QHQing He

Qing He

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Qing He has a total of 13 co-authors. Here are the top co-authors by number of shared publications:

  • Jianping Ao

    Institute of Photoelectronic Thin Film Devices and Technology and Tianjin Key Laboratory of Thin film Devices and Technology, Nankai University, Tianjin 300071, China

    4 shared publications
  • Jinlian Bi

    Tianjin Key Laboratory of Film Electronic and Communication Devices, School of Integrated Circuit Science and Engineering, Tianjin University of Technology, Tianjin, China

    4 shared publications
  • Liann-Be Chang

    Department of Electronic Engineering, Chang Gung University, Taoyuan 333, Taiwan

    4 shared publications
  • Liyong Yao

    Institute of Photoelectronic Thin Film Devices and Technology and Tianjin Key Laboratory of Thin film Devices and Technology, Nankai University, Tianjin 300071, China

    4 shared publications
  • Ming-Jer Jeng

    Department of Electronic Engineering, Chang Gung University, Taoyuan 333, Taiwan

    4 shared publications
  • Shoushuai Gao

    Institute of Photoelectronic Thin Film Devices and Technology and Tianjin Key Laboratory of Thin film Devices and Technology, Nankai University, Tianjin 300071, China

    4 shared publications

Latest Publications

  • Open Access

    Reactive Mechanism of Cu2ZnSnSe4 Thin Films Prepared by Reactive Annealing of the Cu/Zn Metal Layer in a SnSex + Se Atmosphere

    by Liyong Yao, Jianping Ao, Ming-Jer Jeng, Jinlian Bi, Shoushuai Gao, Guozhong Sun, Qing He, Zhiqiang Zhou, Yi Zhang, Yun Sun, et al.

    Cu2ZnSnSe4 (CZTSe) thin films were prepared by a two-step process with the electrodeposition of a Cu/Zn metallic stack precursor followed by a reactive anneal under a Se + Sn containing atmosphere. We investigate the effect of the Sex and SnSex (x = 1,2) partial pressures and annealing temperature on the morphological, structural, and elemental distribution of the CZTSe thin films. Line scanning energy dispersive spectroscopy (EDS) measurements show the presence of a Zn-rich secondary phase at the back-absorber region of the CZTSe thin films processed with higher SnSex partial pressure and lower annealing temperatures. The Zn-rich phase can be reduced by lowering the SnSex partial pressure and by increasing the annealing temperature. A very thin MoSe2 film between the CZTSe and Mo interface is confirmed by X-ray diffraction (XRD) and grazing incidence X-ray diffraction (GIXRD) measurements. These measurements indicate a strong dependence of these process variations in secondary phase formation and accumulation. A possible reaction mechanism of CZTSe thin films was presented. In a preliminary optimization of both the SnSex partial pressure and the reactive annealing process, a solar cell with 7.26% efficiency has been fabricated.


  • Open Access

    Formation of Cl-Doped ZnO Thin Films by a Cathodic Electrodeposition for Use as a Window Layer in CIGS Solar Cells

    by Jianping Ao, Rui Fu, Ming-Jer Jeng, Jinlian Bi, Liyong Yao, Shoushuai Gao, Guozhong Sun, Qing He, Zhiqiang Zhou, Yun Sun, et al.

    Zinc oxide films that are prepared by radio frequency (RF) sputtering are widely used as window layers in copper indium gallium diselenide (CIGS) solar cells. To reduce their production cost, the electrodeposition method for preparing Cl-doped zinc oxide (ZnO:Cl), rather than sputtering, was studied. The electrodeposition parameters of injected current density and the pH of the electrolyte solution were studied. A moderate current density was used to yield high quality zinc oxides. The pH of the electrolyte greatly affected the formation of ZnO films. The pH value of the electrolyte that ensured that zinc oxides of high quality are obtained was close to seven. Electrodeposited ZnO:Cl films had higher transmittance than ZnO:Al films in the near-infrared region and so they can be used to improve the performance of solar cells. Our experiments revealed that the CIGS solar cells with electrodeposited ZnO:Cl films as a window layer were slightly more efficient than those with sputtered ZnO:Al films.


  • Open Access

    Effect of Sn Content in a CuSnZn Metal Precursor on Formation of MoSe2 Film during Selenization in Se+SnSe Vapor

    by Liyong Yao, Jianping Ao, Ming-Jer Jeng, Jinlian Bi, Shoushuai Gao, Guozhong Sun, Qing He, Zhiqiang Zhou, Yun Sun, Liann-Be Chang

    The preparation of Cu2ZnSnSe4 (CZTSe) thin films by the selenization of an electrodeposited copper–tin–zinc (CuSnZn) precursor with various Sn contents in low-pressure Se+SnSex vapor was studied. Scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) measurements revealed that the Sn content of the precursor that is used in selenization in a low-pressure Se+SnSex vapor atmosphere only slightly affects the elemental composition of the formed CZTSe films. However, the Sn content of the precursor significantly affects the grain size and surface morphology of CZTSe films. A metal precursor with a very Sn-poor composition produces CZTSe films with large grains and a rough surface, while a metal precursor with a very Sn-rich composition procures CZTSe films with small grains and a compact surface. X-ray diffraction (XRD) and SEM revealed that the metal precursor with a Sn-rich composition can grow a thicker MoSe2 thin film at CZTSe/Mo interface than one with a Sn-poor composition, possibly because excess Sn in the precursor may catalyze the formation of MoSe2 thin film. A CZTSe solar cell with an efficiency of 7.94%was realized by using an electrodeposited metal precursor with a Sn/Cu ratio of 0.5 in selenization in a low-pressure Se+SnSex vapor.


  • Open Access

    CZTSe solar cells prepared by electrodeposition of Cu/Sn/Zn stack layer followed by selenization at low Se pressure

    by Liyong Yao, Jianping Ao, Ming-Jer Jeng, Jinlian Bi, Shoushuai Gao, Qing He, Zhiqiang Zhou, Guozhong Sun, Yun Sun, Liann-Be Chang, et al.

    Cu2ZnSnSe4 (CZTSe) thin films are prepared by the electrodeposition of stack copper/tin/zinc (Cu/Sn/Zn) precursors, followed by selenization with a tin source at a substrate temperature of 530°C. Three selenization processes were performed herein to study the effects of the source of tin on the quality of CZTSe thin films that are formed at low Se pressure. Much elemental Sn is lost from CZTSe thin films during selenization without a source of tin. The loss of Sn from CZTSe thin films in selenization was suppressed herein using a tin source at 400°C (A2) or 530°C (A3). A copper-poor and zinc-rich CZTSe absorber layer with Cu/Sn, Zn/Sn, Cu/(Zn + Sn), and Zn/(Cu + Zn + Sn) with metallic element ratios of 1.86, 1.24, 0.83, and 0.3, respectively, was obtained in a selenization with a tin source at 530°C. The crystallized CZTSe thin film exhibited an increasingly (112)-preferred orientation at higher tin selenide (SnSe x ) partial pressure. The lack of any obvious Mo-Se phase-related diffraction peaks in the X-ray diffraction (XRD) diffraction patterns may have arisen from the low Se pressure in the selenization processes. The scanning electron microscope (SEM) images reveal a compact surface morphology and a moderate grain size. CZTSe solar cells with an efficiency of 4.81% were produced by the low-cost fabrication process that is elucidated herein.