Geoffrey Gregory
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Geoffrey Gregory has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Kristopher Olan Davis
University of Central Florida
9 shared publications - Haider Ali
Department of Materials Science and Engineering, University of Central Florida, Orlando, FL, USA
4 shared publications - Titel Jurca
Department of Chemistry, University of Central Florida, Orlando, Florida 32816, USA
4 shared publications - Andrew M. Gabor
BrightSpot Automation LLC, Boulder, CO, USA
2 shared publications Corbin Feit
Department of Materials Science and Engineering University of Central Florida Orlando FL 32816 USA
2 shared publicationsMengjie Li
Department of Materials Science and Engineering University of Central Florida Orlando FL 32816 USA
2 shared publications
Latest Publications
- Open Access
- 22 December 2021
- Published by Frontiers Media SA in Frontiers in Space Technologies
- Vol. 2
Design and Validation of a Device for Mitigating Fluid Microgravity Effects in Biological Research in Canister Spaceflight Hardware
The major factor influencing the behavior of microbes growing in liquids in space is microgravity. We recently measured the transcriptomic response of the Gram-positive bacterium Bacillus subtilis to the microgravity environment inside the International Space Station (ISS) in spaceflight hardware called Biological Research in Canisters-Petri Dish Fixation Units (BRIC-PDFUs). In two separate experiments in the ISS, dubbed BRIC-21 and BRIC-23, we grew multiple replicates of the same B. subtilis strain in the same hardware, growth medium, and temperature with matching ground control samples (npj Micrograv. 5:1.2019, doi: 10.1038/s41526-018-0061-0). In both experiments we observed similar responses of the transcriptome to spaceflight. However, we also noted that the liquid cultures assumed a different configuration in microgravity (a toroidal shape) compared with the ground control samples (a flat disc shape), leading us to question whether the transcriptome differences we observed were a direct result of microgravity, or a secondary result of the different liquid geometries of the samples affecting, for example, oxygen availability. To mitigate the influence of microgravity on liquid geometry in BRIC canisters, we have designed an insert to replace the standard 60-mm Petri dish in BRIC-PDFU or BRIC-LED sample compartments. In this design, liquid cultures are expected to assume a more disk-like configuration regardless of gravity or its absence. We have: (i) constructed a prototype device by 3D printing; (ii) evaluated different starting materials, treatments, and coatings for their wettability (i.e., hydrophilicity) using contact angle measurements; (iii) confirmed that the device performs as designed by drop-tower testing and; (iv) performed material biocompatibility studies using liquid cultures of Bacillus subtilis and Staphylococcus aureus bacteria. Future microgravity testing of the device in the ISS is planned.
- 22 December 2021
- Published by Frontiers Media SA in Frontiers in Space Technologies
- Vol. 2
Open AccessDesign and Validation of a Device for Mitigating Fluid Microgravity Effects in Biological Research in Canister Spaceflight Hardware
The major factor influencing the behavior of microbes growing in liquids in space is microgravity. We recently measured the transcriptomic response of the Gram-positive bacterium Bacillus subtilis to the microgravity environment inside the International Space Station (ISS) in spaceflight hardware called Biological Research in Canisters-Petri Dish Fixation Units (BRIC-PDFUs). In two separate experiments in the ISS, dubbed BRIC-21 and BRIC-23, we grew multiple replicates of the same B. subtilis strain in the same hardware, growth medium, and temperature with matching ground control samples (npj Micrograv. 5:1.2019, doi: 10.1038/s41526-018-0061-0). In both experiments we observed similar responses of the transcriptome to spaceflight. However, we also noted that the liquid cultures assumed a different configuration in microgravity (a toroidal shape) compared with the ground control samples (a flat disc shape), leading us to question whether the transcriptome differences we observed were a direct result of microgravity, or a secondary result of the different liquid geometries of the samples affecting, for example, oxygen availability. To mitigate the influence of microgravity on liquid geometry in BRIC canisters, we have designed an insert to replace the standard 60-mm Petri dish in BRIC-PDFU or BRIC-LED sample compartments. In this design, liquid cultures are expected to assume a more disk-like configuration regardless of gravity or its absence. We have: (i) constructed a prototype device by 3D printing; (ii) evaluated different starting materials, treatments, and coatings for their wettability (i.e., hydrophilicity) using contact angle measurements; (iii) confirmed that the device performs as designed by drop-tower testing and; (iv) performed material biocompatibility studies using liquid cultures of Bacillus subtilis and Staphylococcus aureus bacteria. Future microgravity testing of the device in the ISS is planned.
- 9 July 2021
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 54 (38) , 384003
Phosphorus-doped polysilicon passivating contacts deposited by atmospheric pressure chemical vapor deposition
In this work, we present a high quality tunnel oxide passivating, electron-selective contact that is formed using an in-situ phosphorus-doped polycrystalline silicon (poly-Si) layer deposited using an in-line atmospheric pressure chemical vapor deposition (APCVD) process. In-line APCVD is a single-sided deposition process that does not require vacuum systems and is well suited for high volume manufacturing. To fabricate this tunnel oxide passivating contact (TOPCon), we deposit an amorphous silicon (a-Si) layer on silicon oxide (SiO x ) passivated n -type crystalline silicon (c-Si) followed by an annealing step at around 910 ∘ C, which provides solid phase crystallization. The contact shows an excellent surface passivation quality with an effective minority carrier lifetime of ≈4.2 ms and an implied open circuit voltage ( iV OC ) of ≈717 mV after annealing without any additional hydrogenation process. Saturation current density ( J 0 ) of ≈18 fA cm −2 is recorded for this contact. Contact resistivity ( ρ c ) of ≈50 mΩ·cm −2 and junction resistivity of ≈0.24 Ω·cm −2 are realized with e-beam evaporated aluminium (Al) metal contact.
- 9 July 2021
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 54 (38) , 384003
Phosphorus-doped polysilicon passivating contacts deposited by atmospheric pressure chemical vapor deposition
In this work, we present a high quality tunnel oxide passivating, electron-selective contact that is formed using an in-situ phosphorus-doped polycrystalline silicon (poly-Si) layer deposited using an in-line atmospheric pressure chemical vapor deposition (APCVD) process. In-line APCVD is a single-sided deposition process that does not require vacuum systems and is well suited for high volume manufacturing. To fabricate this tunnel oxide passivating contact (TOPCon), we deposit an amorphous silicon (a-Si) layer on silicon oxide (SiO x ) passivated n -type crystalline silicon (c-Si) followed by an annealing step at around 910 ∘ C, which provides solid phase crystallization. The contact shows an excellent surface passivation quality with an effective minority carrier lifetime of ≈4.2 ms and an implied open circuit voltage ( iV OC ) of ≈717 mV after annealing without any additional hydrogenation process. Saturation current density ( J 0 ) of ≈18 fA cm −2 is recorded for this contact. Contact resistivity ( ρ c ) of ≈50 mΩ·cm −2 and junction resistivity of ≈0.24 Ω·cm −2 are realized with e-beam evaporated aluminium (Al) metal contact.
- 29 December 2020
- Published by Office of Scientific and Technical Information (OSTI)
Metal Oxide Passivating Contacts using Low-Cost Spatial Atomic Layer Deposition - Final Technical Report
In this project, the University of Central Florida (UCF) worked to both increase module efficiency and reduce manufacturing cost by driving demonstrated lab-scale passivating contact technology using materials and processes compatible with high-volume manufacturing for crystalline silicon (c-Si) photovoltaic (PV) cells.
- 29 December 2020
- Published by Office of Scientific and Technical Information (OSTI)
Metal Oxide Passivating Contacts using Low-Cost Spatial Atomic Layer Deposition - Final Technical Report
In this project, the University of Central Florida (UCF) worked to both increase module efficiency and reduce manufacturing cost by driving demonstrated lab-scale passivating contact technology using materials and processes compatible with high-volume manufacturing for crystalline silicon (c-Si) photovoltaic (PV) cells.
- 5 October 2020
- Published by Wiley in Advanced Materials Interfaces
- Vol. 7 (22) , 2000895
Spatial Atomic Layer Deposition of Molybdenum Oxide for Industrial Solar Cells
Molybdenum oxide thin films are successfully deposited using spatial atomic layer deposition (SALD), a tool designed for high‐throughput industrial film growth. The structural and optical properties of the film are evaluated using ultraviolet photoelectron spectroscopy, high‐resolution transmission electron microscopy, and spectroscopic ellipsometry. To demonstrate the applicability of molybdenum oxide in industrial settings the films are applied as hole‐selective silicon heterojunction contacts for solar cells. When paired with intrinsic amorphous silicon passivation layers, implied open‐circuit voltages of 699 mV are achieved. The carrier transport is unaffected by low‐temperature contact anneals up to 300 °C with contact resistivities of ≈ 10 mΩ cm2. Finally, the optical performance of silicon solar cells featuring different front hole‐selective heterojunction structures are simulated. It is shown that the generation current density of heterojunction solar cells can be significantly increased with the addition of SALD molybdenum oxide contacts.
- 5 October 2020
- Published by Wiley in Advanced Materials Interfaces
- Vol. 7 (22) , 2000895
Spatial Atomic Layer Deposition of Molybdenum Oxide for Industrial Solar Cells
Molybdenum oxide thin films are successfully deposited using spatial atomic layer deposition (SALD), a tool designed for high‐throughput industrial film growth. The structural and optical properties of the film are evaluated using ultraviolet photoelectron spectroscopy, high‐resolution transmission electron microscopy, and spectroscopic ellipsometry. To demonstrate the applicability of molybdenum oxide in industrial settings the films are applied as hole‐selective silicon heterojunction contacts for solar cells. When paired with intrinsic amorphous silicon passivation layers, implied open‐circuit voltages of 699 mV are achieved. The carrier transport is unaffected by low‐temperature contact anneals up to 300 °C with contact resistivities of ≈ 10 mΩ cm2. Finally, the optical performance of silicon solar cells featuring different front hole‐selective heterojunction structures are simulated. It is shown that the generation current density of heterojunction solar cells can be significantly increased with the addition of SALD molybdenum oxide contacts.
- 2 September 2020
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (11) , 2000368
Recombination and Resistive Losses of Transferred Foil Contacts for Silicon Heterojunction Solar Cells
Silicon heterojunction (SHJ) solar cells have been studied extensively due to their potential to reach high energy conversion efficiencies. However, one of the limiting factors for this technology is the metallization, which uses low‐curing‐temperature silver pastes that result in fingers with higher bulk resistivity. Herein, a simple approach to fabricate the SHJ solar cell contacts is demonstrated with commercially available low‐cost silver (Ag) electrically conductive adhesive (ECA) pastes and aluminium (Al) foils. This technique can result in a transparent conductive oxide (TCO)‐free cell structure and has the potential to combine cell metallization and interconnection. Recombination and resistive loss analyses are performed on the fabricated test samples. A dark saturation current density at the contact (J0c) of 3.05 fA cm−2 for test samples before annealing is reported. The analysis of the experimental and simulated photoluminescence (PL) images shows negligible added recombination. The contact resistivity (ρc) value is 49.3 mΩ cm2 after annealing which can be optimized by specialized ECA pastes.
- 2 September 2020
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 14 (11) , 2000368
Recombination and Resistive Losses of Transferred Foil Contacts for Silicon Heterojunction Solar Cells
Silicon heterojunction (SHJ) solar cells have been studied extensively due to their potential to reach high energy conversion efficiencies. However, one of the limiting factors for this technology is the metallization, which uses low‐curing‐temperature silver pastes that result in fingers with higher bulk resistivity. Herein, a simple approach to fabricate the SHJ solar cell contacts is demonstrated with commercially available low‐cost silver (Ag) electrically conductive adhesive (ECA) pastes and aluminium (Al) foils. This technique can result in a transparent conductive oxide (TCO)‐free cell structure and has the potential to combine cell metallization and interconnection. Recombination and resistive loss analyses are performed on the fabricated test samples. A dark saturation current density at the contact (J0c) of 3.05 fA cm−2 for test samples before annealing is reported. The analysis of the experimental and simulated photoluminescence (PL) images shows negligible added recombination. The contact resistivity (ρc) value is 49.3 mΩ cm2 after annealing which can be optimized by specialized ECA pastes.
- Open Access
- 7 August 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (15)
Improving the Passivation of Molybdenum Oxide Hole‐Selective Contacts with 1 nm Hydrogenated Aluminum Oxide Films for Silicon Solar Cells
- 7 August 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (15)
Open AccessImproving the Passivation of Molybdenum Oxide Hole‐Selective Contacts with 1 nm Hydrogenated Aluminum Oxide Films for Silicon Solar Cells
- 4 July 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (18)
Spatial Atomic Layer Deposition of Aluminum Oxide as a Passivating Hole Contact for Silicon Solar Cells
Herein, tunneling aluminum oxide (Al2O3) passivation layers are demonstrated to be a candidate for hole collecting, passivating contacts when coupled with a boron‐doped surface. These very thin Al2O3 films (1.5–3 nm) are deposited using spatial atomic layer deposition (ALD) on boron diffused (110–115 Ω □−1) hydrophilic surfaces operating as metal–insulator–semiconductor (MIS) contacts. The emitter saturation current density values of ≈57 fA cm−2 are achieved for the Al2O3 film thicknesses of 2 nm before metallization. At this same thickness, the contact resistivity values of 33 mΩ cm2 are obtained after metallization. Most importantly, the boron diffusion, wet chemical surface preparation, and spatial ALD of Al2O3 used to create these MIS structures are all performed with industrially relevant equipment on Cz wafers.
- 4 July 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (18)
Spatial Atomic Layer Deposition of Aluminum Oxide as a Passivating Hole Contact for Silicon Solar Cells
Herein, tunneling aluminum oxide (Al2O3) passivation layers are demonstrated to be a candidate for hole collecting, passivating contacts when coupled with a boron‐doped surface. These very thin Al2O3 films (1.5–3 nm) are deposited using spatial atomic layer deposition (ALD) on boron diffused (110–115 Ω □−1) hydrophilic surfaces operating as metal–insulator–semiconductor (MIS) contacts. The emitter saturation current density values of ≈57 fA cm−2 are achieved for the Al2O3 film thicknesses of 2 nm before metallization. At this same thickness, the contact resistivity values of 33 mΩ cm2 are obtained after metallization. Most importantly, the boron diffusion, wet chemical surface preparation, and spatial ALD of Al2O3 used to create these MIS structures are all performed with industrially relevant equipment on Cz wafers.
- 27 May 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (15) , 2000093
Improving the Passivation of Molybdenum Oxide Hole‐Selective Contacts with 1 nm Hydrogenated Aluminum Oxide Films for Silicon Solar Cells
The intrinsic and doped amorphous silicon layers in silicon heterojunction solar cells parasitically absorb light in the short wavelength region of the solar spectrum, lowering the generation current available to the device. Herein, a promising alternative to the hole‐selective amorphous silicon contact layers using only wide bandgap, transparent oxide materials is presented. Using thermal atomic layer deposition, a 1 nm hydrogenated aluminum oxide layer is deposited followed by a 4 nm molybdenum oxide layer on n‐type crystalline silicon. This contact stack provides an effective carrier lifetime of 1.14 ms. It is shown that the molybdenum oxide layer is successfully deposited with a high work function, which facilitates efficient hole extraction and repels majority carriers from the c‐Si surface. Then the implied open‐circuit voltage, saturation current density, and contact resistivity are recorded as a function of contact annealing temperature and show that they are relatively stable up to 200 °C.
- 27 May 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (15) , 2000093
Improving the Passivation of Molybdenum Oxide Hole‐Selective Contacts with 1 nm Hydrogenated Aluminum Oxide Films for Silicon Solar Cells
The intrinsic and doped amorphous silicon layers in silicon heterojunction solar cells parasitically absorb light in the short wavelength region of the solar spectrum, lowering the generation current available to the device. Herein, a promising alternative to the hole‐selective amorphous silicon contact layers using only wide bandgap, transparent oxide materials is presented. Using thermal atomic layer deposition, a 1 nm hydrogenated aluminum oxide layer is deposited followed by a 4 nm molybdenum oxide layer on n‐type crystalline silicon. This contact stack provides an effective carrier lifetime of 1.14 ms. It is shown that the molybdenum oxide layer is successfully deposited with a high work function, which facilitates efficient hole extraction and repels majority carriers from the c‐Si surface. Then the implied open‐circuit voltage, saturation current density, and contact resistivity are recorded as a function of contact annealing temperature and show that they are relatively stable up to 200 °C.
- 21 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 9 (6) , 1800-1805
Nondestructive Contact Resistivity Measurements on Solar Cells Using the Circular Transmission Line Method
- 21 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 9 (6) , 1800-1805
Nondestructive Contact Resistivity Measurements on Solar Cells Using the Circular Transmission Line Method
- 5 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 9 (5) , 1350-1359
A Comprehensive Methodology to Evaluate Losses and Process Variations in Silicon Solar Cell Manufacturing
Novel, high-throughput metrology methods are used in this paper for detailed performance loss analysis of approximately 400 industrial crystalline silicon solar cells, all coming from the same production line. The characterization sequence combines traditional global cell measurements (e.g., current–voltage, Suns- ${V}_{\text{OC}}$ ) with camera-based cell imaging of voltage distribution and power dissipation from photoluminescence and lock-in thermography, respectively. Spatial variations in current collection are visualized using a high-speed external quantum efficiency and reflectance measurement technique. A nondestructive transfer length method (TLM) measurement technique is also implemented, featuring circular TLM structures hidden within the busbars of the cells. The variance of individual loss parameters and their impact on cell performance are quantified for this large group of cells. Based on correlations performed across parameters, recombination losses in the bulk and rear surface of the cell are shown to be the primary limiting factor for the cell efficiency. The nature of these distributions and correlations provide important insights about loss mechanisms in industrial solar cells, helping to prioritize efforts for optimizing the performance of the production line. Additionally, many of the parameters extracted from these techniques can be tied back to incoming material quality issues (e.g., poor bulk carrier lifetime, nonuniform wafer doping) and to individual unit processes (e.g., texturing, phosphorus diffusion, silicon nitride deposition, metallization), allowing the data to be used directly for process control in manufacturing. All of the datasets are made available for download.
- 5 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 9 (5) , 1350-1359
A Comprehensive Methodology to Evaluate Losses and Process Variations in Silicon Solar Cell Manufacturing
Novel, high-throughput metrology methods are used in this paper for detailed performance loss analysis of approximately 400 industrial crystalline silicon solar cells, all coming from the same production line. The characterization sequence combines traditional global cell measurements (e.g., current–voltage, Suns- ${V}_{\text{OC}}$ ) with camera-based cell imaging of voltage distribution and power dissipation from photoluminescence and lock-in thermography, respectively. Spatial variations in current collection are visualized using a high-speed external quantum efficiency and reflectance measurement technique. A nondestructive transfer length method (TLM) measurement technique is also implemented, featuring circular TLM structures hidden within the busbars of the cells. The variance of individual loss parameters and their impact on cell performance are quantified for this large group of cells. Based on correlations performed across parameters, recombination losses in the bulk and rear surface of the cell are shown to be the primary limiting factor for the cell efficiency. The nature of these distributions and correlations provide important insights about loss mechanisms in industrial solar cells, helping to prioritize efforts for optimizing the performance of the production line. Additionally, many of the parameters extracted from these techniques can be tied back to incoming material quality issues (e.g., poor bulk carrier lifetime, nonuniform wafer doping) and to individual unit processes (e.g., texturing, phosphorus diffusion, silicon nitride deposition, metallization), allowing the data to be used directly for process control in manufacturing. All of the datasets are made available for download.