Saifu Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Saifu Wang has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Chong Li
Jiangsu University, Zhenjiang, 212013, CHINA
7 shared publications - Vitus Mwinteribo Tabie
Department of Mechanical Engineering Wa Polytechnic, Ghana, P. O. Box 553, Wa, UWR, GHANA
5 shared publications - Xiaojing Xu
Institute of Advanced Manufacturing and Modern Equipment Technology, Jiangsu University, Zhenjiang, China
5 shared publications - Chengbin Cai
Jiangsu University, Zhenjiang, 212013, CHINA
4 shared publications Song Yang
3 shared publicationsXiaojing Xu
3 shared publications
Latest Publications
- Open Access
- 1 November 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (11) , 116523
Effect of B4Cp content on microstructure and the high-temperature oxidation behavior of Ti-5.4Al-4.03Mo-3.93V-2.37Cr-0.01Zr composites
The paper discusses the effects of B4C particle (B4Cp) content on the microstructure and high-temperature oxidation resistance of B4Cp/Ti-5.4Al-4.03Mo-3.93V-2.37Cr-0.01Zr composite prepared by powder metallurgy. The results demonstrate that grain size of the composites decreases by increasing reinforcement content from 1 to 3 wt.%, suggesting that B4Cp can refine grain of the materials. For the composites with increasing B4Cp content from 0 to 3 wt.%, the apparent porosity increase from 3.23 to 6.89%, indicating that the density of materials decreased with the increase of B4CP content. In addition, the hardness of the materials have been greatly improved. Comparing to the substrate 434.02 HV, the 1, 2, and 3 wt.% B4CP specimens are increased by 37.2%, 57.5%, and 84.7%, respectively. The weight of the oxidation product is reduced and the oxidation rate is slowed down, as the B4CP content increases. Moreover, the thickness of the oxide layer is greatly reduced, and the thickness of oxidation layer in composites with 0, 1, 2 and 3 wt.% B4CP specimens were 60, 55, 47 and 40 μm, indicating that B4CP can improve the high-temperature oxidation resistance.
- 1 November 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (11) , 116523
Open AccessEffect of B4Cp content on microstructure and the high-temperature oxidation behavior of Ti-5.4Al-4.03Mo-3.93V-2.37Cr-0.01Zr composites
The paper discusses the effects of B4C particle (B4Cp) content on the microstructure and high-temperature oxidation resistance of B4Cp/Ti-5.4Al-4.03Mo-3.93V-2.37Cr-0.01Zr composite prepared by powder metallurgy. The results demonstrate that grain size of the composites decreases by increasing reinforcement content from 1 to 3 wt.%, suggesting that B4Cp can refine grain of the materials. For the composites with increasing B4Cp content from 0 to 3 wt.%, the apparent porosity increase from 3.23 to 6.89%, indicating that the density of materials decreased with the increase of B4CP content. In addition, the hardness of the materials have been greatly improved. Comparing to the substrate 434.02 HV, the 1, 2, and 3 wt.% B4CP specimens are increased by 37.2%, 57.5%, and 84.7%, respectively. The weight of the oxidation product is reduced and the oxidation rate is slowed down, as the B4CP content increases. Moreover, the thickness of the oxide layer is greatly reduced, and the thickness of oxidation layer in composites with 0, 1, 2 and 3 wt.% B4CP specimens were 60, 55, 47 and 40 μm, indicating that B4CP can improve the high-temperature oxidation resistance.
- Open Access
- 1 December 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 1265b7
Effect of La2O3 on resistance to high-temperature oxidation and corrosion of aluminized and aluminum-chrome coating
- 1 December 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 1265b7
Open AccessEffect of La2O3 on resistance to high-temperature oxidation and corrosion of aluminized and aluminum-chrome coating
- 4 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 1065b3
Microstructure and properties of Ti-Al-Sn-Zr-Nb-Si matrix composite reinforced with in-situ TiC and Ti5Si3 prepared by powder metallurgy
- 4 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 1065b3
Microstructure and properties of Ti-Al-Sn-Zr-Nb-Si matrix composite reinforced with in-situ TiC and Ti5Si3 prepared by powder metallurgy
- 21 August 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 106549
Effect of pre-recovery on microstructure and properties of rolled Al-12.51Zn-2.85Mg-2.83Cu-0.18Zr-0.06Sr aluminum alloy
- 21 August 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 106549
Effect of pre-recovery on microstructure and properties of rolled Al-12.51Zn-2.85Mg-2.83Cu-0.18Zr-0.06Sr aluminum alloy
- 4 June 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (8) , 0865h1
Effect of extrusion-Bc ECA integration technology on microstructure and properties of Al–Zn–Mg–Cu–Zr alloy
Smelting, homogenizing annealing, traditional extrusion, extrusion-Bc integrated large strain technology, and solid solution aging process were sequentially adopted for an independently designed aluminum alloy. The microstructure and properties of the material were characterized by metallographic microscopy, field emission scanning electron microscope (SEM), EBSD tester of EDAX TEAM, X-ray diffraction (XRD), HV-1000 microhardness tester, and domestic WDW-200 microcomputer-controlled universal testing machine. Experimental results show that the grain size of the aluminum alloy was obviously reduced after the extrusion-Bc ECA processing. The average grain size was reduced from 12.1 μm to 6.9 μm. Although the tensile strength of the alloy was reduced, the plasticity was greatly improved. Moreover, the intergranular corrosion resistance of the alloy was greatly improved. The depth of intergranular corrosion was reduced from 245.0 μm to 39.7 μm, and the grade of intergranular corrosion of the alloy is from grade 4 to grade 3. The extrusion-Bc ECA processing of Al-Zn-Mg-Cu-Zr Alloy followed by solution-aging greatly improves the toughness, intergranular corrosion resistance and decreases grain size of the alloy.
- 4 June 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (8) , 0865h1
Effect of extrusion-Bc ECA integration technology on microstructure and properties of Al–Zn–Mg–Cu–Zr alloy
Smelting, homogenizing annealing, traditional extrusion, extrusion-Bc integrated large strain technology, and solid solution aging process were sequentially adopted for an independently designed aluminum alloy. The microstructure and properties of the material were characterized by metallographic microscopy, field emission scanning electron microscope (SEM), EBSD tester of EDAX TEAM, X-ray diffraction (XRD), HV-1000 microhardness tester, and domestic WDW-200 microcomputer-controlled universal testing machine. Experimental results show that the grain size of the aluminum alloy was obviously reduced after the extrusion-Bc ECA processing. The average grain size was reduced from 12.1 μm to 6.9 μm. Although the tensile strength of the alloy was reduced, the plasticity was greatly improved. Moreover, the intergranular corrosion resistance of the alloy was greatly improved. The depth of intergranular corrosion was reduced from 245.0 μm to 39.7 μm, and the grade of intergranular corrosion of the alloy is from grade 4 to grade 3. The extrusion-Bc ECA processing of Al-Zn-Mg-Cu-Zr Alloy followed by solution-aging greatly improves the toughness, intergranular corrosion resistance and decreases grain size of the alloy.
- 29 May 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (8) , 086444
High-temperature oxidation and hot corrosion behavior of the Cr-modified aluminide coating obtained by a Thermal Diffusion process
- 29 May 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (8) , 086444
High-temperature oxidation and hot corrosion behavior of the Cr-modified aluminide coating obtained by a Thermal Diffusion process
- 16 January 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (4) , 046426
Microstructure and properties of Al and Al-Cr coatings on nickel-based superalloy GH625 by a thermal diffusion process
Aluminide coating has been known as one of the best surface engineering approaches to combat high temperature corrosion in nickel-based superalloy. In this paper, A chromium-modified aluminide coating was prepared on the GH625 by the neutral salt bath method. The microstructure and properties of the modified coating was studied and compared with simple-aluminized coating by scanning electron microscope, x-ray diffraction techniques, depth elemental profiling analysis, microhardness and interface bonding force test. Surface SEM and EDS analysis show that the Al-Cr coating contains more Cr element, finer microstructure and fewer oxide inclusions. Surface XRD analysis shows that the phase structure of Al-Cr coating is different and the α-Cr phase has replaced Ni3Al and Al4CrNi15 phases in the Al coating. Cross section SEM and line scan analysis show that the microstructure of Al-Cr coating is more compact and the element distribution is more uniform than the Al coating. In addition, there is a significantly wider interface zone in the Al-Cr coating than that of Al coating. In the interface zone, there is an obvious Cr-rich area and a wider elemental diffusion area toward the substrate. As the result, the Al-Cr coating has higher microhardness and the interfacial bonding force between the coating and the substrate.
- 16 January 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (4) , 046426
Microstructure and properties of Al and Al-Cr coatings on nickel-based superalloy GH625 by a thermal diffusion process
Aluminide coating has been known as one of the best surface engineering approaches to combat high temperature corrosion in nickel-based superalloy. In this paper, A chromium-modified aluminide coating was prepared on the GH625 by the neutral salt bath method. The microstructure and properties of the modified coating was studied and compared with simple-aluminized coating by scanning electron microscope, x-ray diffraction techniques, depth elemental profiling analysis, microhardness and interface bonding force test. Surface SEM and EDS analysis show that the Al-Cr coating contains more Cr element, finer microstructure and fewer oxide inclusions. Surface XRD analysis shows that the phase structure of Al-Cr coating is different and the α-Cr phase has replaced Ni3Al and Al4CrNi15 phases in the Al coating. Cross section SEM and line scan analysis show that the microstructure of Al-Cr coating is more compact and the element distribution is more uniform than the Al coating. In addition, there is a significantly wider interface zone in the Al-Cr coating than that of Al coating. In the interface zone, there is an obvious Cr-rich area and a wider elemental diffusion area toward the substrate. As the result, the Al-Cr coating has higher microhardness and the interfacial bonding force between the coating and the substrate.