MAMustafa Merih Arikan

Mustafa Merih Arikan

*This is an algorithmically generated author record based on publicly available information.

Mustafa Merih Arikan has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A KINETIC STUDY OF THERMOCHEMICALLY BORIDED AISI 316L STAINLESS STEEL

    by Gökhan Başman, Mustafa Merih Arikan, Cevat Arisoy, Kelami Şeşen

    Biomaterials are used in different parts of human body as replacement implants in medical applications. An implant material should have high biocompatibility, corrosion and wear resistance, and suitable mechanical properties in terms of safety and long-service period. There are only a few biocompatible implant materials: AISI316L stainless steel is one of the materials used in this type of applications. They have relatively poor wear resistance. Boriding being a thermochemical diffusion treatment is one of the processes to improve their wear resistance. Borides are formed by introducing boron atoms by diffusion onto a substrate surface and they are non-oxide ceramics and could be very brittle. The growth kinetics of boride layer is analyzed by measuring depth of layers as a function of boriding time within a temperature range. In this study, the effects of Ekabor-2 bath on formation mechanism and properties of boride layer in thermochemical diffusion boriding of AISI316L stainless steel were investigated. Different temperatures and durations were applied in boriding operations and hardness, optical microscopy, XRD, EPMA and SEM studies were performed to detect the properties of boride layers. It was found that thickness of boride layer increased with increasing temperature and time; the basic phase in the boride layer formed was Fe2B and FeB phase also formed. It was also found that surface hardness values of borided materials increased depending on temperature and time of boriding process; surface hardness values of borided materials are approximately 10 times higher than surface hardness values of non-borided AISI316L stainless steel and formation activation energy of boride layer is 149.3 kjmol-1.


  • The Effect of Strain Rate and Initial Grain Size on Deformation Behavior of OFHC Copper at Elevated Temperatures

    by Selim Yildirim, Mustafa Merih Arikan

    Understanding of plastic deformation mechanisms and/or microstructural changes of metals and alloys at elevated temperatures makes possible to control their hot working behavior and final mechanical properties. The aim of the present work is to optimize the conditions to achieve maximum ductility in terms of initial grain size, process temperature and deformation rate. In this study, the OFHC (oxygen-free high conductivity) copper samples of different initial grain sizes (25, 50, 100 and 150 μm) were subjected to tensile tests at temperatures 300, 405, 500 and 700 °C (0.42 - 0.75 Tm) and cross-head speeds of 1, 2, 5, 10, 20 and 50 mm/min (strain rates of 5.6x10-4 - 2.8x10-2 s-1). Experimental results indicated that particular conditions (initial grain size of 50 µm; 700 °C of working temperature and 5.6x10-3 s-1 of strain rate) should be provided in terms of process temperature and deformation rate depending upon initial grain size for dynamic recrystallization and also maximum ductility.

  • Effect of Reduction Ratio below Austenite Recrystallization Stop Temperature on Mechanical Properties of an API X70M PSL2 Line Pipe Steel

    by Mustafa Merih Arikan, Ramazan Tütük, Eyüp Sabri Kayali

    Steel grades having high toughness and high strength are required for line pipes since gas and oil should be transported through them at high pressures. Thermo-mechanically controlled rolling processes are used for increasing both toughness and strength at low temperatures since the line pipes are exposed to harsh climatic conditions at full length and rather severe service conditions. Various test methods such as Charpy, DWTT, CTOA have been used for measurement of toughness values of these steels and the results have been evaluated considering various criteria. In this study, thermo-mechanical rolling trials were performed at the temperature below the recrystallization temperature of austenite on an API X70M PSL2 grade steel, which is large scale used in the oil and natural gas line pipes, to increase the strength without sacrificing the toughness. Different reduction ratios were utilized and the effect of reduction ratios on mechanical properties and microstructures were investigated during the trials. It was observed that final grain size decreased and strength and toughness increased with increasing reduction ratio.


  • Open Access

    BİR LEVHA HADDEHANESİNDEKİ ÜST EĞME SİLİNDİRİ KOVANINDA OLUŞAN HASARIN ANALİZİ

    by Müh Nğü, / Derg, J Ngu, Mustafa Merih

    En tr Premature failure of a bending cylinder bushing in a plate mill was investigated in this study. Visual, chemical and microscopic analyses were performed to detect the possible reasons of this failure and possible measures to be taken were mentioned not to be encountered for this type of failures in the future. No traces of welding were observed in the performed studies. Intensive elongated MnS inclusions, fatigue striations and splits from the grain boundaries were detected in the microstructural investigations. It was also proved that the base of the bushing was worked without chamfering. The importance of the removing hydrogen from the structure by annealing to decrease the hydrogen brittleness risk which would occur after the chromium coating process, and the chamfering of the bushing base to decrease the crack susceptibility was stressed. Bu çalışmada bir levha haddehanesinde eğme silindiri kovanında meydana gelen erken hasar incelenmiştir. Oluşan bu hasarın sebeplerini tespit etmek için görsel, kimyasal ve mikroskobik analizler yapılmış ve gelecekte bu tip hasarlarla karşılaşmamak için alınması gereken tedbirlerden bahsedilmiştir. Gerçekleştirilen çalışmalarda herhangi bir kaynak izine rastlanılmamıştır. Yapılan mikroskobik incelemelerde, şiddetli bir şekilde uzamış MnS inklüzyonları, yorulma adımları ve tane sınırlarından ayrılmalar belirlenmiştir. Ayrıca kovan tabanının pah kırılmadan işlendiği de tespit edilmiştir. Krom kaplama prosesinden sonra oluşabilecek hidrojen gevrekliği riskini azaltmak için tavlama ile yapıdan hidrojenin uzaklaştırılmasının ve çatlak hassasiyetini azaltmak için kovan tabanında pah kırmanın önemi vurgulanmıştır.

  • Open Access

    New Approaches to Aluminum Integral Foam Production with Casting Methods

    by Ahmet Güner, Mustafa Merih Arıkan, Mehmet Nebioglu

    Integral foam has been used in the production of polymer materials for a long time. Metal integral foam casting systems are obtained by transferring and adapting polymer injection technology. Metal integral foam produced by casting has a solid skin at the surface and a foam core. Producing near-net shape reduces production expenses. Insurance companies nowadays want the automotive industry to use metallic foam parts because of their higher impact energy absorption properties. In this paper, manufacturing processes of aluminum integral foam with casting methods will be discussed.


  • Open Access

    Hot Ductility Behavior of a Peritectic Steel during Continuous Casting

    by Mustafa Merih Arıkan

    Hot ductility properties of a peritectic steel for welded gas cylinders during continuous casting were studied by performing hot tensile tests at certain temperatures ranging from 1200 to 700 °C for some cooling rates by using Gleeble-3500 thermo-mechanical test and simulation machine in this study. The effects of cooling rate and strain rate on hot ductility were investigated and continuous casting process map (time-temperature-ductility) were plotted for this material. Reduction of area (RA) decreases and cracking susceptibility increases during cooling from solidification between certain temperatures depending on the cooling rate. Although the temperatures which fracture behavior change upon cooling during continuous casting may vary for different materials, it was found that the type of fracture was ductile at 1100 and 1050 °C; semi-ductile at 1000 °C, and brittle at 800 °C for the steel P245NB. There is a ductility trough between 1000 and 725 °C. The ductility trough gets slightly narrower as the cooling rate decreases.


  • Tunable negative and positive coercivity forSmCo∕(Co∕Gd)exchange springs investigated with SQUID magnetometry

    by S. Demirtas, M. R. Hossu, M. Arikan, A. R. Koymen, M. B. Salamon

    Temperature dependent static magnetic properties of Co∕Gd multilayers, grown on SmCo, are experimentally investigated by means of SQUID magnetometry. The SmCo∕(Co∕Gd) system shows an exchange spring behavior above the compensation temperature (Tcomp) at which the magnetization of the antiferromagnetically coupled multilayer is zero. Below Tcomp, a tunable negative coercivity state (inverse hysteresis) appears, due to the coupling between the hard SmCo and soft Co∕Gd multilayers, irrespective of whether Co or Gd is proximate to the SmCo. However, for the strongly ferromagnetically coupled Co interface layer, negative coercivity persists over a larger temperature interval. The negative coercivity state vanishes if the coercivity of the SmCo layer is increased by controlling the Cu underlayer thickness.


  • The effect of titanium on the abrasion resistance of 15Cr–3Mo white cast iron

    by M.M Arikan, H Çimenoğlu, E.S Kayali