Aixiang Wu
Aixiang Wu has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
Fei Jin
School of Civil and Resource Engineering
3 shared publications- Yong Wang
School of Civil and Resource Engineering, University of Science and Technology Beijing, Beijing 100083, China
3 shared publications - Zhuen Ruan
School of Civil and Resources Engineering, University of Science and Technology Beijing, Beijing 100083, China
3 shared publications Lianfu Zhang
School of Civil and Resource Engineering, University of Science and Technology Beijing, Beijing 100083, China
2 shared publicationsBin Li
School of Civil and Resource Engineering
1 shared publication- Chaoqun Dai
School of Civil and Resource Engineering
1 shared publication
Latest Publications
- 9 January 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 84, 108481
Early mechanical strength, hydration mechanism and leaching behavior of alkali-activated slag/fly ash paste filling materials
- 9 January 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 84, 108481
Early mechanical strength, hydration mechanism and leaching behavior of alkali-activated slag/fly ash paste filling materials
- Open Access
- 15 December 2023
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 20, e02792
Effect of particle size distribution of tailings on pressure gradient and drag reduction characteristics of non-cemented paste considering wall slip
- 15 December 2023
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 20, e02792
Open AccessEffect of particle size distribution of tailings on pressure gradient and drag reduction characteristics of non-cemented paste considering wall slip
- Open Access
- 8 September 2019
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2019, 1-9
Mechanical Properties of Paste Slurry under Constant Shear Rate in Initial Structure Failure Process
At constant shear rate, the process of deformation of the paste slurry is divided into two stages: one is the initial structural failure process with increasing shear stress; the other is the thixotropic process with decreasing shear stress after yielding. Based on experiments, the mechanical response characteristics of the paste slurry in the initial structural failure process under different shear rate conditions were studied in this paper. At the same time, according to the Maxwell model, the stress-time model equation describing the initial structure failure stage of the paste was deduced and the constant shearing test was carried out on the paste slurry at different mass concentrations; the model equation was used to fit the test data of the initial stress increment stage. The results showed that the model equation had higher prediction accuracy and better popularity. In the initial structural failure stage, the paste had a nonlinear stress-time relationship. At different shear rates (0.05, 0.5, and 1 s−1), the lower the rotation speed, the smoother the curve, and the slurry at various stages in the yielding process could be more clearly reflected; in the range of low constant shear rate (0.03, 0.05, and 0.07 s−1), the initial stress and yield stress of the paste increased with the increase of shear rate at the same mass concentration, and the time to yield was shorter. The yield stress increased exponentially with mass concentration.
- 8 September 2019
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2019, 1-9
Open AccessMechanical Properties of Paste Slurry under Constant Shear Rate in Initial Structure Failure Process
At constant shear rate, the process of deformation of the paste slurry is divided into two stages: one is the initial structural failure process with increasing shear stress; the other is the thixotropic process with decreasing shear stress after yielding. Based on experiments, the mechanical response characteristics of the paste slurry in the initial structural failure process under different shear rate conditions were studied in this paper. At the same time, according to the Maxwell model, the stress-time model equation describing the initial structure failure stage of the paste was deduced and the constant shearing test was carried out on the paste slurry at different mass concentrations; the model equation was used to fit the test data of the initial stress increment stage. The results showed that the model equation had higher prediction accuracy and better popularity. In the initial structural failure stage, the paste had a nonlinear stress-time relationship. At different shear rates (0.05, 0.5, and 1 s−1), the lower the rotation speed, the smoother the curve, and the slurry at various stages in the yielding process could be more clearly reflected; in the range of low constant shear rate (0.03, 0.05, and 0.07 s−1), the initial stress and yield stress of the paste increased with the increase of shear rate at the same mass concentration, and the time to yield was shorter. The yield stress increased exponentially with mass concentration.
- Open Access
- 22 January 2019
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2019 (1)
A Theoretical Model for the Rake Blockage Mitigation in Deep Cone Thickener: A Case Study of Lead‐Zinc Mine in China
Deep cone thickener (DCT) is key equipment in cemented paste backfill (CPB) technology. However, rake blockage occurs frequently in DCT during the dewatering process of the unclassified tailings being thickened from dilute slurry to thickened tailings or paste. Rake blockage has disastrous effects on the CPB operation. In order to investigate the influencing factors of rake blockage in DCT, a mathematical model of rake power in DCT was developed. In addition, stacking mud bed (made of thickened tailings) from the DCT in Huize lead‐zinc mine (HLZM) in different rake blockage accidents was sampled and tested to investigate the effect of tailings characters on rake blockage. Results indicated that the concentration of the mud bed and the friction between the mud bed and the cone wall contributed to the rake blockage. The concentration and friction were influenced by the high content of coarse particles in the mud bed. Moreover, activating devices for bed mud, as the corrective and preventive action, were developed to prevent the rake blockage, which was valid in HLZM.
- 22 January 2019
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2019 (1)
Open AccessA Theoretical Model for the Rake Blockage Mitigation in Deep Cone Thickener: A Case Study of Lead‐Zinc Mine in China
Deep cone thickener (DCT) is key equipment in cemented paste backfill (CPB) technology. However, rake blockage occurs frequently in DCT during the dewatering process of the unclassified tailings being thickened from dilute slurry to thickened tailings or paste. Rake blockage has disastrous effects on the CPB operation. In order to investigate the influencing factors of rake blockage in DCT, a mathematical model of rake power in DCT was developed. In addition, stacking mud bed (made of thickened tailings) from the DCT in Huize lead‐zinc mine (HLZM) in different rake blockage accidents was sampled and tested to investigate the effect of tailings characters on rake blockage. Results indicated that the concentration of the mud bed and the friction between the mud bed and the cone wall contributed to the rake blockage. The concentration and friction were influenced by the high content of coarse particles in the mud bed. Moreover, activating devices for bed mud, as the corrective and preventive action, were developed to prevent the rake blockage, which was valid in HLZM.
- Open Access
- 1 January 2019
- Published by Australian Centre for Geomechanics
- p. 571-578
Friction losses of cemented unclassified iron tailings slurry based on full-scale pipe-loop test
Friction losses is a key parameter in the design of pipeline transportation in paste backfill. A full-scale pipeloop test was conducted in the JCHX Paste Backfilling laboratory to investigate the friction losses of cemented unclassified iron tailings slurry. Friction losses in upward sloping pipe, vertical downward pipe, vertical upward pipe, 90° long radius elbow, horizontal straight pipe and downward sloping pipe were tested simultaneously under different solid fractions. The results indicated that friction losses always increase with flow rate and solid fraction. Friction losses in the elbows are about 1.55–2.16 times that in the horizontal straight pipe, which is about 2.7–10.0 kPa·m-1. The pipe-loop test data can be used to analyse the rheological priorities of cemented unclassified tailings slurry. Based on the Buckingham rheological equation, an empirical formula for friction losses was established and applied to a pipe with the optimal diameter of DN 150 mm. It can be concluded that the full-scale pipe-loop test is an effective way to investigate friction losses and the economics of design pipeline transportation.
- 1 January 2019
- Published by Australian Centre for Geomechanics
- p. 571-578
Open AccessFriction losses of cemented unclassified iron tailings slurry based on full-scale pipe-loop test
Friction losses is a key parameter in the design of pipeline transportation in paste backfill. A full-scale pipeloop test was conducted in the JCHX Paste Backfilling laboratory to investigate the friction losses of cemented unclassified iron tailings slurry. Friction losses in upward sloping pipe, vertical downward pipe, vertical upward pipe, 90° long radius elbow, horizontal straight pipe and downward sloping pipe were tested simultaneously under different solid fractions. The results indicated that friction losses always increase with flow rate and solid fraction. Friction losses in the elbows are about 1.55–2.16 times that in the horizontal straight pipe, which is about 2.7–10.0 kPa·m-1. The pipe-loop test data can be used to analyse the rheological priorities of cemented unclassified tailings slurry. Based on the Buckingham rheological equation, an empirical formula for friction losses was established and applied to a pipe with the optimal diameter of DN 150 mm. It can be concluded that the full-scale pipe-loop test is an effective way to investigate friction losses and the economics of design pipeline transportation.
- Open Access
- 1 August 2018
- Published by Wiley in Journal of Chemistry
- Vol. 2018, 1-9
Investigation of the Sedimentation Property of Backfill Material on the Basis of Rheological Test: A Case Study of Iron Tailings
Sedimentation of filling materials could cause pipe blocking accident in mines. However, few quantitative characterization studies have investigated the sedimentation characteristics of filling materials. In this study, the sedimentation property of iron tailings with a cement-sand ratio of 1 : 4 and mass concentration of 73%∼82% was investigated based on rheology measurements. Results showed that shear stress increased as shear rate rose from 0 s−1to 120 s−1. The shear stress increased as the filling material concentration increased as well. However, when the shear rate was reversed from 120 s−1to 0 s−1, the shear stress presented an increase-constant-decrease change pattern as the mass concentration increases in the rheological curve. Accordingly, the sedimentation performance of iron tailings filling material was divided into three types: intense sedimentation (the ascending rheological curve) in the mass concentration range of 73%∼76%, slight sedimentation (the constant rheological curve) in the mass concentration range of 77%∼79%, and almost no sedimentation (the descending rheological curve) in the mass concentration range of 80%∼82%. The associated mechanism involving slurry mass concentration-rheological curves-sedimentation performance was illustrated. A correlation between the pipeline rheology and filling material sedimentation performance was established, which provides a practical guide to avoid pipeline blocking while transporting the filling material.
- 1 August 2018
- Published by Wiley in Journal of Chemistry
- Vol. 2018, 1-9
Open AccessInvestigation of the Sedimentation Property of Backfill Material on the Basis of Rheological Test: A Case Study of Iron Tailings
Sedimentation of filling materials could cause pipe blocking accident in mines. However, few quantitative characterization studies have investigated the sedimentation characteristics of filling materials. In this study, the sedimentation property of iron tailings with a cement-sand ratio of 1 : 4 and mass concentration of 73%∼82% was investigated based on rheology measurements. Results showed that shear stress increased as shear rate rose from 0 s−1to 120 s−1. The shear stress increased as the filling material concentration increased as well. However, when the shear rate was reversed from 120 s−1to 0 s−1, the shear stress presented an increase-constant-decrease change pattern as the mass concentration increases in the rheological curve. Accordingly, the sedimentation performance of iron tailings filling material was divided into three types: intense sedimentation (the ascending rheological curve) in the mass concentration range of 73%∼76%, slight sedimentation (the constant rheological curve) in the mass concentration range of 77%∼79%, and almost no sedimentation (the descending rheological curve) in the mass concentration range of 80%∼82%. The associated mechanism involving slurry mass concentration-rheological curves-sedimentation performance was illustrated. A correlation between the pipeline rheology and filling material sedimentation performance was established, which provides a practical guide to avoid pipeline blocking while transporting the filling material.
- Open Access
- 1 January 2018
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2018 (1)
Investigating the Effect of Solid Components on Yield Stress for Cemented Paste Backfill via Uniform Design
Cemented paste backfill (CPB) technology has been applied quite popular around the world. Yield stress is a key factor determining whether CPB could be transported. In order to reveal the effect of solid components on yield stress of CPB, a uniform design experimental program (four factors and six levels) was conducted to test the rheological property of a mine’s CPB. The tested four factors including mass fraction, cement versus other solids ratio, coarse tailings, and gravel contents were considered during the experiment design. Likewise, six experimental levels were given to each factor. Results of the test show that yield stress increased with the mass fraction and cement content. However, the trend reversed for the content of coarse tailings and gravel. Contribution of the four factors to yield stress in descending order is mass fraction > content of gravel > content of coarse tailings > cement versus other tailings ration. Effect of solid components on the yield stress of CPB is mainly due to the different flocculation structure inside the CPB. These various flow structures result in the different free‐water content of CPB, leading to a different yield stress value.
- 1 January 2018
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2018 (1)
Open AccessInvestigating the Effect of Solid Components on Yield Stress for Cemented Paste Backfill via Uniform Design
Cemented paste backfill (CPB) technology has been applied quite popular around the world. Yield stress is a key factor determining whether CPB could be transported. In order to reveal the effect of solid components on yield stress of CPB, a uniform design experimental program (four factors and six levels) was conducted to test the rheological property of a mine’s CPB. The tested four factors including mass fraction, cement versus other solids ratio, coarse tailings, and gravel contents were considered during the experiment design. Likewise, six experimental levels were given to each factor. Results of the test show that yield stress increased with the mass fraction and cement content. However, the trend reversed for the content of coarse tailings and gravel. Contribution of the four factors to yield stress in descending order is mass fraction > content of gravel > content of coarse tailings > cement versus other tailings ration. Effect of solid components on the yield stress of CPB is mainly due to the different flocculation structure inside the CPB. These various flow structures result in the different free‐water content of CPB, leading to a different yield stress value.
- 1 December 2017
- Published by Springer Nature in Journal of Central South University
- Vol. 24 (12) , 2924-2931
Pre-reinforcement grout in fractured rock masses and numerical simulation for optimizing shrinkage stoping configuration
- 1 December 2017
- Published by Springer Nature in Journal of Central South University
- Vol. 24 (12) , 2924-2931
Pre-reinforcement grout in fractured rock masses and numerical simulation for optimizing shrinkage stoping configuration