Habib Dogan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Habib Dogan has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Abdullah Genc
Isparta University of Applied Sciences
21 shared publications - Ibrahim Bahadir Basyigit
ısparta uygulamalı bilimler üniversitesi
14 shared publications - Selcuk Helhel
Department of Electrical & Electronics Engineering, Engineering Faculty, Akdeniz University, 07058 Antalya, Turkey
10 shared publications - Atalay Kocakusak
Akdeniz Universitesi
3 shared publications - Bektas Colak
Department of Physics, Gebze Technical University, Gebze, Trkiye
2 shared publications - Levent Turhan
Research Institute for Fundamental Sciences (TBAE) TÜBİTAK 41470 Gebze Kocaeli Turkey
2 shared publications
Latest Publications
- 25 September 2026
- Published by Muhendislik Bilimleri ve Tasarim Dergisi in Mühendislik Bilimleri ve Tasarım Dergisi
- Vol. 14 (3) , 736-745
SHIFTING THE OPERATING FREQUENCY BAND OF THE WAVEGUIDE FILTER BY CHANGING CSRR TYPE META RESONATORS IN THE SINGLE WAVEGUIDE
In this study, bandpass waveguide filters with resonant frequencies of 5.5 GHz, 6 GHz, and 6.5 GHz are simulated and fabricated by Computer Numerical Control (CNC) milling method. Then, the simulated and measured performance parameters are obtained and compared from 1st order to 7th filter order. By using the same WR-159 waveguide structure, the operating frequency band can be easily shifted by changing only Complementary Split Ring Resonator (CSRR)-type meta-resonators placed in the waveguide, so that the same waveguide structure can be used as a filter in different frequency band regions. The measured insertion loss (IL) values are found to be within the intervals of 0.3-1.88 dB, 0.06-0.49 dB, and 0.43-2.24 dB for the waveguide filters (WGF) at resonance frequencies of 5.5 GHz, 6 GHz, and 6.5 GHz, respectively. Simulated and measured resonance frequencies have good agreement with each other for all filter orders and these values are sufficient to use the filters proposed in this study in many applications.
- 25 September 2026
- Published by Muhendislik Bilimleri ve Tasarim Dergisi in Mühendislik Bilimleri ve Tasarım Dergisi
- Vol. 14 (3) , 736-745
SHIFTING THE OPERATING FREQUENCY BAND OF THE WAVEGUIDE FILTER BY CHANGING CSRR TYPE META RESONATORS IN THE SINGLE WAVEGUIDE
In this study, bandpass waveguide filters with resonant frequencies of 5.5 GHz, 6 GHz, and 6.5 GHz are simulated and fabricated by Computer Numerical Control (CNC) milling method. Then, the simulated and measured performance parameters are obtained and compared from 1st order to 7th filter order. By using the same WR-159 waveguide structure, the operating frequency band can be easily shifted by changing only Complementary Split Ring Resonator (CSRR)-type meta-resonators placed in the waveguide, so that the same waveguide structure can be used as a filter in different frequency band regions. The measured insertion loss (IL) values are found to be within the intervals of 0.3-1.88 dB, 0.06-0.49 dB, and 0.43-2.24 dB for the waveguide filters (WGF) at resonance frequencies of 5.5 GHz, 6 GHz, and 6.5 GHz, respectively. Simulated and measured resonance frequencies have good agreement with each other for all filter orders and these values are sufficient to use the filters proposed in this study in many applications.
- 22 January 2026
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 17 (10) , 1749-1762
A novel modular CSRR-based SLA 3D printed waveguide filter for c-band radar applications: suitable for various substrate thicknesses
The design of filters used in waveguides, which are crucial components of high-frequency communication systems, plays a significant role in improving system performance. In this study, the usage of metamaterials is first proposed, the SLA 3D printing method is used to design and fabricate CSRR meta-resonators-based bandpass waveguide filters (WGFs) with different filter orders for C-band (4-7.5 GHz), and simulated and measured filter performances are compared. Since the proposed novel WG structure is modular, it allows the design of C-band WGFs using different thicknesses of substrate materials. Also, the number of unit elements can be increased and any number of meta-resonators can be inserted to design filters of different orders ranging from 1 to 5. The electrical length of the WGF/WG structure can be changed according to the needs of the applications. The resulting WGFs demonstrated superior RF performance, being 50% lighter than comparable models found in the literature. Over the relevant frequency range, the filter exhibited return losses between 31-43 dB, insertion losses from 0.1 to 0.35 dB, FBW ranging from 12% to 16%, and quality factors between 6.23 and 8.28, depending on the filter order. The obtained experimental results align closely with the simulation predictions, confirming the effectiveness of the design.
- 22 January 2026
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 17 (10) , 1749-1762
A novel modular CSRR-based SLA 3D printed waveguide filter for c-band radar applications: suitable for various substrate thicknesses
The design of filters used in waveguides, which are crucial components of high-frequency communication systems, plays a significant role in improving system performance. In this study, the usage of metamaterials is first proposed, the SLA 3D printing method is used to design and fabricate CSRR meta-resonators-based bandpass waveguide filters (WGFs) with different filter orders for C-band (4-7.5 GHz), and simulated and measured filter performances are compared. Since the proposed novel WG structure is modular, it allows the design of C-band WGFs using different thicknesses of substrate materials. Also, the number of unit elements can be increased and any number of meta-resonators can be inserted to design filters of different orders ranging from 1 to 5. The electrical length of the WGF/WG structure can be changed according to the needs of the applications. The resulting WGFs demonstrated superior RF performance, being 50% lighter than comparable models found in the literature. Over the relevant frequency range, the filter exhibited return losses between 31-43 dB, insertion losses from 0.1 to 0.35 dB, FBW ranging from 12% to 16%, and quality factors between 6.23 and 8.28, depending on the filter order. The obtained experimental results align closely with the simulation predictions, confirming the effectiveness of the design.
- Open Access
- 9 December 2025
- Published by Elsevier in Engineering Science and Technology, an International Journal
- Vol. 72
Novel multi-functional and compact waveguide filter based on various meta-resonators for C-band applications
- 9 December 2025
- Published by Elsevier in Engineering Science and Technology, an International Journal
- Vol. 72
Open AccessNovel multi-functional and compact waveguide filter based on various meta-resonators for C-band applications
- 12 June 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (18)
Electromagnetic Interference Shielding Effectiveness Performance of Various Aluminum Foam/Cellular Structures at C‐Band: A Numerical and Experimental Investigation
Metallic foam or cellular structures are of great interest due to various purposes such as cooling electronics, suppressing acoustic noise, mechanical energy absorption, and electromagnetic (EM) shielding structures. This study investigates three different aluminum foam structures, offset honeycomb (HCF), hybrid‐finned honeycomb (HFHF), and lattice (LF) geometries, to determine their electromagnetic interference shielding effectiveness (SE) performances at the C‐band. Herein, all the developed foams are manufactured by an innovative additive manufacturing‐assisted investment casting technique. A vat polymerization 3D printing technique is used to produce polymer models of designs, and then, the models are used as the casting precursor in the investment flask mold casting process, with vacuum support to produce aluminum foam structures. Throughout the study, the fundamental parameters of each structure are changed to investigate total SE performance variations, which gives a novel glance at the related research field. In the case of a single‐layer structure, the HCF structure is superior by ≈20 dB to HFHF and LF regarding total SE. While the contribution of the absorption and reflection components of HCF and LF are close to ≈5 dB deviation, the contribution of reflection is superior to absorption, close to ≈20 dB deviation for the HFHF structure.
- 12 June 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (18)
Electromagnetic Interference Shielding Effectiveness Performance of Various Aluminum Foam/Cellular Structures at C‐Band: A Numerical and Experimental Investigation
Metallic foam or cellular structures are of great interest due to various purposes such as cooling electronics, suppressing acoustic noise, mechanical energy absorption, and electromagnetic (EM) shielding structures. This study investigates three different aluminum foam structures, offset honeycomb (HCF), hybrid‐finned honeycomb (HFHF), and lattice (LF) geometries, to determine their electromagnetic interference shielding effectiveness (SE) performances at the C‐band. Herein, all the developed foams are manufactured by an innovative additive manufacturing‐assisted investment casting technique. A vat polymerization 3D printing technique is used to produce polymer models of designs, and then, the models are used as the casting precursor in the investment flask mold casting process, with vacuum support to produce aluminum foam structures. Throughout the study, the fundamental parameters of each structure are changed to investigate total SE performance variations, which gives a novel glance at the related research field. In the case of a single‐layer structure, the HCF structure is superior by ≈20 dB to HFHF and LF regarding total SE. While the contribution of the absorption and reflection components of HCF and LF are close to ≈5 dB deviation, the contribution of reflection is superior to absorption, close to ≈20 dB deviation for the HFHF structure.
- Open Access
- 29 January 2025
- Published by Tekirdag Ziraat Fakultesi Dergisi in Tekirdağ Ziraat Fakültesi Dergisi
- Vol. 22 (1) , 151-161
Yeni Bir Mikrodalga Destekli Damıtma Sistemi ile Defne (Laurus nobilis) Bitkisinden Uçucu Yağ Elde Edilmesi
Bu çalışmada, dünyadaki ticaret arzının %90’ı ülkemizden gerçekleştirilen Defne (Laurus nobilis) bitkisinin, geleneksel buharlı damıtma sistemiyle birlikte, endüstriyel tipte tasarlanan yeni bir mikrodalga destekli damıtma (MDD) sistemi kullanılarak uçucu yağları elde edilmiştir. Literatürdeki tıbbi ve aromatik bitkilerden mikrodalga (MD) desteğiyle damıtma yapılan çalışmalara bakıldığında ya küçük ölçekli laboratuvar cihazı ya da klasik MD fırınlara clevenger ilavesi yapılarak damıtma işleminin gerçekleştirildiği görülmektedir. Ancak, bitki miktarı artıkça elektromanyetik (EM) gücün bitkiye nüfuzu azalacağından dolayı bu küçük ölçekli MD destekli çalışmalar endüstriyel tip damıtma süreçleri için birebir model olmaktan uzak kalacaklardır. Bu amaçla bu çalışmada özgünlük olarak, MD gücün büyük ölçekli sistemlerdeki damıtma süreçlerine etkisini doğru bir şekilde modelleyebilmek için yeni bir endüstriyel tip MDD sistemi tasarlanıp test edilmiştir. Her bir testte 5 kg’lık bitki damıtılmakta olup tasarlanan MDD sisteminde 12 adet magnetron kullanılmıştır. Bu magnetronların farklı güçte çalışması kontrol devresiyle sağlanarak, MD gücünün uçucu yağ verimine ve uçucu yağ bileşenlerine etkileri gözlenmiştir. Yapılan testler sonucunda, MD desteği verilerek yapılan damıtma işlemlerinde, Linalool, Linalyle formate ve β-terpinyl acetate bileşenlerinde dramatik değişimler izlenmiştir. Geleneksel buhar damıtma (BD) sistemine göre uçucu yağ veriminde %10-24’lük bir artış elde edilmiş, süre 100 dk’dan 50 dk’ya düşürülmüştür. %26-35 arası daha az enerji harcanmış ve tüm bunların karşılığında bileşen bazında standart değerlerde uçucu yağ elde edilmiştir. Damıtılma sonucundaki uçucu yağ analizleri GC-MS analizi ile kimyasal olarak analiz edilmiş ve 64 farklı bileşen elde edilmiştir. Bunlardan 29 tanesinin gruplandırılmasıyla yapılan değerlendirmede, monoterpen-oksitlerin %55.68, monoterpen-hidrokarbonların ise %27.96 olduğu, kalan kısmın seskiterpen-oksit, seskiterpen-hidrokarbon ve fenolik bileşenlerden oluştuğu tespit edilmiştir. MW gücünün düşük olduğu testlerde monoterpen-oksitlerin azaldığı, MW gücü arttıkça belli bir oranda yükseldiği tespit edilirken monoterpen-hidrokarbonlarda ise tam tersi bir durum izlenmiştir. Linalool ve linalyl formate bileşenleri MW gücüyle en çok değişen bileşenler olmuştur. Yapılan değerlendirmeler MW desteğinin, endüstriyel tip damıtma süreçlerinde uygulanmasının pozitif etkileri olacağı ve maliyetleri aşağı çekeceği yönündedir.
- 29 January 2025
- Published by Tekirdag Ziraat Fakultesi Dergisi in Tekirdağ Ziraat Fakültesi Dergisi
- Vol. 22 (1) , 151-161
Open AccessYeni Bir Mikrodalga Destekli Damıtma Sistemi ile Defne (Laurus nobilis) Bitkisinden Uçucu Yağ Elde Edilmesi
Bu çalışmada, dünyadaki ticaret arzının %90’ı ülkemizden gerçekleştirilen Defne (Laurus nobilis) bitkisinin, geleneksel buharlı damıtma sistemiyle birlikte, endüstriyel tipte tasarlanan yeni bir mikrodalga destekli damıtma (MDD) sistemi kullanılarak uçucu yağları elde edilmiştir. Literatürdeki tıbbi ve aromatik bitkilerden mikrodalga (MD) desteğiyle damıtma yapılan çalışmalara bakıldığında ya küçük ölçekli laboratuvar cihazı ya da klasik MD fırınlara clevenger ilavesi yapılarak damıtma işleminin gerçekleştirildiği görülmektedir. Ancak, bitki miktarı artıkça elektromanyetik (EM) gücün bitkiye nüfuzu azalacağından dolayı bu küçük ölçekli MD destekli çalışmalar endüstriyel tip damıtma süreçleri için birebir model olmaktan uzak kalacaklardır. Bu amaçla bu çalışmada özgünlük olarak, MD gücün büyük ölçekli sistemlerdeki damıtma süreçlerine etkisini doğru bir şekilde modelleyebilmek için yeni bir endüstriyel tip MDD sistemi tasarlanıp test edilmiştir. Her bir testte 5 kg’lık bitki damıtılmakta olup tasarlanan MDD sisteminde 12 adet magnetron kullanılmıştır. Bu magnetronların farklı güçte çalışması kontrol devresiyle sağlanarak, MD gücünün uçucu yağ verimine ve uçucu yağ bileşenlerine etkileri gözlenmiştir. Yapılan testler sonucunda, MD desteği verilerek yapılan damıtma işlemlerinde, Linalool, Linalyle formate ve β-terpinyl acetate bileşenlerinde dramatik değişimler izlenmiştir. Geleneksel buhar damıtma (BD) sistemine göre uçucu yağ veriminde %10-24’lük bir artış elde edilmiş, süre 100 dk’dan 50 dk’ya düşürülmüştür. %26-35 arası daha az enerji harcanmış ve tüm bunların karşılığında bileşen bazında standart değerlerde uçucu yağ elde edilmiştir. Damıtılma sonucundaki uçucu yağ analizleri GC-MS analizi ile kimyasal olarak analiz edilmiş ve 64 farklı bileşen elde edilmiştir. Bunlardan 29 tanesinin gruplandırılmasıyla yapılan değerlendirmede, monoterpen-oksitlerin %55.68, monoterpen-hidrokarbonların ise %27.96 olduğu, kalan kısmın seskiterpen-oksit, seskiterpen-hidrokarbon ve fenolik bileşenlerden oluştuğu tespit edilmiştir. MW gücünün düşük olduğu testlerde monoterpen-oksitlerin azaldığı, MW gücü arttıkça belli bir oranda yükseldiği tespit edilirken monoterpen-hidrokarbonlarda ise tam tersi bir durum izlenmiştir. Linalool ve linalyl formate bileşenleri MW gücüyle en çok değişen bileşenler olmuştur. Yapılan değerlendirmeler MW desteğinin, endüstriyel tip damıtma süreçlerinde uygulanmasının pozitif etkileri olacağı ve maliyetleri aşağı çekeceği yönündedir.
- Open Access
- 16 September 2024
- Published by Turkish Science and Technology Publishing (TURSTEP) in Turkish Journal of Agriculture - Food Science and Technology
- Vol. 12 (9) , 1583-1590
Mikrodalga Destekli Damıtma Sistemi Kullanılarak Anadolu Adaçayı (Salvia fruticosa MILL.) Bitkisinin Sap ve Yapraklarından Elde Edilen Uçucu Yağ Sonuçlarının Karşılaştırılması
Bu çalışmada öncelikle endüstriyel boyutta bir damıtma sistemine mikrodalga desteğinin nasıl sağlanacağı noktasında benzetim çalışmaları yapılmış ve endüstriyel boyutta bir MDD sistemi tasarlanmıştır. Damıtma kazanına 4´3 adet magnetron yerleştirilerek mikrodalga desteği sağlanmıştır. Adaçayı bitkisinin testleri hem geleneksel hem de bu MDD sistemi kullanılarak gerçekleştirilmiştir. Ayrıca, adaçayının sap ve yapraklarıyla birlikte damıtılması veya sadece yapraklarının damıtılarak elde edilen uçucu yağ sonuçları karşılaştırılmıştır. Damıtma sonucu elde edilen uçucu yağların kimyasal analizleri GC-MS cihazı ile yapılmış ve önerilen sistemin damıtma süreçlerine etkileri değerlendirilmiştir. Elde edilen sonuçlara göre, herba kullanılan iki farklı durum için MDD sistemiyle elde edilen yağ verimi geleneksel sisteme göre %10 artmıştır. Herba ve yaprak ayrı ayrı MDD sistemi kullanılarak destile edilmiştir ve sadece yaprakların damıtılması durumunda verim artışı %100 den fazla olmaktadır. Kimyasal bileşenlerdeki değişimler detaylı olarak incelenmiştir.
- 16 September 2024
- Published by Turkish Science and Technology Publishing (TURSTEP) in Turkish Journal of Agriculture - Food Science and Technology
- Vol. 12 (9) , 1583-1590
Open AccessMikrodalga Destekli Damıtma Sistemi Kullanılarak Anadolu Adaçayı (Salvia fruticosa MILL.) Bitkisinin Sap ve Yapraklarından Elde Edilen Uçucu Yağ Sonuçlarının Karşılaştırılması
Bu çalışmada öncelikle endüstriyel boyutta bir damıtma sistemine mikrodalga desteğinin nasıl sağlanacağı noktasında benzetim çalışmaları yapılmış ve endüstriyel boyutta bir MDD sistemi tasarlanmıştır. Damıtma kazanına 4´3 adet magnetron yerleştirilerek mikrodalga desteği sağlanmıştır. Adaçayı bitkisinin testleri hem geleneksel hem de bu MDD sistemi kullanılarak gerçekleştirilmiştir. Ayrıca, adaçayının sap ve yapraklarıyla birlikte damıtılması veya sadece yapraklarının damıtılarak elde edilen uçucu yağ sonuçları karşılaştırılmıştır. Damıtma sonucu elde edilen uçucu yağların kimyasal analizleri GC-MS cihazı ile yapılmış ve önerilen sistemin damıtma süreçlerine etkileri değerlendirilmiştir. Elde edilen sonuçlara göre, herba kullanılan iki farklı durum için MDD sistemiyle elde edilen yağ verimi geleneksel sisteme göre %10 artmıştır. Herba ve yaprak ayrı ayrı MDD sistemi kullanılarak destile edilmiştir ve sadece yaprakların damıtılması durumunda verim artışı %100 den fazla olmaktadır. Kimyasal bileşenlerdeki değişimler detaylı olarak incelenmiştir.
- 6 September 2024
- Published by Elsevier in Measurement
- Vol. 241
Design, fabrication, and experimental validation of a new microwave-assisted distiller for the large-scale industrial systems
- 6 September 2024
- Published by Elsevier in Measurement
- Vol. 241
Design, fabrication, and experimental validation of a new microwave-assisted distiller for the large-scale industrial systems
- 19 June 2024
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 324
Investigation of the radiated emission of honeycomb structured aluminum foam/cellular heatsinks at 1–10 GHz
- 19 June 2024
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 324
Investigation of the radiated emission of honeycomb structured aluminum foam/cellular heatsinks at 1–10 GHz
- Open Access
- 15 June 2024
- Published by Isparta Uygulamali Bilimler Universitesi in Türk Bilim ve Mühendislik Dergisi
- Vol. 6 (1) , 1-7
Yüz Tanıma Tabanlı Öğrenci Takip Sistemi
Teknolojinin hızlı bir şekilde gelişmesi otomasyon sistemlerinde farklı yaklaşımların ortaya çıkmasını netice vermiş ve biyometrik temelli tanımaların yoğun bir şekilde kullanımını doğurmuştur. Bu çalışmada öğrencilerin bir derse devam süreçlerinin etkili ve kolay bir şekilde yapılabilmesi ve yaşanacak zaman israfının önüne geçilmesi amacıyla biyometrik temelli sistemlerden yüz tanıma işlemi kullanılarak sınıf yoklama sistemi geliştirilmiştir. Phyton programlama dili ve OpenCV kütüphanesi kullanılarak gerçekleştirilen uygulama ile hem tekli ve çoklu yüz tanıma işlemleri hem de tıbbi maske takılma durumundaki yüz tanıma işlemleri başarılı bir şekilde gerçekleştirilmiştir. Derse kayıtlı olmayan öğrencilerin misafir öğrenci olarak kodlandığı sistemde, istenildiği durumlarda sesli uyarı ile de yüzü tanınan öğrencinin isminin seslendirilmesi de sağlanabilmektedir. Sonuçlar bir CSV uzantılı dosyada tarih temelli olarak depolanmakta istenildiği takdirde öğrencilerin devam durumları istatistiksel olarak analiz edilebilmektedir. Çalışmanın eğitim kurumlarındaki devam süreçlerinde iyileştirmeler sağlayacağı ve uygulanması durumunda farklı mobil platformlarla desteklenerek çok daha efektif hale getirilebileceği öngörülmektedir.
- 15 June 2024
- Published by Isparta Uygulamali Bilimler Universitesi in Türk Bilim ve Mühendislik Dergisi
- Vol. 6 (1) , 1-7
Open AccessYüz Tanıma Tabanlı Öğrenci Takip Sistemi
Teknolojinin hızlı bir şekilde gelişmesi otomasyon sistemlerinde farklı yaklaşımların ortaya çıkmasını netice vermiş ve biyometrik temelli tanımaların yoğun bir şekilde kullanımını doğurmuştur. Bu çalışmada öğrencilerin bir derse devam süreçlerinin etkili ve kolay bir şekilde yapılabilmesi ve yaşanacak zaman israfının önüne geçilmesi amacıyla biyometrik temelli sistemlerden yüz tanıma işlemi kullanılarak sınıf yoklama sistemi geliştirilmiştir. Phyton programlama dili ve OpenCV kütüphanesi kullanılarak gerçekleştirilen uygulama ile hem tekli ve çoklu yüz tanıma işlemleri hem de tıbbi maske takılma durumundaki yüz tanıma işlemleri başarılı bir şekilde gerçekleştirilmiştir. Derse kayıtlı olmayan öğrencilerin misafir öğrenci olarak kodlandığı sistemde, istenildiği durumlarda sesli uyarı ile de yüzü tanınan öğrencinin isminin seslendirilmesi de sağlanabilmektedir. Sonuçlar bir CSV uzantılı dosyada tarih temelli olarak depolanmakta istenildiği takdirde öğrencilerin devam durumları istatistiksel olarak analiz edilebilmektedir. Çalışmanın eğitim kurumlarındaki devam süreçlerinde iyileştirmeler sağlayacağı ve uygulanması durumunda farklı mobil platformlarla desteklenerek çok daha efektif hale getirilebileceği öngörülmektedir.