used to improve soil erosion resistance.
- 1 July 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 144  (7)
Open AccessImprovement of Surface Erosion Resistance of Sand by Microbial Biopolymer Formation
Direct use of naturally occurring microbes for soil improvement has recently gained attention due to their ubiquitous and versatile characteristics in subsurface soil. Microbes produce soft and sticky extracellular polymeric substances (or biopolymers) that are known to alter the hydrological characteristics of soils; however, the mechanisms and extent of such soft biopolymers in altering soil erosion resistance remain scarcely explored. This study explored the role of microbial biopolymers in soil erosion resistance. The surface erosion resistance of sandy soils was evaluated by using a hybrid erosion function apparatus, in which the model bacteria Leuconostoc mesenteroides were stimulated to produce an insoluble biopolymer. The results revealed that the microbial biopolymer formation increased the critical shear stress and surface erosion resistance, which the researchers attributed to the increased cohesion by grain-coating biopolymer slimes and the reduced seepage flows due to pore clogging. This study provides baseline but promising results on how microbially grown biopolymers can be used to improve soil erosion resistance.
- 1 April 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 144  (4)
Modeling of Permeability Reduction in Bioclogged Porous Sediments
This study examines the use of a numerical model to predict the reduction in permeability of bioclogged specimens observed from column experiments. The numerical model uses the two-dimensional (2D) segmented scanning electron microscope (SEM) images of the initial microstructure of soil and simulates the growth of biofilm assuming uniform grain coating around particles. The corresponding Navier-Stokes equation in free pore space and the flow within the biofilm described by the Brinkman equations are solved using finite-element analysis. The numerical results are shown to match the experimental data very well. The predictions by the different analytical models used in the current literature are also compared. The numerical model, utilizing the uniform grain coating criterion for biofilm growth, is shown to predict well the permeability reduction of porous medium as a function of biofilm saturation.
- 1 April 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 144  (4)
Modeling of Permeability Reduction in Bioclogged Porous Sediments
This study examines the use of a numerical model to predict the reduction in permeability of bioclogged specimens observed from column experiments. The numerical model uses the two-dimensional (2D) segmented scanning electron microscope (SEM) images of the initial microstructure of soil and simulates the growth of biofilm assuming uniform grain coating around particles. The corresponding Navier-Stokes equation in free pore space and the flow within the biofilm described by the Brinkman equations are solved using finite-element analysis. The numerical results are shown to match the experimental data very well. The predictions by the different analytical models used in the current literature are also compared. The numerical model, utilizing the uniform grain coating criterion for biofilm growth, is shown to predict well the permeability reduction of porous medium as a function of biofilm saturation.
- 1 March 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 30  (3)
Evaluation of the Effects of Waste Engine Oil on the Rheological Properties of Asphalt Binders
This study evaluated the feasibility of using waste engine oil (WEO) to partially replace virgin asphalt binder. Two base asphalt binders (PG 64-28 and PG 76-22) were blended with three different WEO percentages of 0, 5, and 10%, respectively. First, the effects of WEO on two base asphalt binders were evaluated by the mass loss during rolling thin film oven (RTFO) and by performance grading (PG) test. Second, based on the developed WEO-PG formula, two binders were designed to have equivalent low temperature PG. Subsequently, the rheological properties of these two low-PG-equivalent binders were evaluated by PG, multiple stress creep recovery (MSCR), frequency sweep, and monotonic fracture tests. Results of the study showed that use of higher WEO content resulted in a decreased PG for base asphalt binder, but the amount of decrease was dependent on the base asphalt type. With the presence of WEO, the binders having equivalent low-temperature PG did not necessarily exhibit similar stiffness or fracture property. WEO had a softening effect, and an improved elasticity and recovery property on the base asphalt.
- 1 March 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 30  (3)
Evaluation of the Effects of Waste Engine Oil on the Rheological Properties of Asphalt Binders
This study evaluated the feasibility of using waste engine oil (WEO) to partially replace virgin asphalt binder. Two base asphalt binders (PG 64-28 and PG 76-22) were blended with three different WEO percentages of 0, 5, and 10%, respectively. First, the effects of WEO on two base asphalt binders were evaluated by the mass loss during rolling thin film oven (RTFO) and by performance grading (PG) test. Second, based on the developed WEO-PG formula, two binders were designed to have equivalent low temperature PG. Subsequently, the rheological properties of these two low-PG-equivalent binders were evaluated by PG, multiple stress creep recovery (MSCR), frequency sweep, and monotonic fracture tests. Results of the study showed that use of higher WEO content resulted in a decreased PG for base asphalt binder, but the amount of decrease was dependent on the base asphalt type. With the presence of WEO, the binders having equivalent low-temperature PG did not necessarily exhibit similar stiffness or fracture property. WEO had a softening effect, and an improved elasticity and recovery property on the base asphalt.