Vitus Mwinteribo Tabie
Vitus Mwinteribo Tabie has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Chong Li
Jiangsu University, Zhenjiang, 212013, CHINA
7 shared publications - Ze Jiang
Jiangsu University, Engineering Institute of Advanced Manufacturing and Modern Equipment Technology, China, Zhenjiang, ZhenJiang, JiangSu, 212013, CHINA
7 shared publications Xiaojing Xu
Department of Mechanical Engineering, Hilla Limann Technical University, Wa, Upper West Region, Ghana
6 shared publications- Xiaojing Xu
Institute of Advanced Manufacturing and Modern Equipment Technology, Jiangsu University, Zhenjiang, China
6 shared publications - Qingjun Liu
Jiangsu University, Engineering Institute of Advanced Manufacturing and Modern Equipment Technology, ZhenJiang, JiangSu, CHINA
5 shared publications - Saifu Wang
Jiangsu Univ, Engn Inst Adv Mfg & Modern Equipment Technol, Zhenjiang 212013, Jiangsu, Peoples R China
5 shared publications
Latest Publications
- Open Access
- 5 May 2025
- Published by Springer Nature in Journal of Engineering and Applied Science
- Vol. 72 (1) , 1-24
Properties of particle-reinforced titanium matrix composites produced by powder metallurgy—current research
Particle-reinforced titanium matrix composites (TMCs) have been an area of active research in recent times. This is because of their high specific strength, excellent mechanical properties, and aversion to corrosion which makes them ideal for aerospace, automotive, and biomedical applications. The mechanical and physical properties of TMCs rely on the reinforcement phases and the processing route. Carbides, borides, nitrides, oxides, silicides, and graphene/carbon-matrix reinforcements for TMCs are broadly adopted. Powder metallurgy (PM) is a widely used method for the production of TMCs. This study reviews the common particles that are used as reinforcements in TMCs, their properties, production, the PM techniques used for consolidating them in TMCs, and their effect on the TMCs produced. Current literature and developments in TMCs have also been considered in this review.
- 5 May 2025
- Published by Springer Nature in Journal of Engineering and Applied Science
- Vol. 72 (1) , 1-24
Open AccessProperties of particle-reinforced titanium matrix composites produced by powder metallurgy—current research
Particle-reinforced titanium matrix composites (TMCs) have been an area of active research in recent times. This is because of their high specific strength, excellent mechanical properties, and aversion to corrosion which makes them ideal for aerospace, automotive, and biomedical applications. The mechanical and physical properties of TMCs rely on the reinforcement phases and the processing route. Carbides, borides, nitrides, oxides, silicides, and graphene/carbon-matrix reinforcements for TMCs are broadly adopted. Powder metallurgy (PM) is a widely used method for the production of TMCs. This study reviews the common particles that are used as reinforcements in TMCs, their properties, production, the PM techniques used for consolidating them in TMCs, and their effect on the TMCs produced. Current literature and developments in TMCs have also been considered in this review.
- Open Access
- 2 April 2023
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 13 (2) , 10407-10413
The Effect of Cavitation Water Jet Shock as a Newly Technology on Micro-Forming Process
This article proposes a novel technology called water jet cavitation shock micro-forming to fabricate micro-features on 304 stainless steel foils with a thickness of 100µm, using a cavitation nozzle with an incident pressure of 8 to 20MPa. This study investigated the surface morphology of the formed part, the influence of incident pressure, target distance, and impact time on the forming depth, and analyzed the punching phenomenon of the formed components. The experimental results after the water jet cavitation shocking indicated that the surface morphology of the formed part of the 304 stainless foil sample had good quality and no conventional defects such as die scratches and cracks. Furthermore, when the incident pressure was 20MPa, the height of the uniform-shaped spherical cap exceeded 262µm. The forming depth increased with increasing incident pressure and impact time. Under an incident pressure of 20MPa, with the increase of target distance, the average depth of the formed part increased at first and then decreased. Finally, the analysis of the blanking phenomenon indicated that when the incident pressure increased to 30MPa, the workpiece was completely blanked. This is mainly because, under this incident pressure, the shockwave pressure generated by the collapse of the bubble deforms the workpiece beyond the stress limit of the material itself.
- 2 April 2023
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 13 (2) , 10407-10413
Open AccessThe Effect of Cavitation Water Jet Shock as a Newly Technology on Micro-Forming Process
This article proposes a novel technology called water jet cavitation shock micro-forming to fabricate micro-features on 304 stainless steel foils with a thickness of 100µm, using a cavitation nozzle with an incident pressure of 8 to 20MPa. This study investigated the surface morphology of the formed part, the influence of incident pressure, target distance, and impact time on the forming depth, and analyzed the punching phenomenon of the formed components. The experimental results after the water jet cavitation shocking indicated that the surface morphology of the formed part of the 304 stainless foil sample had good quality and no conventional defects such as die scratches and cracks. Furthermore, when the incident pressure was 20MPa, the height of the uniform-shaped spherical cap exceeded 262µm. The forming depth increased with increasing incident pressure and impact time. Under an incident pressure of 20MPa, with the increase of target distance, the average depth of the formed part increased at first and then decreased. Finally, the analysis of the blanking phenomenon indicated that when the incident pressure increased to 30MPa, the workpiece was completely blanked. This is mainly because, under this incident pressure, the shockwave pressure generated by the collapse of the bubble deforms the workpiece beyond the stress limit of the material itself.
- 26 September 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 237 (4) , 859-866
Oxidation performance of particle-reinforced Ti750 matrix composites
This study used SiCp, SiCw, B4C, and GPLs as reinforcements for Ti750 matrix alloy and composites synthesized by spark plasma sintering. The oxidation performances of the composites were then evaluated at 800 °C. 5 vol.% SiCp reinforced Ti750 composite recorded the least oxidation weight gain of 3.80 mg.cm−2, about 41.8% of the base alloy. The average oxidation rates K + of the five materials at 800 °C were less than 1 g.m−2.h−1, indicating all materials were within the anti-oxidation grade with excellent anti-oxidation performance. The oxidation products of the samples contained TiO2, Al2O3, and SiO2. 5 vol.% SiCp reinforced Ti750 composite had significantly flatter and denser oxide film, which was well bonded with the matrix thus having a better protective effect than the matrix material. With the addition of SiCp, the thickness of the oxide film decreased, and the resistance of the material significantly improved its high-temperature oxidation performance.
- 26 September 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 237 (4) , 859-866
Oxidation performance of particle-reinforced Ti750 matrix composites
This study used SiCp, SiCw, B4C, and GPLs as reinforcements for Ti750 matrix alloy and composites synthesized by spark plasma sintering. The oxidation performances of the composites were then evaluated at 800 °C. 5 vol.% SiCp reinforced Ti750 composite recorded the least oxidation weight gain of 3.80 mg.cm−2, about 41.8% of the base alloy. The average oxidation rates K + of the five materials at 800 °C were less than 1 g.m−2.h−1, indicating all materials were within the anti-oxidation grade with excellent anti-oxidation performance. The oxidation products of the samples contained TiO2, Al2O3, and SiO2. 5 vol.% SiCp reinforced Ti750 composite had significantly flatter and denser oxide film, which was well bonded with the matrix thus having a better protective effect than the matrix material. With the addition of SiCp, the thickness of the oxide film decreased, and the resistance of the material significantly improved its high-temperature oxidation performance.
- Open Access
- 1 December 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 1265g4
Effect of solid solution heat treatment following age hardening on microstructure and mechanical properties of 7000 series power aluminum alloy
In this paper, Al-11.1Zn-2.7Mg-1.7Cu-1.4Ti-0.2Zr alloy material was prepared by powder metallurgy to study the effect of the different solid-solution aging systems on the microstructure and mechanical properties of this 7000 series aluminum alloy. The microstructure of the alloy under the three different solid-solution processes S1, S2, and S3 were observed using an optical microscope, scanning electron microscope, and X-ray diffraction analysis. The mechanical properties were tested to determine the best solid-solution process. The results show that under the S2 solid-solution process, the alloy has the best mechanical properties, with a compressive strength of 646.7(±6.5) MPa and a fracture strain of 5.9(±0.06)%. The maximum hardness trends in the three solid-solution processes after aging are S2>S3>S1. The maximum hardness 220.7(±5.5 )HV occurs after S2 solid-solution and 121℃×18 h aging. Moreover, after S2 solid-solution treatment, the solid-solution degree is close to saturation, the solid-solution strengthening effect is the best, and dislocations contribute the most to the strength.
- 1 December 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 1265g4
Open AccessEffect of solid solution heat treatment following age hardening on microstructure and mechanical properties of 7000 series power aluminum alloy
In this paper, Al-11.1Zn-2.7Mg-1.7Cu-1.4Ti-0.2Zr alloy material was prepared by powder metallurgy to study the effect of the different solid-solution aging systems on the microstructure and mechanical properties of this 7000 series aluminum alloy. The microstructure of the alloy under the three different solid-solution processes S1, S2, and S3 were observed using an optical microscope, scanning electron microscope, and X-ray diffraction analysis. The mechanical properties were tested to determine the best solid-solution process. The results show that under the S2 solid-solution process, the alloy has the best mechanical properties, with a compressive strength of 646.7(±6.5) MPa and a fracture strain of 5.9(±0.06)%. The maximum hardness trends in the three solid-solution processes after aging are S2>S3>S1. The maximum hardness 220.7(±5.5 )HV occurs after S2 solid-solution and 121℃×18 h aging. Moreover, after S2 solid-solution treatment, the solid-solution degree is close to saturation, the solid-solution strengthening effect is the best, and dislocations contribute the most to the strength.
- Open Access
- 1 December 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 1265b7
Effect of La2O3 on resistance to high-temperature oxidation and corrosion of aluminized and aluminum-chrome coating
- 1 December 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 1265b7
Open AccessEffect of La2O3 on resistance to high-temperature oxidation and corrosion of aluminized and aluminum-chrome coating
- 25 November 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126597
Effect of SiCw volume fraction and cold pressure on microstructure and mechanical properties of aluminum matrix composites
The alloy powder and SiCw reinforcement were ball milled, cold-pressed, sintered, hot extruded and solution aged to obtain excellent mechanical properties such as hardness and compressive strength. The microstructure and properties of the material were characterized by metallographic microscope, scanning electron microscope (SEM), EDS, X-ray diffraction (XRD), HV-1000 microhardness and 7051 eddy current conductivity. The results show that the distribution of SiC whiskers in the mixed powder is relatively uniform, but there is still a small amount of agglomeration phenomenon in the sintered sample. The optimum cold pressure is 740 MPa. With the increase in SiCw content, the hardness, dislocation density and compressive strength of aluminum matrix composites are improved. The compressive strength of 5%SiCw reinforced aluminum matrix composite is 658.9 MPa and the elongation is 6.7%.
- 25 November 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126597
Effect of SiCw volume fraction and cold pressure on microstructure and mechanical properties of aluminum matrix composites
The alloy powder and SiCw reinforcement were ball milled, cold-pressed, sintered, hot extruded and solution aged to obtain excellent mechanical properties such as hardness and compressive strength. The microstructure and properties of the material were characterized by metallographic microscope, scanning electron microscope (SEM), EDS, X-ray diffraction (XRD), HV-1000 microhardness and 7051 eddy current conductivity. The results show that the distribution of SiC whiskers in the mixed powder is relatively uniform, but there is still a small amount of agglomeration phenomenon in the sintered sample. The optimum cold pressure is 740 MPa. With the increase in SiCw content, the hardness, dislocation density and compressive strength of aluminum matrix composites are improved. The compressive strength of 5%SiCw reinforced aluminum matrix composite is 658.9 MPa and the elongation is 6.7%.
- 17 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126510
Hot corrosion resistance of a Ti–Mo–Nb–Al–Si titanium matrix composites reinforced with in-situ TiC prepared by powder metallurgy
A mixture of the Ti-Mo-Nb-Al-Si matrix powder and Carbon nanotubes (CNTs) particles were used as the raw powder to produce the in-situ TiC reinforced titanium matrix composites (TMCs) via powder metallurgy. The effects of various contents of CNTs on the microstructure, phase composition and hot corrosion behavior of the composites were investigated. The results show that the corrosion mass gain of the composites with CNTs content of 1.0 wt.% was the minimum (18.73 mgcm-2), which was about 44.4% lighter than that of the matrix (33.70 mgcm-2). XRD results show that the corrosion phases were mainly composed of TiO2, Al2O3, SiO2, Ti(SO4)2, NaTiO2 and TiS. According to the SEM results, the grain size of the as-sintered composites can be refined by adding CNTs. With the increase of CNTs content, the grain size became smaller and smaller. The cross-sectional morphology shows that the oxide layer of the composites with 1.0 wt.% CNTs after corrosion was denser and thinner (21.44 μm). It was about 82.13% thinner than the oxide layer of the matrix (120.00 μm). All the results show that the TMCs with 1.0 wt.% CNTs have better hot corrosion resistance.
- 17 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (12) , 126510
Hot corrosion resistance of a Ti–Mo–Nb–Al–Si titanium matrix composites reinforced with in-situ TiC prepared by powder metallurgy
A mixture of the Ti-Mo-Nb-Al-Si matrix powder and Carbon nanotubes (CNTs) particles were used as the raw powder to produce the in-situ TiC reinforced titanium matrix composites (TMCs) via powder metallurgy. The effects of various contents of CNTs on the microstructure, phase composition and hot corrosion behavior of the composites were investigated. The results show that the corrosion mass gain of the composites with CNTs content of 1.0 wt.% was the minimum (18.73 mgcm-2), which was about 44.4% lighter than that of the matrix (33.70 mgcm-2). XRD results show that the corrosion phases were mainly composed of TiO2, Al2O3, SiO2, Ti(SO4)2, NaTiO2 and TiS. According to the SEM results, the grain size of the as-sintered composites can be refined by adding CNTs. With the increase of CNTs content, the grain size became smaller and smaller. The cross-sectional morphology shows that the oxide layer of the composites with 1.0 wt.% CNTs after corrosion was denser and thinner (21.44 μm). It was about 82.13% thinner than the oxide layer of the matrix (120.00 μm). All the results show that the TMCs with 1.0 wt.% CNTs have better hot corrosion resistance.
- 4 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 1065b3
Microstructure and properties of Ti-Al-Sn-Zr-Nb-Si matrix composite reinforced with in-situ TiC and Ti5Si3 prepared by powder metallurgy
- 4 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 1065b3
Microstructure and properties of Ti-Al-Sn-Zr-Nb-Si matrix composite reinforced with in-situ TiC and Ti5Si3 prepared by powder metallurgy
- 21 August 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 106559
Anisotropy of microstructure and properties of Al-10.22 Zn-2.87 Mg-1.2 Cu-0.213 Zr alloy
- 21 August 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 106559
Anisotropy of microstructure and properties of Al-10.22 Zn-2.87 Mg-1.2 Cu-0.213 Zr alloy
- 19 July 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (9) , 096582
Effect of surface boroaluminizing on thermal corrosion behavior of TC4 (Ti-6AL-4V) titanium alloy
- 19 July 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (9) , 096582
Effect of surface boroaluminizing on thermal corrosion behavior of TC4 (Ti-6AL-4V) titanium alloy