Felix Kolpak
Felix Kolpak has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Ahmet Erman Tekkaya
TU Dortmund
5 shared publications - Christoph Dahnke
Bulk metal forming, Institute of Forming Technology and Lightweight Components, Baroper Straße 303, Dortmund, 44227, GERMANY
2 shared publications - Oliver Hering
Institute of Forming Technology and Lightweight Components, TU Dortmund University, Dortmund, Germany
2 shared publications A. Erman Tekkaya
Institute of Forming Technology and Lightweight Components (IUL), TU Dortmund University, Dortmund, Germany
1 shared publication- André Schulze
Institute of Forming Technology and Lightweight Components , Baroper Street 303, 44227 Dortmund , Germany
1 shared publication - Anna Komodromos
Institute of Forming Technology and Lightweight Components (IUL), TU Dortmund University, Dortmund, Germany
1 shared publication
Latest Publications
- 28 February 2024
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 146 (4) , 1-53
Characterization of Tool Surface Properties Generated by Directed Energy Deposition and Subsequent Ball Burnishing
By Directed Energy Deposition (DED) a flexible design of cooling channels in forming tools, e.g. hot stamping, with a variety of sizes and a high positioning flexibility compared to machining processes is possible. The subsequent ball burnishing of the tool surfaces in combination with a variation of the DED process parameters enables a control of the tool surface properties and the friction behavior. Parameters such as the ball burnishing pressure or the path overlapping in the DED process are investigated to quantify their effects on roughness, hardness, friction, residual stresses and heat transfer coefficient of generic tool surfaces. The friction coefficient at elevated temperatures depends strongly on the surface roughness of the tool steel surfaces generated by DED and ball burnishing. The latter process improves the surface integrity: the roughness peaks are leveled by up to 75 %, the hardness and the residual stresses are enhanced by up to 20 % and 70 %, respectively. However, the roughness of the tool surfaces is determined mainly by the path overlapping of the welded beads in the DED process. Despite the higher surface roughness, the heat transfer coefficient is in the range of conventionally manufactured tool surfaces of up to 2,700 W/m2K for contact pressures up to 40 MPa. First hot stamping experiments demonstrate that the tools manufactured by the novel process combination are able to manufacture 22MnB5 hat profiles with an increased and more homogenous hardness as well as more homogeneous thickness distribution compared to conventionally manufactured tools.
- 28 February 2024
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 146 (4) , 1-53
Characterization of Tool Surface Properties Generated by Directed Energy Deposition and Subsequent Ball Burnishing
By Directed Energy Deposition (DED) a flexible design of cooling channels in forming tools, e.g. hot stamping, with a variety of sizes and a high positioning flexibility compared to machining processes is possible. The subsequent ball burnishing of the tool surfaces in combination with a variation of the DED process parameters enables a control of the tool surface properties and the friction behavior. Parameters such as the ball burnishing pressure or the path overlapping in the DED process are investigated to quantify their effects on roughness, hardness, friction, residual stresses and heat transfer coefficient of generic tool surfaces. The friction coefficient at elevated temperatures depends strongly on the surface roughness of the tool steel surfaces generated by DED and ball burnishing. The latter process improves the surface integrity: the roughness peaks are leveled by up to 75 %, the hardness and the residual stresses are enhanced by up to 20 % and 70 %, respectively. However, the roughness of the tool surfaces is determined mainly by the path overlapping of the welded beads in the DED process. Despite the higher surface roughness, the heat transfer coefficient is in the range of conventionally manufactured tool surfaces of up to 2,700 W/m2K for contact pressures up to 40 MPa. First hot stamping experiments demonstrate that the tools manufactured by the novel process combination are able to manufacture 22MnB5 hat profiles with an increased and more homogenous hardness as well as more homogeneous thickness distribution compared to conventionally manufactured tools.
- Open Access
- 21 October 2021
- Published by Springer Nature in International Journal of Material Forming
- Vol. 14 (6) , 1463-1481
Consequences of large strain anisotropic work-hardening in cold forging
The influence of anisotropic work-hardening on the component properties and process forces in cold forging is investigated. The focus is on the material behaviour exhibited after strain path reversals. The work-hardening of three steels is characterized for large monotonic strains (equivalent strains up to 1.7) and subsequent strain path reversals (accumulated strains up to 2.5). Tensile tests on specimens extracted from rods forward extruded at room temperature reveal an almost linear work-hardening for all investigated steels. The application of compressive tests on extruded material gives insights into the non-monotonic work-hardening behaviour. All previously reported anisotropic work-hardening phenomena such as the Bauschinger effect, work-hardening stagnation and permanent softening are present for all investigated steels and intensify with the pre-strain. Experimental results of 16MnCrS5 were utilized to select constitutive models of increasing complexity regarding their capability to capture anisotropic work-hardening. The best fit between experimental and numerical data was obtained by implementation of a modified Yoshida-Uemori model, which is able to capture all observed anisotropic work-hardening phenomena. The constitutive models were applied in simulations of single- and multi-stage cold forming processes, revealing the significant effect of anisotropic hardening on the predicted component properties and process forces, originating in the process-intrinsic strain path reversals as well as in strain path reversals between subsequent forming stages. Selected results were validated experimentally.
- 21 October 2021
- Published by Springer Nature in International Journal of Material Forming
- Vol. 14 (6) , 1463-1481
Open AccessConsequences of large strain anisotropic work-hardening in cold forging
The influence of anisotropic work-hardening on the component properties and process forces in cold forging is investigated. The focus is on the material behaviour exhibited after strain path reversals. The work-hardening of three steels is characterized for large monotonic strains (equivalent strains up to 1.7) and subsequent strain path reversals (accumulated strains up to 2.5). Tensile tests on specimens extracted from rods forward extruded at room temperature reveal an almost linear work-hardening for all investigated steels. The application of compressive tests on extruded material gives insights into the non-monotonic work-hardening behaviour. All previously reported anisotropic work-hardening phenomena such as the Bauschinger effect, work-hardening stagnation and permanent softening are present for all investigated steels and intensify with the pre-strain. Experimental results of 16MnCrS5 were utilized to select constitutive models of increasing complexity regarding their capability to capture anisotropic work-hardening. The best fit between experimental and numerical data was obtained by implementation of a modified Yoshida-Uemori model, which is able to capture all observed anisotropic work-hardening phenomena. The constitutive models were applied in simulations of single- and multi-stage cold forming processes, revealing the significant effect of anisotropic hardening on the predicted component properties and process forces, originating in the process-intrinsic strain path reversals as well as in strain path reversals between subsequent forming stages. Selected results were validated experimentally.
- Open Access
Increasing the Lightweight Potential of Composite Cold Forging by Utilizing Magnesium and Granular Cores
In this paper a process sequence, that uses forward rod extrusion with cold forged C15 steel cup billets to produce lightweight shafts, is presented. The steel cup billets feature either a lightweight magnesium alloy core or a granular medium core that is removed after forming to obtain hollow shafts without the need of complex tools and highly loaded mandrels. It is shown that composite shafts featuring magnesium cores can be produced for a wide range of extrusion strains. Due to high hydrostic pressures in forward rod extrusion, the forming limit of magnesium at room temperature can be expanded. The observed bond strength between core and sheath is below the shear yield strength of utilized magnesium AZ31 alloy. Hollow shafts are successfully produced with the presented process route by utilizing zirconium oxide beads or quartz sand as a lost core. As the law of constant volume in metal forming is violated by compressible granular media, a simulation approach using a modified Drucker-Prager yield surface to model these materials is validated to provide a tool for efficient process design. Granular cores and magnesium alloy cores offer new possibilities in production of lightweight shafts by means of composite cold forging. Both process variants allow for higher weight savings than composite shafts based on aluminum cores.
Open AccessIncreasing the Lightweight Potential of Composite Cold Forging by Utilizing Magnesium and Granular Cores
In this paper a process sequence, that uses forward rod extrusion with cold forged C15 steel cup billets to produce lightweight shafts, is presented. The steel cup billets feature either a lightweight magnesium alloy core or a granular medium core that is removed after forming to obtain hollow shafts without the need of complex tools and highly loaded mandrels. It is shown that composite shafts featuring magnesium cores can be produced for a wide range of extrusion strains. Due to high hydrostic pressures in forward rod extrusion, the forming limit of magnesium at room temperature can be expanded. The observed bond strength between core and sheath is below the shear yield strength of utilized magnesium AZ31 alloy. Hollow shafts are successfully produced with the presented process route by utilizing zirconium oxide beads or quartz sand as a lost core. As the law of constant volume in metal forming is violated by compressible granular media, a simulation approach using a modified Drucker-Prager yield surface to model these materials is validated to provide a tool for efficient process design. Granular cores and magnesium alloy cores offer new possibilities in production of lightweight shafts by means of composite cold forging. Both process variants allow for higher weight savings than composite shafts based on aluminum cores.
- 1 December 2019
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 274
Predicting weld-quality in direct hot extrusion of aluminium chips
- 1 December 2019
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 274
Predicting weld-quality in direct hot extrusion of aluminium chips
- 1 April 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 10, 201-208
Manufacturing of reinforced profiles by means of combined continuous and discontinuous composite extrusion
- 1 April 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 10, 201-208
Manufacturing of reinforced profiles by means of combined continuous and discontinuous composite extrusion
- Open Access
- 2 January 2019
- Published by Springer Nature in International Journal of Material Forming
- Vol. 12 (6) , 955-972
Flow curves up to high strains considering load reversal and damage
- 2 January 2019
- Published by Springer Nature in International Journal of Material Forming
- Vol. 12 (6) , 955-972
Open AccessFlow curves up to high strains considering load reversal and damage