Rajasekaran Thanigaivelan
Research Subjects
Research Interests
Rajasekaran Thanigaivelan has a total of 100 co-authors. Here are the top co-authors by number of shared publications:
- Ramanathan Arunachalam
Sultan Qaboos University, Al Khoudh, Oman
7 shared publications - Madesh Soundarrajan
Muthayammal Engineering College, India
5 shared publications - Nadanasabapathi Sivashankar
Department of Mechanical Engineering, Kongunadu College of Engineering and Technology (Autonomous), Thottiam, Trichy (Dt), Tamil Nadu, India
5 shared publications - Jagadeesha Thimmaiaha
Department of Mechanical Engineering, National Institute of Technology, Kozhikode, India
4 shared publications - Kumaar Jeevarathnam Ravi Kumar Vinod
Department of Mechanical Engineering, Dr. N. G. P. Institute of Technology, Coimbatore, 641048, India
3 shared publications - Maniraj Sekar
Paavai Engineering College, India
3 shared publications
Latest Publications
- 3 August 2026
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 33 (25) , 12824-12835
Studies on sustainable masonry materials and the reuse of industrial by-products
- 3 August 2026
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 33 (25) , 12824-12835
Studies on sustainable masonry materials and the reuse of industrial by-products
- Open Access
- 1 January 2026
- Published by National Library of Serbia in Chemical Industry and Chemical Engineering Quarterly
- Vol. 32 (4) , 321-330
Electrochemical machining with ethylene glycol mixed electrolyte on Inconel 718
Electrochemical machining is a non-traditional machining process, especially for difficult-to-cut materials. An electrolyte was prepared with ethylene glycol (EG) 30 vol% and distilled water 70 vol% as a solution with the combination of \ce{NaNO3} , and stainless steel electrodes coated with polyvinyl acetate (PVA) and commercially available ceramic paste. Inconel 718 was used as a workpiece material in this study. L_9 orthogonal array (OA) experiments are conducted for both sodium nitrate ( \ce{NaNO3} ) and EG+ \ce{NaNO3} electrolyte. The process parameters are optimized using Preference Ranking Organisation Method of Enrichment Evaluation (PROMETHEE II) and Artificial Neural Network (ANN). According to the multi-criteria decision-making method, the optimal parameter combination of both electrolytes is stainless steel electrode at 9 V, 70% duty cycle, 28 \, g \cdot L^{-1} electrolyte concentration and ceramic coated electrode at 13 V, 80% duty cycle, 28 \, g \cdot L^{-1} electrolyte concentration. The results of PROMETHEE II were verified using the developed ANN architecture. ECM performance was significantly improved by adding EG to the sodium nitrate electrolyte. EG significantly improved the material removal efficiency by increasing the average machining rate (MR) by 69.70%. Concurrently, the diametral overcut (DOC) dropped by roughly 27.4%, indicating a significant improvement in dimensional accuracy. Only a slight rise of about 1.6% was seen in the surface corrosion factor (SCF), indicating that the addition of EG has no negative effects on surface integrity.
- 1 January 2026
- Published by National Library of Serbia in Chemical Industry and Chemical Engineering Quarterly
- Vol. 32 (4) , 321-330
Open AccessElectrochemical machining with ethylene glycol mixed electrolyte on Inconel 718
Electrochemical machining is a non-traditional machining process, especially for difficult-to-cut materials. An electrolyte was prepared with ethylene glycol (EG) 30 vol% and distilled water 70 vol% as a solution with the combination of \ce{NaNO3} , and stainless steel electrodes coated with polyvinyl acetate (PVA) and commercially available ceramic paste. Inconel 718 was used as a workpiece material in this study. L_9 orthogonal array (OA) experiments are conducted for both sodium nitrate ( \ce{NaNO3} ) and EG+ \ce{NaNO3} electrolyte. The process parameters are optimized using Preference Ranking Organisation Method of Enrichment Evaluation (PROMETHEE II) and Artificial Neural Network (ANN). According to the multi-criteria decision-making method, the optimal parameter combination of both electrolytes is stainless steel electrode at 9 V, 70% duty cycle, 28 \, g \cdot L^{-1} electrolyte concentration and ceramic coated electrode at 13 V, 80% duty cycle, 28 \, g \cdot L^{-1} electrolyte concentration. The results of PROMETHEE II were verified using the developed ANN architecture. ECM performance was significantly improved by adding EG to the sodium nitrate electrolyte. EG significantly improved the material removal efficiency by increasing the average machining rate (MR) by 69.70%. Concurrently, the diametral overcut (DOC) dropped by roughly 27.4%, indicating a significant improvement in dimensional accuracy. Only a slight rise of about 1.6% was seen in the surface corrosion factor (SCF), indicating that the addition of EG has no negative effects on surface integrity.
- Open Access
- 31 July 2025
- Published by International Association of Physical Chemists (IAPC) in Journal of Electrochemical Science and Engineering
- Vol. 15 (6) , 2821
Electrochemical micromachining of galvanized iron sheets: process optimization and performance evaluation
Electrochemical micromachining (ECMM) is a promising non-traditional technique for fabricating micro-features on conductive materials with high precision and minimal thermal effects. This study focuses on the ECMM of galvanized iron (GI) sheets using sodium nitrate (NaNO3) as the electrolyte. Key process parameters such as voltage, duty cycle, and electrolyte concentration were optimized to improve machining performance in terms of material removal rate (MRR) and overcut (OC). An L9 orthogonal array was used to design the experiments, and signal-to-noise ratio, along with analysis of variance (ANOVA), was employed to identify the most influential parameters. Results showed that voltage significantly influenced both MRR and OC, with optimal MRR observed at 12 V, 70 % duty cycle, and 20 g l-1 NaNO3 concentration. Conversely, the minimum OC was achieved at 6 V, 50 % duty cycle and 10 g l-1 NaNO3 electrolyte concentration. SEM analysis confirmed over-etched boundaries at higher voltage and well-defined micro-holes at lower voltage. This research demonstrates the critical role of parameter tuning in enhancing the quality and precision of ECMM on GI sheets.
- 31 July 2025
- Published by International Association of Physical Chemists (IAPC) in Journal of Electrochemical Science and Engineering
- Vol. 15 (6) , 2821
Open AccessElectrochemical micromachining of galvanized iron sheets: process optimization and performance evaluation
Electrochemical micromachining (ECMM) is a promising non-traditional technique for fabricating micro-features on conductive materials with high precision and minimal thermal effects. This study focuses on the ECMM of galvanized iron (GI) sheets using sodium nitrate (NaNO3) as the electrolyte. Key process parameters such as voltage, duty cycle, and electrolyte concentration were optimized to improve machining performance in terms of material removal rate (MRR) and overcut (OC). An L9 orthogonal array was used to design the experiments, and signal-to-noise ratio, along with analysis of variance (ANOVA), was employed to identify the most influential parameters. Results showed that voltage significantly influenced both MRR and OC, with optimal MRR observed at 12 V, 70 % duty cycle, and 20 g l-1 NaNO3 concentration. Conversely, the minimum OC was achieved at 6 V, 50 % duty cycle and 10 g l-1 NaNO3 electrolyte concentration. SEM analysis confirmed over-etched boundaries at higher voltage and well-defined micro-holes at lower voltage. This research demonstrates the critical role of parameter tuning in enhancing the quality and precision of ECMM on GI sheets.
- 7 April 2025
- Published by Springer Nature in Lasers in Manufacturing and Materials Processing
- Vol. 12 (2) , 385-402
Experimental Study on Laser Texturing and Electrochemical Multi Bio Coating of Biological Materials
- 7 April 2025
- Published by Springer Nature in Lasers in Manufacturing and Materials Processing
- Vol. 12 (2) , 385-402
Experimental Study on Laser Texturing and Electrochemical Multi Bio Coating of Biological Materials
- 1 January 2025
- Published by University Library in Kragujevac in Advanced Engineering Letters
- Vol. 4 (4) , 210
EXPERIMENTAL INVESTIGATION OF WEAR PERFORMANCE OF Al7075/ZrO2/Gr HYBRID METAL MATRIX COMPOSITES USING TOPSIS AND ANN
This study presents the effects of zirconium dioxide (ZrO2) with 50 nm and graphite (Gr) of 40 µm on the mechanical and tribological behaviour of an aluminium-based metal matrix composite (Al7075) made by stir casting. The tribological behaviour of wear and the frictional qualities of metal matrix composites (MMCs) are further investigated by performing dry sliding wear tests utilising the pin-on-disc method. The TOPSIS Approach was employed to optimise wear parameters such as wear rate (WR) and coefficient of friction (COF). The findings of the analysis of variance demonstrated that the load and incorporation of nanoparticles had a greater influence on WR and COF, respectively. The addition of ZrO2 results in a significant improvement in wear resistance rate, and COF is significantly reduced with reinforcement of higher wt% ZrO2. Artificial neural network (ANN) optimisation is performed to check the TOPSIS outcomes and found that the optimal level and its outputs are P1V1D1M1, with WR is 0.00142 mm3/m and COF is 0.182.
- 1 January 2025
- Published by University Library in Kragujevac in Advanced Engineering Letters
- Vol. 4 (4) , 210
EXPERIMENTAL INVESTIGATION OF WEAR PERFORMANCE OF Al7075/ZrO2/Gr HYBRID METAL MATRIX COMPOSITES USING TOPSIS AND ANN
This study presents the effects of zirconium dioxide (ZrO2) with 50 nm and graphite (Gr) of 40 µm on the mechanical and tribological behaviour of an aluminium-based metal matrix composite (Al7075) made by stir casting. The tribological behaviour of wear and the frictional qualities of metal matrix composites (MMCs) are further investigated by performing dry sliding wear tests utilising the pin-on-disc method. The TOPSIS Approach was employed to optimise wear parameters such as wear rate (WR) and coefficient of friction (COF). The findings of the analysis of variance demonstrated that the load and incorporation of nanoparticles had a greater influence on WR and COF, respectively. The addition of ZrO2 results in a significant improvement in wear resistance rate, and COF is significantly reduced with reinforcement of higher wt% ZrO2. Artificial neural network (ANN) optimisation is performed to check the TOPSIS outcomes and found that the optimal level and its outputs are P1V1D1M1, with WR is 0.00142 mm3/m and COF is 0.182.
- 1 January 2025
- Published by Begell House Inc. Publishers in High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
- Vol. 29 (2) , 47-56
MECHANICAL TESTING OF ALUMINUM METAL MATRIX COMPOSITES REINFORCED WITH 6% AND 8% WEIGHT OF ALUMINA
Aluminium metal matrix composites, or AMMCs, are widely employed in a wide range of engineering applications, such as piston rings, brake drums, cylinder liners, connecting rods, and many more. To make MMCs, the best attributes of each of its constituents−the toughness and ductility of the matrix, and the high modulus and strength of the reinforcement−are combined and customized. For testing, the AMMCs in this study are made from Al6061 alloy reinforced with different weight percentages of Al2O3, such as 6% and 8%, using a stir casting process. Tensile, compressive, wear, and hardness tests are performed on the prepared AMMCs specimen in accordance with ASTM standards. For the 6% and 8% reinforced AMMCs, the corresponding tensile strength is 129 N/mm2 and 140 N/mm2, compressive strength is 384 N/mm2 and 419 N/mm2, coefficient of friction is 0.22 and 0.37, and hardness is 51.72 HV and 52.86 HV.
- 1 January 2025
- Published by Begell House Inc. Publishers in High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
- Vol. 29 (2) , 47-56
MECHANICAL TESTING OF ALUMINUM METAL MATRIX COMPOSITES REINFORCED WITH 6% AND 8% WEIGHT OF ALUMINA
Aluminium metal matrix composites, or AMMCs, are widely employed in a wide range of engineering applications, such as piston rings, brake drums, cylinder liners, connecting rods, and many more. To make MMCs, the best attributes of each of its constituents−the toughness and ductility of the matrix, and the high modulus and strength of the reinforcement−are combined and customized. For testing, the AMMCs in this study are made from Al6061 alloy reinforced with different weight percentages of Al2O3, such as 6% and 8%, using a stir casting process. Tensile, compressive, wear, and hardness tests are performed on the prepared AMMCs specimen in accordance with ASTM standards. For the 6% and 8% reinforced AMMCs, the corresponding tensile strength is 129 N/mm2 and 140 N/mm2, compressive strength is 384 N/mm2 and 419 N/mm2, coefficient of friction is 0.22 and 0.37, and hardness is 51.72 HV and 52.86 HV.
- 30 December 2024
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
OPTIMIZATION OF CUTTING PARAMETER IN TURNING OF SUPER DUPLEX STAINLESS STEEL-SDSS 2507 WITH TEXTURED TOOLS UNDER MQL CONDITIONS
Super-duplex stainless steel (SDSS) 2507 is well known for its complex microstructure and alloying components, which contribute to its exceptional mechanical qualities and resistance to corrosion. Nevertheless, these features provide considerable difficulties during machining. In order to address these challenges and advance sustainability, this work presents a novel machining technique that combines minimal quantity lubrication (MQL) with surface-textured tools. Two different kinds of texture tools were examined: one with linear grooves and the other with a hybrid texture that combined both circular pits and holes. A CNC center lathe machine operating under MQL conditions was used for the experiments. It had two distinct cooling conditions, different tool textures, and cutting parameters like depth of cut, feed rate, and speed. Cutting speed, followed by feed rate, was the most important factor affecting cutting force and tool flank wear, according to analysis of variance (ANOVA). Comparing the hybrid-textured tool under MQL to dry machining conditions, the cutting force was reduced by 40%. A cutting speed of 40[ ]m/min, feed rate of 0.1[ ]mm/rev, and depth of cut of 0.4[ ]mm were found to be the optimal machining parameters employing MQL and hybrid-textured tools for minimizing cutting force and tool wear, the optimal values are 119.57[ ]N and 113.875[ ][ ]m respectively. These findings provide notable enhancements in machinability and sustainability for SDSS 2507, demonstrating the efficiency and usefulness of the suggested approach in MQL machining.
- 30 December 2024
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
OPTIMIZATION OF CUTTING PARAMETER IN TURNING OF SUPER DUPLEX STAINLESS STEEL-SDSS 2507 WITH TEXTURED TOOLS UNDER MQL CONDITIONS
Super-duplex stainless steel (SDSS) 2507 is well known for its complex microstructure and alloying components, which contribute to its exceptional mechanical qualities and resistance to corrosion. Nevertheless, these features provide considerable difficulties during machining. In order to address these challenges and advance sustainability, this work presents a novel machining technique that combines minimal quantity lubrication (MQL) with surface-textured tools. Two different kinds of texture tools were examined: one with linear grooves and the other with a hybrid texture that combined both circular pits and holes. A CNC center lathe machine operating under MQL conditions was used for the experiments. It had two distinct cooling conditions, different tool textures, and cutting parameters like depth of cut, feed rate, and speed. Cutting speed, followed by feed rate, was the most important factor affecting cutting force and tool flank wear, according to analysis of variance (ANOVA). Comparing the hybrid-textured tool under MQL to dry machining conditions, the cutting force was reduced by 40%. A cutting speed of 40[ ]m/min, feed rate of 0.1[ ]mm/rev, and depth of cut of 0.4[ ]mm were found to be the optimal machining parameters employing MQL and hybrid-textured tools for minimizing cutting force and tool wear, the optimal values are 119.57[ ]N and 113.875[ ][ ]m respectively. These findings provide notable enhancements in machinability and sustainability for SDSS 2507, demonstrating the efficiency and usefulness of the suggested approach in MQL machining.
- 23 December 2024
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
SURFACE WETTABILITY STUDIES ON LASER TEXTURED Ti-6Al-4V AND 316L STAINLESS STEEL
The surface wettability of laser-textured Ti-6Al-4V and 316L SS is compared in this work. The surface of Ti-6Al-4V and 316L SS was micro-laser textured with varying dimple distances with the help of a nanosecond fiber laser. The composition of the material is evaluated using Energy Dispersive Spectroscopy and the surface roughness of the laser-textured samples was evaluated using a 3D optical profilometer. The results of the measurement of contact angle reveal information on the substrate’s wettability. The contact angle of Ti-6Al-4V was significantly reduced from 9[ ] to [ ] for 100[ ][ ]m dimple distance at 98% energy while 316L SS contact angle was reduced from [ ] to [ ] for 200[ ][ ]m at 98% energy.
- 23 December 2024
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
SURFACE WETTABILITY STUDIES ON LASER TEXTURED Ti-6Al-4V AND 316L STAINLESS STEEL
The surface wettability of laser-textured Ti-6Al-4V and 316L SS is compared in this work. The surface of Ti-6Al-4V and 316L SS was micro-laser textured with varying dimple distances with the help of a nanosecond fiber laser. The composition of the material is evaluated using Energy Dispersive Spectroscopy and the surface roughness of the laser-textured samples was evaluated using a 3D optical profilometer. The results of the measurement of contact angle reveal information on the substrate’s wettability. The contact angle of Ti-6Al-4V was significantly reduced from 9[ ] to [ ] for 100[ ][ ]m dimple distance at 98% energy while 316L SS contact angle was reduced from [ ] to [ ] for 200[ ][ ]m at 98% energy.
- 19 November 2024
- Published by Elsevier in Ultrasonics
- Vol. 147, 107526
Investigation of electrochemical micromachining on magnesium alloy using hollow tool electrode
- 19 November 2024
- Published by Elsevier in Ultrasonics
- Vol. 147, 107526
Investigation of electrochemical micromachining on magnesium alloy using hollow tool electrode
- 23 July 2024
- Published by IGI Global Scientific Publishing
- p. 1-22
An Application of Deep Neural Network Using GNS for Solving Complex Fluid Dynamics Problems
The present work investigates the possibilities of solving complex fluid dynamics problems using Navier-Stokes equations, through simulation based techniques using deep neural networks in real time and along with provision of a singular architecture that achieves cutting-edge performance while maintaining a very high accuracy and precision at par with ground truth. The study employs Graph Network-based Simulators (GNS) to compute system dynamics. The developed model shows robust behavior in its prediction giving prediction accuracy of around 99%. The model generalizes well from unit-timestep predictions with huge number of particles at training phase, to completely differing starting conditions for timesteps ranging into the thousands and with even more particles at test time. Based on GNS, the model is immune to choices of hyper parameters over differing metrics for evaluation. The proposed model shows that deep learning is effective for solving a large set of complex fluid dynamics related problems in both forwards and backwards in time.
- 23 July 2024
- Published by IGI Global Scientific Publishing
- p. 1-22
An Application of Deep Neural Network Using GNS for Solving Complex Fluid Dynamics Problems
The present work investigates the possibilities of solving complex fluid dynamics problems using Navier-Stokes equations, through simulation based techniques using deep neural networks in real time and along with provision of a singular architecture that achieves cutting-edge performance while maintaining a very high accuracy and precision at par with ground truth. The study employs Graph Network-based Simulators (GNS) to compute system dynamics. The developed model shows robust behavior in its prediction giving prediction accuracy of around 99%. The model generalizes well from unit-timestep predictions with huge number of particles at training phase, to completely differing starting conditions for timesteps ranging into the thousands and with even more particles at test time. Based on GNS, the model is immune to choices of hyper parameters over differing metrics for evaluation. The proposed model shows that deep learning is effective for solving a large set of complex fluid dynamics related problems in both forwards and backwards in time.