JLJane-Sunn Liaw

Jane-Sunn Liaw

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jane-Sunn Liaw has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Recent Progress in Fill Media Technology for Wet Cooling Towers

    by Zahra Hashemi, Abdolmajid Zamanifard, Maysam Gholampour, Jane-Sunn Liaw, Chi-Chuan Wang

    Cooling towers are extensively utilized in diverse industries for efficient heat dissipation. Fill media are a critical component, facilitating heat and mass exchange between water and air, impacting overall cooling tower efficiency. Given its vital importance, this study comprehensively reviews recent advancements in fill media technology, illuminating cooling tower technology progress and exploring the effects of different fill media configurations and materials on cooling tower performance. It should be noted that the majority of research is focused on the Range of 2.5 °C to 25 °C and Approach of 1 °C to 9 °C. Through comprehensive analysis and evaluation, the effects of various fill media on heat transfer efficiency, water cooling capacity, and energy consumption are intensively summarized. By understanding these effects, engineers and designers can make rational decisions to optimize cooling tower performance and ensure efficient heat dissipation. Notably, in some reported cases, new fill media enhanced cooling range, effectiveness, and the Merkel number by 28%, 85%, and 131%, respectively. Ultimately, this paper serves as a valuable resource for academics, researchers, and professionals in the field of cooling tower design and thermal management. The insights provided in this study can help industries achieve greater energy efficiency, sustainability, and overall operational excellence.


  • Open Access

    A Comprehensive Review on the Nucleate/Convective Boiling of Low-GWP Refrigerants: Alternatives to HFC Refrigerants

    by Qadir Nawaz Shafiq, Jane-Sunn Liaw, Chi-Chuan Wang

    This review presents the nucleate/convective boiling performance for a variety of important low global warming potential (LGWP) alternatives to commonly used high-global warming potential (GWP) refrigerants (such as R-134a, R404A, and R-410A, etc.). Efforts are stressed on the assessment of their evaporation pressure drop and heat transfer coefficient (HTC) characteristics. These alternatives include R-1234ze(Z), R-1234ze(E), R-1233zd (E), R-1234ze(E), R-410A, R-1234yf, and R-513A. The authors investigated the thermo-fluid properties within and outside a tube, mini-channel, micro-fin tube, and plate heat exchanger. The investigation of the numerical, experimental, and simulated results revealed that the evaporation pressure drop and HTC characteristics were dependent on a variety of variables. These factors include the working fluid’s thermodynamics and transport properties, the refrigerant’s mass flux, heat flux, saturation temperature, the vapor quality, the conditions and flow patterns, the orientation of the heating surface, and the geometry (shape, size, and surface area smooth/enhanced) of the heating surface. An expanded LGWP refrigerants, surfaces, and conditions database is needed. Mechanistic models may assist. These models can optimize boiling, anticipate heat transfer, and develop high-performance geometries.


  • Open Access

    Parametric Analysis of Cylinder Drying Process in Association with Various Materials

    by Ngoctan Tran, Akash Sengupta, Jane-Sunn Liaw, Chi-Chuan Wang

    In this study, the heat and mass transfers in the fabric drying process of a single-cylinder dryer are numerically examined in detail by using MATLAB codes and illustrating 3D velocity and temperature profiles obtained by a CFD-ACE+ software package. Seven different drying materials including Polyethylene terephthalate (PET), Polyethylene, Polypropylene, Cotton, Wool, Rayon, and Nylon are employed as drying materials. Influences of the drying-material thickness, contacting percentage, cylinder temperature, feeding velocity, and cylinder diameter are examined in detail. For all cases in this study, it is found that the maximum temperature of the drying material in the drying process is strongly dependent on the thermal diffusivity of the drying material. The higher the thermal diffusivity of the drying material, the greater the peak temperature achieved. The peak temperature of the drying material increases with the increase in the contacting percentage. The higher feeding velocity leads to a faster increase in the temperature of the drying material; however, the peak temperature of the slower feeding velocity is higher than that of the faster one. The heat transfer between the central layer of the drying material and to ambient environment is limited by the thermal diffusivity of the drying material.


  • Open Access

    A Criterion of Heat Transfer Deterioration for Supercritical Organic Fluids Flowing Upward and Its Heat Transfer Correlation

    by Yung-Ming Li, Jane-Sunn Liaw, Chi-Chuan Wang

    The main objective of this study was to develop the supercritical heat transfer correlation applicable for organic fluids when flowing upward in smooth tubes based on the available experimental data. The organic fluids contain R-22, R-134a, R-245fa and Ethanol and the associated heat transfer characteristics were compared with non-organic fluids like water and carbon-dioxide (CO2). It was found that the limit heat flux may result in heat transfer deterioration (HTD) of organic fluid and the corresponding values are much smaller than water or CO2. A new criterion to predict the HTD was developed and this criterion yields the best predictive ability against database. It was found that HTD occurs can be well described by the acceleration parameter evaluated at the wall condition rather than at bulk condition. For estimation of the supercritical heat transfer coefficient (HTC) for organic fluid, the present study proposes a new correlation with a physically based correction factor, which gives satisfactory predictions against the HTC of supercritical organic fluid. The new correlation can offer the smallest average deviation of 0.007 and standard deviation of 0.181 among the existing correlations.


  • Open Access

    Airside Performance of H-Type Finned Tube Banks with Surface Modifications

    by Pradhyumn Bhale, Mrinal Kaushik, Jane-Sunn Liaw, Chi-Chuan Wang

    The present study numerically investigates some novel modifications to augment the performance of the H-type finned tube banks, which are widely used in waste heat recovery in industries. The imposed modifications upon the original H-type finned tube banks include the following: (1) Design 1 contains some triangular cuts at the edge of the original rectangular fin; (2) Design 2 modifies the original rectangular geometry into a trapezoid shape; (3) Design 3 renders the original rectangular cross-section fin thickness into trapezoid cross-section; and (4) Design 4 changes the original rectangular shape into a circular shape. Based on the simulations, it is found that Design 1 shows barely any improvements in the heat transfer performance and surface area reduction. Design 2 can provide some weight saving and surface area reduction at a slightly inferior heat transfer performance. Design 3 can offer up to 14% improvements in the overall heat transfer performance without any pumping power penalty. Yet, Design 4 provides the maximum weight saving as compared to the original reference case. With 3–9% lesser surface area than the reference case, Design 4 still offers marginally higher heat transfer performance.


  • Open Access

    Compound Heat Transfer Enhancement of Wavy Fin-and-Tube Heat Exchangers through Boundary Layer Restarting and Swirled Flow

    by Ali Sadeghianjahromi, Saeid Kheradmand, Hossain Nemati, Jane-Sunn Liaw, Chi-Chuan Wang

    This study performs a 3D turbulent flow numerical simulation to improve heat transfer characteristics of wavy fin-and-tube heat exchangers. A compound design encompassing louver, flat, and vortex generator onto wavy fins can significantly enhance the heat transfer performance of wavy fin-and-tube heat exchangers. Replacement of wavy fins around tubes with flat fins is not effective as far as the reduction of thermal resistance is concerned, although an appreciable pressure drop reduction can be achieved. Adding two louvers with a width of 8 mm to the flat portion can reduce thermal resistance up to 6% in comparison with the reference wavy fin. Increasing the louver number and width can further decrease the thermal resistance. Also, it is found that the optimum louver angle is equal to the wavy angle for offering the lowest thermal resistance. Therefore, compound geometry with three louvers, a width of 12 mm, and the louver angle being equal to wavy angle with waffle height to be the same as fin pitch of the reference wavy fin has the most reduction in thermal resistance of 16% for a pumping power of 0.001 W. Adding punching longitudinal vortex generators on this compound geometry can further decrease thermal resistance up to 18%.