Barisoa Harijaona Rafidison
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Barisoa Harijaona Rafidison has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- François Benjamin Vincent Florens
Tropical Island Biodiversity, Ecology and Conservation Pole of Research, Department of Biosciences and Ocean Studies, Faculty of Science, University of Mauritius, Le Réduit, Mauritius
4 shared publications - Hareenanden Ramasawmy
University of Mauritius
4 shared publications Jaykumar Chummun
University of Mauritius
4 shared publications
Latest Publications
- 9 February 2026
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 45 (21-22) , 4954-4968
Development of an effective non-woven fibre mat via wet-laid process for structural composite reinforcement applications
The use of structural composite materials demands high homogeneity to ensure efficient load transfer. A wet-laid web process, incorporating 2% by weight of hydroxyethylcellulose (HEC) as a bonding agent, was employed to fabricate non-woven mats, using randomly distributed fibres of a native Mauritius Screwpine ( Pandanus utilis ). Morphological analysis revealed that the resulting mats exhibited superior homogeneity compared to commercial E-glass mats. Three polyester composites were fabricated with fibre mat contents of 10.7%, 21.4%, and 32.1% (corresponding to one, two, and three layers, respectively). The composite with the highest tensile and flexural strengths was selected for manufacturing a 550 mm wind turbine blade (WTB). A flap-wise static test, conducted in accordance with BS EN 61400-2, confirmed that the blade could withstand worst-case loading with a 39% safety margin before failure. The results demonstrate the composite’s suitability for structural applications, with the non-woven mat’s flexibility enabling easy adaptation to complex mould geometries.
- 9 February 2026
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 45 (21-22) , 4954-4968
Development of an effective non-woven fibre mat via wet-laid process for structural composite reinforcement applications
The use of structural composite materials demands high homogeneity to ensure efficient load transfer. A wet-laid web process, incorporating 2% by weight of hydroxyethylcellulose (HEC) as a bonding agent, was employed to fabricate non-woven mats, using randomly distributed fibres of a native Mauritius Screwpine ( Pandanus utilis ). Morphological analysis revealed that the resulting mats exhibited superior homogeneity compared to commercial E-glass mats. Three polyester composites were fabricated with fibre mat contents of 10.7%, 21.4%, and 32.1% (corresponding to one, two, and three layers, respectively). The composite with the highest tensile and flexural strengths was selected for manufacturing a 550 mm wind turbine blade (WTB). A flap-wise static test, conducted in accordance with BS EN 61400-2, confirmed that the blade could withstand worst-case loading with a 39% safety margin before failure. The results demonstrate the composite’s suitability for structural applications, with the non-woven mat’s flexibility enabling easy adaptation to complex mould geometries.
- 29 October 2020
- Published by Springer Nature in SN Applied Sciences
- Vol. 2 (11) , 1-13
Using infrared spectrum analyses to predict tensile strength of fibres in a group of closely related plant species: case of Mascarenes Pandanus spp.
- 29 October 2020
- Published by Springer Nature in SN Applied Sciences
- Vol. 2 (11) , 1-13
Using infrared spectrum analyses to predict tensile strength of fibres in a group of closely related plant species: case of Mascarenes Pandanus spp.
- 27 June 2020
- Published by Taylor & Francis in Composite Interfaces
- Vol. 28 (4) , 429-443
Hydroxyethylcellulose use simplifies mat manufacture and improves interfacial cohesion of alkaline-treated Pandanus utilis fibres in polyester composite
A simple method of bonding mutually perpendicular layers of alkaline-treated fibres, through the use of Hydroxyethylcellulose, has been studied as an alternative to woven fibre-mat. Following alkaline process optimisation by using the Taguchi DoE methodology, fibres treatment with 0.5% wt NaOH for 14 hours improved the tensile strength by 36% compared to the untreated fibres. Interfacial-Shear-Stress (measured by pull-out tests) was improved by 32% after the optimal alkaline-treatment. Furthermore, an improvement of 5% in Interfacial-Shear-Stress was achieved after a coating with 2 wt. % Hydroxyethylcellulose. Thus, Hydroxyethylcellulose increases the shear stress, and decreases friction without adverse impact on fibre strength.
- 27 June 2020
- Published by Taylor & Francis in Composite Interfaces
- Vol. 28 (4) , 429-443
Hydroxyethylcellulose use simplifies mat manufacture and improves interfacial cohesion of alkaline-treated Pandanus utilis fibres in polyester composite
A simple method of bonding mutually perpendicular layers of alkaline-treated fibres, through the use of Hydroxyethylcellulose, has been studied as an alternative to woven fibre-mat. Following alkaline process optimisation by using the Taguchi DoE methodology, fibres treatment with 0.5% wt NaOH for 14 hours improved the tensile strength by 36% compared to the untreated fibres. Interfacial-Shear-Stress (measured by pull-out tests) was improved by 32% after the optimal alkaline-treatment. Furthermore, an improvement of 5% in Interfacial-Shear-Stress was achieved after a coating with 2 wt. % Hydroxyethylcellulose. Thus, Hydroxyethylcellulose increases the shear stress, and decreases friction without adverse impact on fibre strength.
- 27 December 2018
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 17 (8) , 1111-1120
Tree Age, Leaf Maturity and Exposure to Sunlight Influence Tensile Strength of Fibres in Pandanus Utilis
Fibers from Pandanus utilis leaves were investigated to determine how fibre strength varies with tree and leaf maturity, exposure to sunlight, leaf degradation state, and fibre position along the leaf. Such information is necessary to optimise leaf harvest to obtain strongest fibres. It has been shown that the strongest fibre comes from a young leaf from a younger tree exposed to the sunlight. Tests and SEM revealed two types of fibres, thin and thick; with the former being stronger. A new method to precisely measure the shape and area of the fibre cross-section, the pre-extraction method that generates optimum-fibre-yield are presented.
- 27 December 2018
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 17 (8) , 1111-1120
Tree Age, Leaf Maturity and Exposure to Sunlight Influence Tensile Strength of Fibres in Pandanus Utilis
Fibers from Pandanus utilis leaves were investigated to determine how fibre strength varies with tree and leaf maturity, exposure to sunlight, leaf degradation state, and fibre position along the leaf. Such information is necessary to optimise leaf harvest to obtain strongest fibres. It has been shown that the strongest fibre comes from a young leaf from a younger tree exposed to the sunlight. Tests and SEM revealed two types of fibres, thin and thick; with the former being stronger. A new method to precisely measure the shape and area of the fibre cross-section, the pre-extraction method that generates optimum-fibre-yield are presented.