Benedikt Janßen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Benedikt Janßen has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Florian Kästner
Ruhr-University Bochum
1 shared publicationMichael Hubner
1 shared publicationMichael Huebner
Ruhr-University Bochum
1 shared publicationMoataz Naserddin
1 shared publication- Patrick Hermanns
Electrical Engineering and Plasma Technology, Ruhr University Bochum, Ruhr-Universitaet, Gebauede ID, ID 1/537, Bochum, NRW, 44801, GERMANY
1 shared publication - Stephan Westerdick
Institute of Electronic Circuits, Ruhr University Bochum, 44801 Bochum, Germany
1 shared publication
Latest Publications
- Open Access
- 30 November 2018
- Published by MDPI AG in Proceedings
- Vol. 2 (13) , 1071
Exchangeable Miniaturized Mass Spectrometer Chip Based on Silicon Structures
This paper reports a design of an exchangeable miniaturized mass spectrometry chip using spring-loaded pins and O-rings for electrical and fluidic connections. This planar microelectromechanical system (MEMS)-chip works with 300 µm high silicon structures between two borosilicate glasses and has a size of 13 mm × 7 mm. Because of its small size a small vacuum pump is sufficient, and it is suitable for mobile measurements and portable applications. Because of exchangeability of MEMS-chips with fluidic and electrical high voltage connections a direct comparison between chips is possible.
- 30 November 2018
- Published by MDPI AG in Proceedings
- Vol. 2 (13) , 1071
Open AccessExchangeable Miniaturized Mass Spectrometer Chip Based on Silicon Structures
This paper reports a design of an exchangeable miniaturized mass spectrometry chip using spring-loaded pins and O-rings for electrical and fluidic connections. This planar microelectromechanical system (MEMS)-chip works with 300 µm high silicon structures between two borosilicate glasses and has a size of 13 mm × 7 mm. Because of its small size a small vacuum pump is sufficient, and it is suitable for mobile measurements and portable applications. Because of exchangeability of MEMS-chips with fluidic and electrical high voltage connections a direct comparison between chips is possible.
- 8 April 2018
- Published by Springer Nature
- p. 331-342
A Dynamic Partial Reconfigurable Overlay Framework for Python
- 8 April 2018
- Published by Springer Nature
- p. 331-342
A Dynamic Partial Reconfigurable Overlay Framework for Python
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 241-246
A Hardware/Software Co-Design Approach for Control Applications with Static Real-Time Reallocation
The reliability of a system can be increased by redundancy. With redundancy, faults can be detected through comparison and failing components can be replaced. In order to avoid the verification of different implementations, the creation of redundant components from a single source is beneficial. In this paper, we propose a hardware/software (hw/sw) co-design approach for control applications that target a hardware platform based on the Xilinx Zynq-7000. Our approach contains a tool chain that allows to generate the software task, as well as a hardware accelerator from the same controller model. Moreover, it includes an architecture which allows to switch between the two implementations while maintaining soft real-time constraints. The hardware accelerator can be instantiated multiple times and the software task can be started on multiple processor cores in order to increase the redundancy. We evaluated our approach with a closed-loop controller in a process automation scenario, in which the water of a tank is kept at a constant level. We show, that redundancy can be added with only little effort during development time as well as runtime, and that the control mechanism is not influenced by dynamic reallocation.
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 241-246
A Hardware/Software Co-Design Approach for Control Applications with Static Real-Time Reallocation
The reliability of a system can be increased by redundancy. With redundancy, faults can be detected through comparison and failing components can be replaced. In order to avoid the verification of different implementations, the creation of redundant components from a single source is beneficial. In this paper, we propose a hardware/software (hw/sw) co-design approach for control applications that target a hardware platform based on the Xilinx Zynq-7000. Our approach contains a tool chain that allows to generate the software task, as well as a hardware accelerator from the same controller model. Moreover, it includes an architecture which allows to switch between the two implementations while maintaining soft real-time constraints. The hardware accelerator can be instantiated multiple times and the software task can be started on multiple processor cores in order to increase the redundancy. We evaluated our approach with a closed-loop controller in a process automation scenario, in which the water of a tank is kept at a constant level. We show, that redundancy can be added with only little effort during development time as well as runtime, and that the control mechanism is not influenced by dynamic reallocation.