Peter Burik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Peter Burik has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- M Mojžiš
ŽP Research and Development Centre, Kolkáreň 35, 976 81 Podbrezová, Slovak Republic, EU
1 shared publication - Matúš Turis
Department of Structural Mechanics, Faculty of Civil Engineering, Slovak University of Technology, Radlinského 11, 810 05 Bratislava, Slovakia
1 shared publication - Milan Držík
International Laser Center, Ilkovičova 2961/3, 841 04 Bratislava, Slovakia
1 shared publication - Oľga Ivánková
Department of Structural Mechanics, Faculty of Civil Engineering, Slovak University of Technology in Bratislava, Radlinskeho 11, SK-810 05 Bratislava, Slovakia
1 shared publication - Pavel Kejzlar
Technical University of Liberec
1 shared publication - Peter Bella
ŽP Research and Development Centre
1 shared publication
Latest Publications
- Open Access
- 17 May 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (10) , 4574
Determination of Stress Intensity Factors under Shock Loading Using a Diffraction-Based Technique
An experimental optical method has been developed for the measurement of opening and sliding notch face movements. The light passing through a thin slit is monitored by a photodiode detector. Two parts of the slit are fixed independently on the notch faces of the simulated crack. Dynamic variations of the notch face movements are recorded as an electric signal by an oscilloscope. The sensitivity of such displacement measurement is comparable with the wavelength of light. Dynamic mixed-mode stress intensity factors under shock loading were evaluated from the data obtained and subsequently compared with a numerical simulation by ANSYS software. As it was approved, the technique has shown sufficient sensitivity, good linearity, and measurement reliability. Due to its non-destructive nature and overall robustness, the arrangement is applicable even for structural component condition determination taking into consideration potentially unknown boundary conditions and the non-linear character of mechanical parameters.
- 17 May 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (10) , 4574
Open AccessDetermination of Stress Intensity Factors under Shock Loading Using a Diffraction-Based Technique
An experimental optical method has been developed for the measurement of opening and sliding notch face movements. The light passing through a thin slit is monitored by a photodiode detector. Two parts of the slit are fixed independently on the notch faces of the simulated crack. Dynamic variations of the notch face movements are recorded as an electric signal by an oscilloscope. The sensitivity of such displacement measurement is comparable with the wavelength of light. Dynamic mixed-mode stress intensity factors under shock loading were evaluated from the data obtained and subsequently compared with a numerical simulation by ANSYS software. As it was approved, the technique has shown sufficient sensitivity, good linearity, and measurement reliability. Due to its non-destructive nature and overall robustness, the arrangement is applicable even for structural component condition determination taking into consideration potentially unknown boundary conditions and the non-linear character of mechanical parameters.
- Open Access
- 10 December 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 461 (1) , 012010
Evolution of deformation texture in cold drawing of steel tubes using EBSD analysis and FEM simulation
Cold drawing of steel tubes is the manufacturing process characterized by anisotropic material flow during drawing. In this paper, the micro structural of the E235 steel tube after recrystallization annealing and cold drawing were characterized by optical microscopy and EBSD (Electron BackScatter Diffraction) analysis performed on a scanning electron microscope. The input feedstock after recrystallization annealing with dimensions of ø 25.0 mm × 1.5 mm (O.D × W.T.) was cold drawn in two drawing passes with fixed plug to the final dimensions of ø 18.0 mm × 0.9 mm (O.D × W.T.). The development of crystallographic texture (both qualitative and quantitative) was analysed on a longitudinal section of the tube. The stress-strain state in the tube material during drawing was calculated by FEM (Final Element Method) software and the development of the texture depending on the stress-strain state in three different directions using cylindrical coordinates with respect to the drawing direction was evaluated. We have investigated the ratio of individual crystallographic planes depending on stress state during drawn tube. The main objective was to define the development of crystallographic grain orientation from stress-strain state during cold drawn tube.
- 10 December 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 461 (1) , 012010
Open AccessEvolution of deformation texture in cold drawing of steel tubes using EBSD analysis and FEM simulation
Cold drawing of steel tubes is the manufacturing process characterized by anisotropic material flow during drawing. In this paper, the micro structural of the E235 steel tube after recrystallization annealing and cold drawing were characterized by optical microscopy and EBSD (Electron BackScatter Diffraction) analysis performed on a scanning electron microscope. The input feedstock after recrystallization annealing with dimensions of ø 25.0 mm × 1.5 mm (O.D × W.T.) was cold drawn in two drawing passes with fixed plug to the final dimensions of ø 18.0 mm × 0.9 mm (O.D × W.T.). The development of crystallographic texture (both qualitative and quantitative) was analysed on a longitudinal section of the tube. The stress-strain state in the tube material during drawing was calculated by FEM (Final Element Method) software and the development of the texture depending on the stress-strain state in three different directions using cylindrical coordinates with respect to the drawing direction was evaluated. We have investigated the ratio of individual crystallographic planes depending on stress state during drawn tube. The main objective was to define the development of crystallographic grain orientation from stress-strain state during cold drawn tube.