John J. Pittari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
John J. Pittari has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
Jeffrey J. Swab
3 shared publicationsGhatu Subhash
2 shared publications- Ghatu Subhash
Department of Mechanical and Aerospace Engineering, University of Florida, Gainesville, USA
2 shared publications James Zheng
2 shared publications- Jeffrey J. Swab
US Army Research Laboratory Aberdeen Proving Ground Maryland 21005
2 shared publications Virginia Halls
2 shared publications
Latest Publications
- 10 September 2022
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 20 (1) , 509-518
Compression strength of tungsten carbide–cobalt hard metals
Eight tungsten carbide (WC) materials containing different cobalt (Co) contents (3‒12 wt.%) and with different WC grain sizes (.4‒1.85 μm) were subjected to compressive loading under quasi‐static and dynamic conditions using a dumbbell‐shaped specimen geometry. The materials exhibited varying degrees of inelastic strain prior to final fracture under both loading conditions. Inelastic strain was consistent under dynamic loading but varied with Co content and WC grain size under quasi‐static loading. The only material to exhibit a strain‐rate‐dependent compression strength was the material containing the highest level of Co (12%) and the largest WC grain size (1.85 μm) indicating a potential threshold level of Co content and/or WC grain size where the compressive strength is insensitive to the strain rate.
- 10 September 2022
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 20 (1) , 509-518
Compression strength of tungsten carbide–cobalt hard metals
Eight tungsten carbide (WC) materials containing different cobalt (Co) contents (3‒12 wt.%) and with different WC grain sizes (.4‒1.85 μm) were subjected to compressive loading under quasi‐static and dynamic conditions using a dumbbell‐shaped specimen geometry. The materials exhibited varying degrees of inelastic strain prior to final fracture under both loading conditions. Inelastic strain was consistent under dynamic loading but varied with Co content and WC grain size under quasi‐static loading. The only material to exhibit a strain‐rate‐dependent compression strength was the material containing the highest level of Co (12%) and the largest WC grain size (1.85 μm) indicating a potential threshold level of Co content and/or WC grain size where the compressive strength is insensitive to the strain rate.
- 3 September 2020
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 7 (1) , 34-47
Dynamic Compression Strength of Ceramics: What was Learned from an Interlaboratory Round Robin Exercise?
- 3 September 2020
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 7 (1) , 34-47
Dynamic Compression Strength of Ceramics: What was Learned from an Interlaboratory Round Robin Exercise?
- 1 June 2019
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 39 (6) , 1965-1973
Uniaxial tensile strength and fracture analysis of a hot-pressed boron carbide
- 1 June 2019
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 39 (6) , 1965-1973
Uniaxial tensile strength and fracture analysis of a hot-pressed boron carbide
- Open Access
- 22 February 2019
- Published by Springer Nature in JOM
- Vol. 71 (4) , 1535-1542
Additive Manufacturing of Cemented Tungsten Carbide with a Cobalt-Free Alloy Binder by Selective Laser Melting for High-Hardness Applications
- 22 February 2019
- Published by Springer Nature in JOM
- Vol. 71 (4) , 1535-1542
Open AccessAdditive Manufacturing of Cemented Tungsten Carbide with a Cobalt-Free Alloy Binder by Selective Laser Melting for High-Hardness Applications
- 1 September 2018
- Published by Elsevier in International Journal of Refractory Metals and Hard Materials
- Vol. 75, 294-298
Dynamic hardness of cemented tungsten carbides
- 1 September 2018
- Published by Elsevier in International Journal of Refractory Metals and Hard Materials
- Vol. 75, 294-298
Dynamic hardness of cemented tungsten carbides
- 16 June 2016
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 99 (10) , 3398-3405
Rate‐Dependent Mechanical Behavior and Amorphization of Ultrafine‐Grained Boron Carbide
An investigation into mechanical properties and amorphization behavior of ultrafine‐grained (0.3 μm) boron carbide (B 4 C) is conducted and compared to a baseline coarse‐grained (10 μm) boron carbide. Static and dynamic uniaxial compressive strength, and static and dynamic Vickers indentation hardness were determined, and Raman spectroscopy was then conducted on indented regions to quantify and compare the intensity of amorphization. In relation to coarse‐grained B 4 C the ultrafine‐grained material exhibited, on average, a 33% higher static compressive strength, 20% higher dynamic compressive strength, 10% higher static Vickers hardness, and 23% higher dynamic Vickers hardness. In addition, there was an 18% reduction in indentation‐induced radial crack length in ultrafine‐grained B 4 C, which corresponded to an increase in estimated fracture toughness. Although traditional coarse‐grained B 4 C exhibits an 8.6% decrease in hardness from the static to dynamic regimes, ultrafine‐grained B 4 C showed only negligible change under similar conditions, suggesting a reduced propensity for amorphization. Raman spectroscopic analysis confirmed this result by revealing significantly lower amorphization intensity in ultrafine‐B 4 C compared to coarse‐grained B 4 C. These results may have significant positive implications in the implementation of ultrafine‐grained boron carbide as a material for improved performance in impact and other high‐pressure applications.
- 16 June 2016
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 99 (10) , 3398-3405
Rate‐Dependent Mechanical Behavior and Amorphization of Ultrafine‐Grained Boron Carbide
An investigation into mechanical properties and amorphization behavior of ultrafine‐grained (0.3 μm) boron carbide (B 4 C) is conducted and compared to a baseline coarse‐grained (10 μm) boron carbide. Static and dynamic uniaxial compressive strength, and static and dynamic Vickers indentation hardness were determined, and Raman spectroscopy was then conducted on indented regions to quantify and compare the intensity of amorphization. In relation to coarse‐grained B 4 C the ultrafine‐grained material exhibited, on average, a 33% higher static compressive strength, 20% higher dynamic compressive strength, 10% higher static Vickers hardness, and 23% higher dynamic Vickers hardness. In addition, there was an 18% reduction in indentation‐induced radial crack length in ultrafine‐grained B 4 C, which corresponded to an increase in estimated fracture toughness. Although traditional coarse‐grained B 4 C exhibits an 8.6% decrease in hardness from the static to dynamic regimes, ultrafine‐grained B 4 C showed only negligible change under similar conditions, suggesting a reduced propensity for amorphization. Raman spectroscopic analysis confirmed this result by revealing significantly lower amorphization intensity in ultrafine‐B 4 C compared to coarse‐grained B 4 C. These results may have significant positive implications in the implementation of ultrafine‐grained boron carbide as a material for improved performance in impact and other high‐pressure applications.
- 1 December 2015
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 35 (16) , 4411-4422
The rate-dependent fracture toughness of silicon carbide- and boron carbide-based ceramics
- 1 December 2015
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 35 (16) , 4411-4422
The rate-dependent fracture toughness of silicon carbide- and boron carbide-based ceramics
- 17 October 2014
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 12 (S2)
The Rate‐Dependent Response of Pressureless‐Sintered and Reaction‐bonded Silicon Carbide‐Based Ceramics
A comparison of the static and dynamic hardness and compressive strengths of seven different commercially available pressureless‐sintered ( PS ) and reaction‐bonded ( RB ) silicon carbide‐based ceramics is presented. The intent is to relate these mechanical properties to the microstructure formed during processing. Fine‐grained sintered SiC performed better than coarse‐grained SiC under indentation and compression loading. The sintered specimens had greater hardness and strength than the RB materials that contained a weaker silicon phase. Composite ceramics containing diamond and boron carbide as secondary phases exhibited greater hardness than the other materials. In addition, the compressive strength and hardness improved with strain rate of deformation for all the materials except for the RB materials and SiC–B 4 C composite. The weakening effect observed in the SiC–B 4 C composite during dynamic indentation can be attributed to the B 4 C phase which exhibits localized amorphization; however, the deleterious effects of B 4 C amorphization were reduced due to the strain‐rate hardening of SiC.
- 17 October 2014
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 12 (S2)
The Rate‐Dependent Response of Pressureless‐Sintered and Reaction‐bonded Silicon Carbide‐Based Ceramics
A comparison of the static and dynamic hardness and compressive strengths of seven different commercially available pressureless‐sintered ( PS ) and reaction‐bonded ( RB ) silicon carbide‐based ceramics is presented. The intent is to relate these mechanical properties to the microstructure formed during processing. Fine‐grained sintered SiC performed better than coarse‐grained SiC under indentation and compression loading. The sintered specimens had greater hardness and strength than the RB materials that contained a weaker silicon phase. Composite ceramics containing diamond and boron carbide as secondary phases exhibited greater hardness than the other materials. In addition, the compressive strength and hardness improved with strain rate of deformation for all the materials except for the RB materials and SiC–B 4 C composite. The weakening effect observed in the SiC–B 4 C composite during dynamic indentation can be attributed to the B 4 C phase which exhibits localized amorphization; however, the deleterious effects of B 4 C amorphization were reduced due to the strain‐rate hardening of SiC.
- 11 July 2014
- Published by Springer Nature
- p. 207-212
Fracture Toughness Testing of Advanced Silicon Carbide Ceramics Using Digital Image Correlation
- 11 July 2014
- Published by Springer Nature
- p. 207-212
Fracture Toughness Testing of Advanced Silicon Carbide Ceramics Using Digital Image Correlation