Oliver Hering
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Oliver Hering has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Ahmet Erman Tekkaya
TU Dortmund
8 shared publications A. Erman Tekkaya
Institute of Forming Technology and Lightweight Components, TU Dortmund University, Dortmund, Germany
3 shared publications- Frank Walther
Chair of Materials Test Engineering (WPT) TU Dortmund University Dortmund Germany
3 shared publications - André Schulze
Institute of Forming Technology and Lightweight Components , Baroper Street 303, 44227 Dortmund , Germany
2 shared publications - Felix Kolpak
Institute of Forming Technology and Lightweight Components , Baroper Strasse 303, 44227 Dortmund , Germany
2 shared publications - Richard Ostwald
Engineering Mechanics, Paderborn University, 33098 Paderborn, Germany
2 shared publications
Latest Publications
- 1 December 2022
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 145 (1) , 1-29
Controlling Damage Evolution in Geometrically Identical Cold Forged Parts by Counterpressure
It is investigated to what extent the evolution of ductile damage in cold forging can be controlled without changing the geometry of the produced part. Besides the effects of strain hardening and residual stresses, damage, which is the nucleation, growth and coalescence of voids on microscopic level, affects product properties of the manufactured components such as fatigue strength, impact strength, or elastic stiffness. Former investigations have shown that the load path-dependent damage evolution in forward rod extrusion, and thus, the performance of produced parts can be controlled by the process parameters extrusion strain and shoulder opening angle. As these parameters also affect the geometry of extruded parts, design requirements of components might be violated by varying these. Thus, counterpressure is used to superpose purely hydrostatic stresses to forward rod extrusion in order to decrease triaxiality in the forming zone without causing geometric variations in the produced parts. The counterpressure is either introduced by a counterpunch or by modified process routes. The achieved improvements in product performance are in agreement with results obtained by variation of extrusion strain and shoulder opening angle as described in the literature. In addition, it is observed in tensile tests that damage in cold extruded parts does not significantly affect flow stress. All advancements in product performance are realized without affecting the products’ geometries.
- 1 December 2022
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 145 (1) , 1-29
Controlling Damage Evolution in Geometrically Identical Cold Forged Parts by Counterpressure
It is investigated to what extent the evolution of ductile damage in cold forging can be controlled without changing the geometry of the produced part. Besides the effects of strain hardening and residual stresses, damage, which is the nucleation, growth and coalescence of voids on microscopic level, affects product properties of the manufactured components such as fatigue strength, impact strength, or elastic stiffness. Former investigations have shown that the load path-dependent damage evolution in forward rod extrusion, and thus, the performance of produced parts can be controlled by the process parameters extrusion strain and shoulder opening angle. As these parameters also affect the geometry of extruded parts, design requirements of components might be violated by varying these. Thus, counterpressure is used to superpose purely hydrostatic stresses to forward rod extrusion in order to decrease triaxiality in the forming zone without causing geometric variations in the produced parts. The counterpressure is either introduced by a counterpunch or by modified process routes. The achieved improvements in product performance are in agreement with results obtained by variation of extrusion strain and shoulder opening angle as described in the literature. In addition, it is observed in tensile tests that damage in cold extruded parts does not significantly affect flow stress. All advancements in product performance are realized without affecting the products’ geometries.
- Open Access
- 22 October 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing-Green Technology
- Vol. 9 (4) , 1035-1048
Production and Subsequent Forming of Chip-Based Aluminium Sheets Without Remelting
Bent components and deep drawn cups are produced by direct usage of aluminium chips without melting following a new process chain: hot extrusion of aluminium chips to a cylindrical open profile, flattening, subsequent rolling and bending or deep drawing. The properties of the hot extruded chip-based AA6060 sheets are examined by tensile tests and microstructural investigations and the results are compared with those obtained from material extruded from conventional cast billets. The chip-based sheets were used to form components by bending or deep drawing. No significant differences between the bent components or deep-drawn cups made of chips and those from cast material are observed regarding their capability for further plastic forming operations. This makes the new process route a resource-efficient alternative for the production of aluminium sheet products.
- 22 October 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing-Green Technology
- Vol. 9 (4) , 1035-1048
Open AccessProduction and Subsequent Forming of Chip-Based Aluminium Sheets Without Remelting
Bent components and deep drawn cups are produced by direct usage of aluminium chips without melting following a new process chain: hot extrusion of aluminium chips to a cylindrical open profile, flattening, subsequent rolling and bending or deep drawing. The properties of the hot extruded chip-based AA6060 sheets are examined by tensile tests and microstructural investigations and the results are compared with those obtained from material extruded from conventional cast billets. The chip-based sheets were used to form components by bending or deep drawing. No significant differences between the bent components or deep-drawn cups made of chips and those from cast material are observed regarding their capability for further plastic forming operations. This makes the new process route a resource-efficient alternative for the production of aluminium sheet products.
- Open Access
Increasing the Lightweight Potential of Composite Cold Forging by Utilizing Magnesium and Granular Cores
In this paper a process sequence, that uses forward rod extrusion with cold forged C15 steel cup billets to produce lightweight shafts, is presented. The steel cup billets feature either a lightweight magnesium alloy core or a granular medium core that is removed after forming to obtain hollow shafts without the need of complex tools and highly loaded mandrels. It is shown that composite shafts featuring magnesium cores can be produced for a wide range of extrusion strains. Due to high hydrostic pressures in forward rod extrusion, the forming limit of magnesium at room temperature can be expanded. The observed bond strength between core and sheath is below the shear yield strength of utilized magnesium AZ31 alloy. Hollow shafts are successfully produced with the presented process route by utilizing zirconium oxide beads or quartz sand as a lost core. As the law of constant volume in metal forming is violated by compressible granular media, a simulation approach using a modified Drucker-Prager yield surface to model these materials is validated to provide a tool for efficient process design. Granular cores and magnesium alloy cores offer new possibilities in production of lightweight shafts by means of composite cold forging. Both process variants allow for higher weight savings than composite shafts based on aluminum cores.
Open AccessIncreasing the Lightweight Potential of Composite Cold Forging by Utilizing Magnesium and Granular Cores
In this paper a process sequence, that uses forward rod extrusion with cold forged C15 steel cup billets to produce lightweight shafts, is presented. The steel cup billets feature either a lightweight magnesium alloy core or a granular medium core that is removed after forming to obtain hollow shafts without the need of complex tools and highly loaded mandrels. It is shown that composite shafts featuring magnesium cores can be produced for a wide range of extrusion strains. Due to high hydrostic pressures in forward rod extrusion, the forming limit of magnesium at room temperature can be expanded. The observed bond strength between core and sheath is below the shear yield strength of utilized magnesium AZ31 alloy. Hollow shafts are successfully produced with the presented process route by utilizing zirconium oxide beads or quartz sand as a lost core. As the law of constant volume in metal forming is violated by compressible granular media, a simulation approach using a modified Drucker-Prager yield surface to model these materials is validated to provide a tool for efficient process design. Granular cores and magnesium alloy cores offer new possibilities in production of lightweight shafts by means of composite cold forging. Both process variants allow for higher weight savings than composite shafts based on aluminum cores.
- 1 May 2020
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 279
Damage-induced performance variations of cold forged parts
- 1 May 2020
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 279
Damage-induced performance variations of cold forged parts
- 2 January 2020
- Published by Springer Nature in Production Engineering
- Vol. 14 (1) , 115-121
Influence of anisotropic damage evolution on cold forging
- 2 January 2020
- Published by Springer Nature in Production Engineering
- Vol. 14 (1) , 115-121
Influence of anisotropic damage evolution on cold forging
- 14 December 2019
- Published by Springer Nature in Production Engineering
- Vol. 14 (1) , 33-41
Prediction and analysis of damage evolution during caliber rolling and subsequent cold forward extrusion
- 14 December 2019
- Published by Springer Nature in Production Engineering
- Vol. 14 (1) , 33-41
Prediction and analysis of damage evolution during caliber rolling and subsequent cold forward extrusion
- 27 November 2019
- Published by Springer Nature in International Journal of Material Forming
- Vol. 13 (6) , 1003-1014
Characterization of damage in forward rod extruded parts
- 27 November 2019
- Published by Springer Nature in International Journal of Material Forming
- Vol. 13 (6) , 1003-1014
Characterization of damage in forward rod extruded parts
- 18 November 2019
- Published by Springer Nature in Production Engineering
- Vol. 14 (1) , 77-85
Micro-magnetic damage characterization of bent and cold forged parts
- 18 November 2019
- Published by Springer Nature in Production Engineering
- Vol. 14 (1) , 77-85
Micro-magnetic damage characterization of bent and cold forged parts
- Open Access
- 2 January 2019
- Published by Springer Nature in International Journal of Material Forming
- Vol. 12 (6) , 955-972
Flow curves up to high strains considering load reversal and damage
- 2 January 2019
- Published by Springer Nature in International Journal of Material Forming
- Vol. 12 (6) , 955-972
Open AccessFlow curves up to high strains considering load reversal and damage
- 1 January 2017
- Published by Elsevier in CIRP Annals
- Vol. 66 (1) , 281-284
Forming-induced damage and its effects on product properties
- 1 January 2017
- Published by Elsevier in CIRP Annals
- Vol. 66 (1) , 281-284
Forming-induced damage and its effects on product properties