IEIgnaz Eisele

Ignaz Eisele

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ignaz Eisele has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Wafer-Scale Electrical Characterization of Al/AlxOy/Al Tunnel Junctions for Process Monitoring at Room Temperature

    by Simon Johann Klaus Lang, Ignaz Eisele, Johannes Weber, Alexandra Schewski, Emir Music, Alwin Maiwald, Martin Hahn, Daniela Zahn, Zhen Luo, Lars Nebrich, et al.

    Josephson junctions are key elements in superconducting qubits. Their efficient wafer-scale characterization is crucial for process control and optimization, motivating analysis approaches that extend beyond conventional cryogenic measurements. In this work, we demonstrate that room temperature (RT) capacitance and current–voltage measurements, combined with appropriate data analysis, enable extraction of relevant junction parameters such as oxide thickness, tunnel coefficient, and interfacial defect density. Furthermore, different charge transport mechanisms can be identified from detailed current–voltage analysis. We evaluate our characterization technique using tunnel junctions fabricated on 200 mm wafers in a complementary metal–oxide–semiconductor (CMOS)-compatible subtractive process. The results show a homogeneous average oxide thickness across the wafer with a variation below 3%. A dependence of the tunnel coefficient on oxide thickness indicates a stoichiometry gradient within the oxide. Additionally, low interfacial defect densities in the range of 70–5000 defects/cm2 are observed in our junctions, increasing with decreasing oxide thickness, suggesting that wet etching used for thickness control introduces interfacial trap states. Our study highlights the importance of advanced RT characterization for extracting tunnel junction parameters on the wafer scale, enabling effective process monitoring and optimization in industrial superconducting qubit manufacturing.

  • Open Access

    Defect characterization of unannealed neutron transmutation doped silicon by means of deep temperature microwave detected photo induced current transient spectroscopy

    by C. R. Engst, I. Eisele, C. Kutter

    Unannealed neutron transmutation doped silicon substrates with a target resistivity of approximately 1000 Ω cm are characterized for radiation induced defects by means of microwave detected photoinduced current transient spectroscopy (MD-PICTS). This technique is a contactless advancement of conventional PICTS and does not require the fabrication of ohmic contacts. Defect spectroscopy by means of MD-PICTS is conducted in a broad temperature range between 30 K and 293 K, which makes it possible to identify energetically shallow as well as deep traps. In addition, a wavelength dependent analysis is performed to determine whether a defect is located at the surface or in the bulk material. Three traps with an average activation energy of 68 meV , 85 meV , and 150 meV are observed. In addition, an indication for deep defect states with activation energies between 320 meV and 480 meV is found. According to the wavelength dependent analysis, it is assumed that all observed traps are bulk defects. Finally, a minority carrier lifetime of approximately 0.7 μs is determined, suggesting that the crystal is heavily damaged by neutron radiation.


  • Open Access

    Towards Low Cost and Low Temperature Capacitive CO2 Sensors Based on Amine Functionalized Silica Nanoparticles

    by Jamila Boudaden, Armin Klumpp, Hanns-Erik Endres, Ignaz Eisele

    Hybrid materials based on inorganic particles and an organic polymer were developed and used as an efficient sensing material for carbon dioxide (CO2). The sensing material consists of fumed silica that is functionalized with an organic polymer, polyethylenimine, by means of the impregnation method. The organic polymer is effectively immobilized around the silica nanoparticles and confirmed by infrared spectroscopy. Thermogravimetric analysis proves the thermal stability of the sensing material. CO2 capacitive sensors operating at temperatures lower than 70 °C were fabricated by depositing a thin layer of hybrid sensing material on interdigitated gold electrodes. Impedance spectroscopy explored the sensing capability of the hybrid organic–inorganic material towards CO2 in the presence of different relative humidity levels, as well as its stability and reversibility. This strategy to couple organic and inorganic materials as a sensing layer for CO2 paves the way for the design of a low-cost CO2 sensor.


  • Open Access

    Minority Carrier Lifetime Measurements for Contactless Oxidation Process Characterization and Furnace Profiling

    by Christian Bscheid, Christian R. Engst, Ignaz Eisele, Christoph Kutter

    Contactless minority carrier lifetime (lifetime) measurements by means of microwave detected photoconductivity are employed for oxidation process characterization and furnace profiling. Characterization is performed on oxidized float zone substrates with high resistivity and outstanding bulk quality, suggesting that the measured effective lifetime is strongly dominated by interface recombination and therefore reflects the oxide quality. The applied approach requires neither test structures nor time consuming measurements and is therefore of particular interest if high throughput is required. The method is used to investigate the impact of oxidation furnace leakage as well as to analyze the oxidation homogeneity across a horizontal oxidation furnace. For comparison, capacitance-voltage measurements are conducted to characterize the oxide properties. It is found that any type of furnace leakage, which induces fixed oxide charges as well as interface states, has a heavy impact on the measured effective lifetime, especially on the shape of generation rate dependent lifetime curves. Furthermore, a distinct lifetime decrease towards the tube door of the oxidation furnace could be observed. The latter is even detectable in an ideal oxidation process, generating high quality oxides. Besides plain equipment characterization, the presented approach is suitable to optimize the oxidation process itself regarding different parameters like temperature, gas flow, pressure, or process time.


  • Open Access

    An Approach to Reduce Greenhouse Gases in the Semiconductor Industry Using F2 Dissociated in Plasma for CVD Chamber Cleaning

    by Jamila Boudaden, Stephan Altmannshofer, Robert Wieland, Michael Pittroff, Ignaz Eisele

    The gases used in industrial cleaning processes are considered greenhouse gases with a high global warming potential (GWP). It is important to provide a viable alternative chemical vapor deposition (CVD) cleaning gas that is capable of removing efficiently deposited layers on the CVD chamber inner wall and other parts of the apparatus. The cleaning gas has to be environmental friendly in order to avoid accentuation of the global warming phenomena. Besides that, the alternative cleaning gas should be compatible with the existing gas delivery system and the CVD equipment that is already used by industrial companies. Only by fulfilling the three requirements mentioned above is it possible to replace the well-established cleaning gases. In this project, an F2–gas mixture for the in-situ cleaning of CVD chambers has been studied and compared with conventional cleaning methods. The conventional cleaning process is defined as a cleaning procedure using either C2F6 in RF plasma discharge or NF3 in remote plasma discharge.


  • Top Cited Papers
    Open Access

    Polyimide-Based Capacitive Humidity Sensor

    by Jamila Boudaden, Matthias Steinmaßl, Hanns-Erik Endres, Andreas Drost, Ignaz Eisele, Christoph Kutter, Peter Müller-Buschbaum

    The development of humidity sensors with simple transduction principles attracts considerable interest by both scientific researchers and industrial companies. Capacitive humidity sensors, based on polyimide sensing material with different thickness and surface morphologies, are prepared. The surface morphology of the sensing layer is varied from flat to rough and then to nanostructure called nanograss by using an oxygen plasma etch process. The relative humidity (RH) sensor selectively responds to the presence of water vapor by a capacitance change. The interaction between polyimide and water molecules is studied by FTIR spectroscopy. The complete characterization of the prepared capacitive humidity sensor performance is realized using a gas mixing setup and an evaluation kit. A linear correlation is found between the measured capacitance and the RH level in the range of 5 to 85%. The morphology of the humidity sensing layer is revealed as an important parameter influencing the sensor performance. It is proved that a nanograss-like structure is the most effective for detecting RH, due to its rapid response and recovery times, which are comparable to or even better than the ones of commercial polymer-based sensors. This work demonstrates the readiness of the developed RH sensor technology for industrialization.


  • Open Access

    Capacitive CO2 Sensor

    by Jamila Boudaden, Armin Klumpp, Hanns-Erik Endres, Ignaz Eisele

    The objective of the present paper is to provide a concept for a chemical sensor having a small size, a low power consumption and a high reliability for sensing CO2 under different humidity levels at atmospheric pressure, while maintaining a long term stability under working conditions. A high temperature regeneration process of the sensing layer is unneeded to ensure a long term stability of the sensing material. This objective is achieved by using a hybrid organic-inorganic nanomaterial, consisting of inorganic nanoparticles functionalized with an amine-based polymer.