Madesh Soundarrajan
Research Subjects
Madesh Soundarrajan has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Rajasekaran Thanigaivelan
AKT Memorial College of Engineering and Technology, Índia
5 shared publications - Govindaswamy Shanmugam
Department of Mechanical Engineering, Muthayammal Engineering College (Autonomous), Rasipuram, Namakkal(Dt), Tamil Nadu, India
2 shared publications - Kumaar Jeevarathnam Ravi Kumar Vinod
Department of Mechanical Engineering, Dr. N. G. P. Institute of Technology, Coimbatore, 641048, India
2 shared publications Anadavel Balasubramaniam
Government College Engineering, India
1 shared publicationArul T. G.
St. Mary's Engineering College, India
1 shared publicationArul Thayammal Ganeshan
St Marys Engn Coll, Dept Mech Engn, Hyderabad 508284, Telangana, Pakistan
1 shared publication
Latest Publications
- Open Access
- 14 May 2026
- Published by Kaunas University of Technology (KTU) in Materials Science
Effect of IR Radiation on Drilling of Natural Fiber Mesh-reinforced Hybrid Epoxy Composites
Due to anisotropic performance of polymer matrix composites (PMC) drilling is a complex process in traditional drilling. Different type of fiber meshes and their resistance to infrared radiation (IR) on drilling operations are examined in this study. The natural and synthetic meshes are used to fabricate the composites, which are jute fiber mesh composite (JTMC), glass fiber mesh mixed composite (GLMC), nylon fiber mesh mixed composite (NLMC), cotton fiber mesh mixed composite (CTMC), and gunnet fiber mesh mixed composite (GNMC).In order to reveal the addition of heat on the machining characteristics of different composites, the Infrared (IR) radiations are used in the machining zone. The most important process parameters in the drilling process such as drilling speed in rpm, feed rate in mm/min and machining zone temperature in oC are considered for the experiment. Among the composites, GNMC shows the lowest delimitation Factor (DF) of 1.3 i.e 52.2 % which is less than JTMC for the parameter combination of 60 rpm, 12 mm/min and 40 oC. Also, the least surface roughness in Ra (SR) noted with the JTMC, which is 44.6 % lesser than GNMC at the same parameter combination. The infrared radiation heat affects the strands of fibers and its soft nature with the stiffness which contributes major role on surface roughness. The GLMC and CTMC are produces the next lesser DF when compared with the JTMC, which creates 4.95 and 5.68 DF, respectively. Furthermore, scanning electron microscope (SEM) figure studies are carried out on the circumference of drilled workpiece to distinguish the effect of heating and fibers impact on drilling quality.
- 14 May 2026
- Published by Kaunas University of Technology (KTU) in Materials Science
Open AccessEffect of IR Radiation on Drilling of Natural Fiber Mesh-reinforced Hybrid Epoxy Composites
Due to anisotropic performance of polymer matrix composites (PMC) drilling is a complex process in traditional drilling. Different type of fiber meshes and their resistance to infrared radiation (IR) on drilling operations are examined in this study. The natural and synthetic meshes are used to fabricate the composites, which are jute fiber mesh composite (JTMC), glass fiber mesh mixed composite (GLMC), nylon fiber mesh mixed composite (NLMC), cotton fiber mesh mixed composite (CTMC), and gunnet fiber mesh mixed composite (GNMC).In order to reveal the addition of heat on the machining characteristics of different composites, the Infrared (IR) radiations are used in the machining zone. The most important process parameters in the drilling process such as drilling speed in rpm, feed rate in mm/min and machining zone temperature in oC are considered for the experiment. Among the composites, GNMC shows the lowest delimitation Factor (DF) of 1.3 i.e 52.2 % which is less than JTMC for the parameter combination of 60 rpm, 12 mm/min and 40 oC. Also, the least surface roughness in Ra (SR) noted with the JTMC, which is 44.6 % lesser than GNMC at the same parameter combination. The infrared radiation heat affects the strands of fibers and its soft nature with the stiffness which contributes major role on surface roughness. The GLMC and CTMC are produces the next lesser DF when compared with the JTMC, which creates 4.95 and 5.68 DF, respectively. Furthermore, scanning electron microscope (SEM) figure studies are carried out on the circumference of drilled workpiece to distinguish the effect of heating and fibers impact on drilling quality.
- 1 April 2026
- Published by Springer Nature in Journal of Applied Electrochemistry
- Vol. 56 (5) , 91
Electrochemical micromachining of shape memory alloy: effect of polymer composite electrodes on micro-hole surface integrity
- 1 April 2026
- Published by Springer Nature in Journal of Applied Electrochemistry
- Vol. 56 (5) , 91
Electrochemical micromachining of shape memory alloy: effect of polymer composite electrodes on micro-hole surface integrity
- Open Access
- 1 January 2026
- Published by National Library of Serbia in Chemical Industry and Chemical Engineering Quarterly
- No. 00,p. 10
Effect of electrode hybridization in electrochemical micromachining of aluminum alloy composite
The need for micro-level components in aerospace, automotive, and medical fields has continuously risen in recent years. In electrochemical micromachining (ECMM), due to the presence of hard particles like aluminum scrap alloy, it is difficult to make micro holes in such materials, as most micro holes appear with high overcut (OC). Also considering the need for higher material removal rate (MRR) and improved accuracy in micro-component fabrication, work is planned on the type of tool electrode and its insulation. Hence, different tool electrodes, including ceramic composite tool (CRCT), rubber insulated tool (RUIT), rubber filled hollow tool (RFHT), and normal tool (NRMT), are used to address these challenges. The effects of key input parameters, including machining voltage, duty cycle, and electrolyte concentration, were systematically investigated. An experimental result indicates that RUIT achieves MRR 2.09 times higher than NRMT. Also, CRCT demonstrates higher MRR, which is 1.7 times better than NRMT under the selected parameter set of 23 g/L, 13 V, and 80% duty cycle. Among the different tools, RFHT produces the lowest OC of 58.56 μm. Additionally, to reveal the effect of tool electrode impact on machining outcome and metal surface nature, scanning electron microscope (SEM) image analysis is carried out.
- 1 January 2026
- Published by National Library of Serbia in Chemical Industry and Chemical Engineering Quarterly
- No. 00,p. 10
Open AccessEffect of electrode hybridization in electrochemical micromachining of aluminum alloy composite
The need for micro-level components in aerospace, automotive, and medical fields has continuously risen in recent years. In electrochemical micromachining (ECMM), due to the presence of hard particles like aluminum scrap alloy, it is difficult to make micro holes in such materials, as most micro holes appear with high overcut (OC). Also considering the need for higher material removal rate (MRR) and improved accuracy in micro-component fabrication, work is planned on the type of tool electrode and its insulation. Hence, different tool electrodes, including ceramic composite tool (CRCT), rubber insulated tool (RUIT), rubber filled hollow tool (RFHT), and normal tool (NRMT), are used to address these challenges. The effects of key input parameters, including machining voltage, duty cycle, and electrolyte concentration, were systematically investigated. An experimental result indicates that RUIT achieves MRR 2.09 times higher than NRMT. Also, CRCT demonstrates higher MRR, which is 1.7 times better than NRMT under the selected parameter set of 23 g/L, 13 V, and 80% duty cycle. Among the different tools, RFHT produces the lowest OC of 58.56 μm. Additionally, to reveal the effect of tool electrode impact on machining outcome and metal surface nature, scanning electron microscope (SEM) image analysis is carried out.
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 31, e20260121
Microstructural and mechanical characterization of gas tungsten arc welded 316L stainless steel joints: effects of Ni Cr W/B coated fillers
The present investigation aims to produce sound weld joints of 316L stainless steel (SS) using the gas tungsten arc welding (GTAW) process with different metal coated filler metals. The filler materials used in GTAW are coated with nickel (Ni), chromium (Cr) and Tungsten (W) / Boron (B) on SS 308L for welding process. The major process parameters of welding, welding current, arc voltage and filler wire diameter and arc length are considered. These coated filler metals were categorized based on the type of coating applied to SS 308L, namely Ni, Ni B, Cr B, Ni Cr B and Ni Cr W/B. Among different metal coatings, Ni Cr–B coated filler wire yielded the second highest tensile strength while the maximum tensile strength of 668 MPa obtained using the Ni Cr–W/B coated filler wire. Moreover, Ni Cr–W/B coated filler metal exhibited the highest impact toughness of 83.64 J which is 69% higher when compared to the plain Ni-coated filler metal. The average micro hardness of welds produced using the Ni Cr–W/B filler metal is approximately 10.08% higher than that of welds fabricated with the conventional Ni-coated filler. Scanning electron microscopy (SEM) used to examine the weldments and HAZ in order to evaluate the influence of various metal coatings on microstructural evolution.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 31, e20260121
Open AccessMicrostructural and mechanical characterization of gas tungsten arc welded 316L stainless steel joints: effects of Ni Cr W/B coated fillers
The present investigation aims to produce sound weld joints of 316L stainless steel (SS) using the gas tungsten arc welding (GTAW) process with different metal coated filler metals. The filler materials used in GTAW are coated with nickel (Ni), chromium (Cr) and Tungsten (W) / Boron (B) on SS 308L for welding process. The major process parameters of welding, welding current, arc voltage and filler wire diameter and arc length are considered. These coated filler metals were categorized based on the type of coating applied to SS 308L, namely Ni, Ni B, Cr B, Ni Cr B and Ni Cr W/B. Among different metal coatings, Ni Cr–B coated filler wire yielded the second highest tensile strength while the maximum tensile strength of 668 MPa obtained using the Ni Cr–W/B coated filler wire. Moreover, Ni Cr–W/B coated filler metal exhibited the highest impact toughness of 83.64 J which is 69% higher when compared to the plain Ni-coated filler metal. The average micro hardness of welds produced using the Ni Cr–W/B filler metal is approximately 10.08% higher than that of welds fabricated with the conventional Ni-coated filler. Scanning electron microscopy (SEM) used to examine the weldments and HAZ in order to evaluate the influence of various metal coatings on microstructural evolution.
- 23 April 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Effect of UV rays heating on the mechanical and drilling properties of epoxy hybrid composites: An investigation
This research investigates the optimization of natural fiber-reinforced polymer matrix composites (PMCs) for drilling applications, addressing the inherent anisotropy of these materials. A range of natural fibers, such as jute, banana, flax, kenaf, paddy straw, Grewia serrulatta, cotton, human hair, and sisal, were used to fabricate PMCs, and their mechanical properties (flexural and tensile strength) were assessed. To enhance mechanical stability, copper (Cu) particles were incorporated into all composites. Drilling experiments are designed using L16 Orthogonal Array, were performed with UV-assisted heating to study the effects of composite type, drilling speed, feed rate, and machining zone temperature on the drilling process. The drilling process parameters are optimized through Preference Ranking Organization Method for Enrichment Evaluations II (PROMETHEE II) technique. Among the use of different fibers, Grewia serrulatta produces the highest flexural and tensile strengths of 850 MPa and 550 MPa, respectively, than other fibers, as well as third and fourth highest flexural strength obtained with Flax and sisal Grewia fibers, respectively. The flax fiber produces 741 MPa flexural strength which is 58% higher than jute fiber, and Grewia fiber creates 650 MPa flexural strength which is 32.1% higher than the jute fiber strength. Based on PROMETHEE II, kenaf fiber composite, 25 rpm drilling speed, 70 mm/min flow rate and 40°C, is suggested obtaining the better quality hole. According to the analysis of variance of preferences values, type of composite and feed rate of drilling machine contribute the quality of hole around 51.65% and 15.80%, respectively. Furthermore, scanning electron microscope image studies are conducted on the exterior of drilled work piece to recognize the effect of heating and fibers impact on drilling quality.
- 23 April 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Effect of UV rays heating on the mechanical and drilling properties of epoxy hybrid composites: An investigation
This research investigates the optimization of natural fiber-reinforced polymer matrix composites (PMCs) for drilling applications, addressing the inherent anisotropy of these materials. A range of natural fibers, such as jute, banana, flax, kenaf, paddy straw, Grewia serrulatta, cotton, human hair, and sisal, were used to fabricate PMCs, and their mechanical properties (flexural and tensile strength) were assessed. To enhance mechanical stability, copper (Cu) particles were incorporated into all composites. Drilling experiments are designed using L16 Orthogonal Array, were performed with UV-assisted heating to study the effects of composite type, drilling speed, feed rate, and machining zone temperature on the drilling process. The drilling process parameters are optimized through Preference Ranking Organization Method for Enrichment Evaluations II (PROMETHEE II) technique. Among the use of different fibers, Grewia serrulatta produces the highest flexural and tensile strengths of 850 MPa and 550 MPa, respectively, than other fibers, as well as third and fourth highest flexural strength obtained with Flax and sisal Grewia fibers, respectively. The flax fiber produces 741 MPa flexural strength which is 58% higher than jute fiber, and Grewia fiber creates 650 MPa flexural strength which is 32.1% higher than the jute fiber strength. Based on PROMETHEE II, kenaf fiber composite, 25 rpm drilling speed, 70 mm/min flow rate and 40°C, is suggested obtaining the better quality hole. According to the analysis of variance of preferences values, type of composite and feed rate of drilling machine contribute the quality of hole around 51.65% and 15.80%, respectively. Furthermore, scanning electron microscope image studies are conducted on the exterior of drilled work piece to recognize the effect of heating and fibers impact on drilling quality.
- 1 May 2024
- Published by Pleiades Publishing Ltd in Russian Journal of Applied Chemistry
- Vol. 97 (5) , 463-475
Performance Investigation of Electrochemical Micro Machining Process Using Salt Free Composite Electrolytes
The micro holes produced using electrochemical micro machining (ECMM) process emphasis the accuracy and surface finish of micro hole due to its nature of machining. Hence, this paper attempt with different salt free electrolytes and its results are compared with normal electrolyte. The electrolyte such as sodium nitrate mixed electrolyte (SONE), copper mixed electrolyte (CUME), sulfuric acid mixed electrolyte (SFAE) and mixer of these entire materials in equal ratio considered as composite electrolyte (COME) are used for experiments. The optimization techniques such as Weighted Aggregated Sum Product Assessment (WASPAS) and Multi-Objective Optimization on the basis of Ratio Analysis (MOORA) are used to determine the best machining combination. The results obtained with experiments noted that maximum MRR, i.e., 1.8887 µm/s is obtained in COME with the parameter combination of 7 V machining voltage, 90% duty cycle and 38°C electrolyte temperature which is 98.23% higher than the SONE. Furthermore, field emission scanning electron micro scope (FESEM) image analysis and energy dispersive X-ray spectroscopy (EDX) are carried out on the micro holes to know the clarity over the effect of electrolyte on surface quality of micro hole.
- 1 May 2024
- Published by Pleiades Publishing Ltd in Russian Journal of Applied Chemistry
- Vol. 97 (5) , 463-475
Performance Investigation of Electrochemical Micro Machining Process Using Salt Free Composite Electrolytes
The micro holes produced using electrochemical micro machining (ECMM) process emphasis the accuracy and surface finish of micro hole due to its nature of machining. Hence, this paper attempt with different salt free electrolytes and its results are compared with normal electrolyte. The electrolyte such as sodium nitrate mixed electrolyte (SONE), copper mixed electrolyte (CUME), sulfuric acid mixed electrolyte (SFAE) and mixer of these entire materials in equal ratio considered as composite electrolyte (COME) are used for experiments. The optimization techniques such as Weighted Aggregated Sum Product Assessment (WASPAS) and Multi-Objective Optimization on the basis of Ratio Analysis (MOORA) are used to determine the best machining combination. The results obtained with experiments noted that maximum MRR, i.e., 1.8887 µm/s is obtained in COME with the parameter combination of 7 V machining voltage, 90% duty cycle and 38°C electrolyte temperature which is 98.23% higher than the SONE. Furthermore, field emission scanning electron micro scope (FESEM) image analysis and energy dispersive X-ray spectroscopy (EDX) are carried out on the micro holes to know the clarity over the effect of electrolyte on surface quality of micro hole.
- 28 March 2024
- Published by Chiang Mai University in Chiang Mai Journal of Science
- Vol. 51 (2) , 1-14
Study on Effect of Nickel Molybdenum Coated Filler in Gas Tungsten Arc Welding
Chiang Mai Journal of Science, Faculty of Science, Chiang Mai University
- 28 March 2024
- Published by Chiang Mai University in Chiang Mai Journal of Science
- Vol. 51 (2) , 1-14
Study on Effect of Nickel Molybdenum Coated Filler in Gas Tungsten Arc Welding
Chiang Mai Journal of Science, Faculty of Science, Chiang Mai University
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 29 (4) , e20240379
Effect of polymer based electrolytes on surface of integrity of micro holes using electrochemical micro machining process for scrapped aluminium alloy
The flexibility of Aluminium Metal Matrix Composite (AMMC) is enormous in all aspect of manufacturing and electrochemical micro machining (ECMM) is an increasingly prevalent method due to its no tool wear, high precision, burr-free machining surface and non-invasive machining surface for all kind of materials. Hence, this present work investigated the ECMM process with biocompatible polymer dissolution mediums for electrolyte and their results are compared with regular aqueous medium. The bio conjugate agents such as bio polymer hydrogel and ethylene glycol is employed as solid bio polymer electrolyte (SBPE) and ethylene glycol electrolyte (EGLE) respectively to machine micro-holes on the AMMC work material. The results are compared with regular aqueous sodium nitrate electrolyte (ASNE). The machining performances are estimated by means of material removal rate (MRR) and overcut (OC). The results predicted that MRR increases for SBPE and EGLE by 2.47 times and 2.09 times respectively for the parametric mixture of 9V, 31 g/l and 65% than ASNE. The analysis taken with the field emission scanning electron microscope (FESEM) to determine the effect of SBPE and EGLE on the surface topography and interior machined edges of a micro-hole.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 29 (4) , e20240379
Open AccessEffect of polymer based electrolytes on surface of integrity of micro holes using electrochemical micro machining process for scrapped aluminium alloy
The flexibility of Aluminium Metal Matrix Composite (AMMC) is enormous in all aspect of manufacturing and electrochemical micro machining (ECMM) is an increasingly prevalent method due to its no tool wear, high precision, burr-free machining surface and non-invasive machining surface for all kind of materials. Hence, this present work investigated the ECMM process with biocompatible polymer dissolution mediums for electrolyte and their results are compared with regular aqueous medium. The bio conjugate agents such as bio polymer hydrogel and ethylene glycol is employed as solid bio polymer electrolyte (SBPE) and ethylene glycol electrolyte (EGLE) respectively to machine micro-holes on the AMMC work material. The results are compared with regular aqueous sodium nitrate electrolyte (ASNE). The machining performances are estimated by means of material removal rate (MRR) and overcut (OC). The results predicted that MRR increases for SBPE and EGLE by 2.47 times and 2.09 times respectively for the parametric mixture of 9V, 31 g/l and 65% than ASNE. The analysis taken with the field emission scanning electron microscope (FESEM) to determine the effect of SBPE and EGLE on the surface topography and interior machined edges of a micro-hole.
- 27 January 2022
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 37 (13) , 1526-1539
A performance study of electrochemical micro-machining on SS 316L using suspended copper metal powder along with stirring effect
Electrochemical micro-machining (ECMM) is widely used for machining small-sized components, intricate shapes, and hard materials. Fabrication of micro-holes in stainless steel 316L (SS 316L) can be effortlessly achieved by the ECMM process rather than other machining methods, owing to its favorable machining characteristics and advantages. This paper tries to elucidate the performance of ECMM on the machining of SS 316L using an eco-friendly citric acid as an electrolyte medium, and the results are compared with copper metal powder suspended in a citric acid electrolyte (suspended electrolyte) and copper metal powder suspended in a citric acid electrolyte with the assistance of a mechanical overhead stirrer (suspended electrolyte with stirrer effect). The output performance parameters such as MRR and overcut are calculated by varying the input response parameters such as machining voltage, duty cycle, and electrolyte concentration. From the experimental results at higher parameter levels, the highest MRR and moderate overcut are obtained for suspended electrolyte with stirrer effect. For suspended electrolyte, moderate MRR and the highest overcut are detected. The least MRR and reduced overcut are found for citric acid electrolyte. SEM and EDAX analysis have been carried out to see the machined micro-hole and the composition present in the specimen.
- 27 January 2022
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 37 (13) , 1526-1539
A performance study of electrochemical micro-machining on SS 316L using suspended copper metal powder along with stirring effect
Electrochemical micro-machining (ECMM) is widely used for machining small-sized components, intricate shapes, and hard materials. Fabrication of micro-holes in stainless steel 316L (SS 316L) can be effortlessly achieved by the ECMM process rather than other machining methods, owing to its favorable machining characteristics and advantages. This paper tries to elucidate the performance of ECMM on the machining of SS 316L using an eco-friendly citric acid as an electrolyte medium, and the results are compared with copper metal powder suspended in a citric acid electrolyte (suspended electrolyte) and copper metal powder suspended in a citric acid electrolyte with the assistance of a mechanical overhead stirrer (suspended electrolyte with stirrer effect). The output performance parameters such as MRR and overcut are calculated by varying the input response parameters such as machining voltage, duty cycle, and electrolyte concentration. From the experimental results at higher parameter levels, the highest MRR and moderate overcut are obtained for suspended electrolyte with stirrer effect. For suspended electrolyte, moderate MRR and the highest overcut are detected. The least MRR and reduced overcut are found for citric acid electrolyte. SEM and EDAX analysis have been carried out to see the machined micro-hole and the composition present in the specimen.
- Open Access
- 1 January 2022
- Published by National Library of Serbia in Chemical Industry and Chemical Engineering Quarterly
- Vol. 28 (4) , 329-337
Effect of different electrolytes on electrochemical micro-machining of SS 316L
The use of stainless steel 316L (SS 316L) in industries such as medical, marine, aerospace, bio-medical, and automobile sectors is increasing rapidly. Electrochemical micro-machining (ECMM) is the apt method for machining SS 316L due to its burr-free machining surface, no residual stress, and high precision. However, there are some limitations found in the usage of strong electrolytes such as HCl, H2SO4, KOH, NaNO3, and NaCl, which are reportedly facing difficulties in disposing it to the environment and handling issues. Hence, this paper addresses to overcome the disadvantages faced in ECMM process when using strong electrolytes to machine SS 316L, so therefore different organic electrolytes such as tartaric acid (C4H6O6), citric acid (C6H8O7), and a combination of tartaric and citric acid electrolyte (mixed electrolyte) are considered to select the best electrolyte. Process parameters like machining voltage, duty cycle, and electrolyte concentration are included in determining the performance of machining. The performance of ECMM is evaluated using material removal rate (MRR) and overcut. The overcut of tartaric acid electrolyte is found to be 179% less than mixed electrolyte for the parameter combination of 12 g/l, 11 V, and 85%. The mixed electrolyte shows 114.2% higher MRR than the tartaric acid electrolyte for the parameter solutions of 25%, 11 V, and 20 g/l. Furthermore, the citric acid electrolyte shows the second lowest overcut and higher MRR in all aspects of machining performance. Field emission scanning electron microscope (FESEM) studies are carried out to realise the effect of electrolyte on the machining surface.
- 1 January 2022
- Published by National Library of Serbia in Chemical Industry and Chemical Engineering Quarterly
- Vol. 28 (4) , 329-337
Open AccessEffect of different electrolytes on electrochemical micro-machining of SS 316L
The use of stainless steel 316L (SS 316L) in industries such as medical, marine, aerospace, bio-medical, and automobile sectors is increasing rapidly. Electrochemical micro-machining (ECMM) is the apt method for machining SS 316L due to its burr-free machining surface, no residual stress, and high precision. However, there are some limitations found in the usage of strong electrolytes such as HCl, H2SO4, KOH, NaNO3, and NaCl, which are reportedly facing difficulties in disposing it to the environment and handling issues. Hence, this paper addresses to overcome the disadvantages faced in ECMM process when using strong electrolytes to machine SS 316L, so therefore different organic electrolytes such as tartaric acid (C4H6O6), citric acid (C6H8O7), and a combination of tartaric and citric acid electrolyte (mixed electrolyte) are considered to select the best electrolyte. Process parameters like machining voltage, duty cycle, and electrolyte concentration are included in determining the performance of machining. The performance of ECMM is evaluated using material removal rate (MRR) and overcut. The overcut of tartaric acid electrolyte is found to be 179% less than mixed electrolyte for the parameter combination of 12 g/l, 11 V, and 85%. The mixed electrolyte shows 114.2% higher MRR than the tartaric acid electrolyte for the parameter solutions of 25%, 11 V, and 20 g/l. Furthermore, the citric acid electrolyte shows the second lowest overcut and higher MRR in all aspects of machining performance. Field emission scanning electron microscope (FESEM) studies are carried out to realise the effect of electrolyte on the machining surface.