Xiaodong Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xiaodong Wang has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Xiulan Cheng
Advanced Electronic Materials and Devices, Shanghai Jiao Tong University, Shanghai 200240, China
4 shared publicationsXueling Quan
3 shared publicationsYaqian Li
Advanced Electronic Materials and Devices, Shanghai Jiao Tong University, Shanghai 200240, China
3 shared publications- Xiulan Cheng
Shanghai Jiao Tong University
2 shared publications - Xueling Quan
Center for Advanced Electronic Materials and Devices, Shanghai Jiao Tong University, Shanghai, China
2 shared publications Chong Shen
Center for Advanced Electronic Materials and Devices, Shanghai Jiao Tong University, Shanghai, China
1 shared publication
Latest Publications
- 2 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (19) , 1281-1284
Low Power and Compact Silicon Thermo-Optic Switch Based on Suspended Phase Arm Without Support Beams
A low power and compact thermo-optic switch based on 1 × 1 Mach-Zehnder interferometer structure is demonstrated with the thermal isolation structure fabricated with a new backside etching process. The adjacent SiO2 and underlying silicon around phase arm are removed to suppress the thermal diffusion. Benefiting from the backside anisotropic etching process and front protecting photoresist used in underlying silicon removal, there are no support SiO2 beams in air trenches avoiding about 10% of extra thermal diffusion. At 1550 nm for TE mode, a low switching power (Pπ) 0.48 mW is obtained with 450 μm thermooptic interaction length (LTO) representing a Pπ· LTO product of only 0.22 mW·mm, indicating a high thermal efficiency with a compact footprint. The 10% - 90% response time of the switch is 530 μs, including a rise time of 150 μs, and a fall time of 380 μs. Compared with the switch without isolation structure, the switching power of the proposed switch is reduced more than 17 times, needing only 5.6% of the original value.
- 2 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (19) , 1281-1284
Low Power and Compact Silicon Thermo-Optic Switch Based on Suspended Phase Arm Without Support Beams
A low power and compact thermo-optic switch based on 1 × 1 Mach-Zehnder interferometer structure is demonstrated with the thermal isolation structure fabricated with a new backside etching process. The adjacent SiO2 and underlying silicon around phase arm are removed to suppress the thermal diffusion. Benefiting from the backside anisotropic etching process and front protecting photoresist used in underlying silicon removal, there are no support SiO2 beams in air trenches avoiding about 10% of extra thermal diffusion. At 1550 nm for TE mode, a low switching power (Pπ) 0.48 mW is obtained with 450 μm thermooptic interaction length (LTO) representing a Pπ· LTO product of only 0.22 mW·mm, indicating a high thermal efficiency with a compact footprint. The 10% - 90% response time of the switch is 530 μs, including a rise time of 150 μs, and a fall time of 380 μs. Compared with the switch without isolation structure, the switching power of the proposed switch is reduced more than 17 times, needing only 5.6% of the original value.
- 1 April 2020
- Published by Elsevier in Microelectronic Engineering
- Vol. 227
Fast fabrication of silicon nanopillar array using electron beam lithography with two-layer exposure method
- 1 April 2020
- Published by Elsevier in Microelectronic Engineering
- Vol. 227
Fast fabrication of silicon nanopillar array using electron beam lithography with two-layer exposure method
- 25 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 31 (5) , 349-352
Silicon-Nitride-Assisted Edge Coupler Interfacing With High Numerical Aperture Fiber
Reducing the mode size mismatch between high-index-contrast silicon waveguide and single mode fiber takes an important role in photonic integration. A low-loss and broadband silicon nitride assisted edge coupler for coupling of light between silicon wire waveguides and high numerical aperture fiber is proposed and optimized for TE polarization. The mode size converter is composed of silicon inverse taper waveguides in core and two silicon nitride interlayers spaced by silica in cladding layers. The edge coupler is characterized with cleaved high numerical aperture fiber (mode field diameter is about 6.5 μm). With the help of refractive index matching oil (n = 1.46), the coupling loss for TE polarized light input is 0.35 dB at 1570 nm. The 1-dB bandwidth is 95 nm. The 1-dB alignment tolerances are higher than ± 2.5 μm and ± 1 μm in the horizontal and vertical directions, respectively, and higher than 25 μm in axial direction.
- 25 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 31 (5) , 349-352
Silicon-Nitride-Assisted Edge Coupler Interfacing With High Numerical Aperture Fiber
Reducing the mode size mismatch between high-index-contrast silicon waveguide and single mode fiber takes an important role in photonic integration. A low-loss and broadband silicon nitride assisted edge coupler for coupling of light between silicon wire waveguides and high numerical aperture fiber is proposed and optimized for TE polarization. The mode size converter is composed of silicon inverse taper waveguides in core and two silicon nitride interlayers spaced by silica in cladding layers. The edge coupler is characterized with cleaved high numerical aperture fiber (mode field diameter is about 6.5 μm). With the help of refractive index matching oil (n = 1.46), the coupling loss for TE polarized light input is 0.35 dB at 1570 nm. The 1-dB bandwidth is 95 nm. The 1-dB alignment tolerances are higher than ± 2.5 μm and ± 1 μm in the horizontal and vertical directions, respectively, and higher than 25 μm in axial direction.
- 1 January 2019
- Published by Optica Publishing Group
- p. JTh2A.64
Polarization Insensitive Racetrack Ring Resonator Based on Subwavelength Grating Slot Waveguides
A polarization-insensitive racetrack ring resonator using subwavelength grating slot waveguides has been demonstrated. The device can realize polarization-insensitive in three free spectral ranges around 1539.345 nm. The extinction ratios are higher than 18 dB.
- 1 January 2019
- Published by Optica Publishing Group
- p. JTh2A.64
Polarization Insensitive Racetrack Ring Resonator Based on Subwavelength Grating Slot Waveguides
A polarization-insensitive racetrack ring resonator using subwavelength grating slot waveguides has been demonstrated. The device can realize polarization-insensitive in three free spectral ranges around 1539.345 nm. The extinction ratios are higher than 18 dB.
- Open Access
- 4 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 10 (5) , 1-7
Ultra-Small and Fabrication-Tolerant Silicon Polarization Beam Splitter Using Sharp Bent Directional Coupler
An ultra-small polarization beam splitter on silicon-on-insulator platform is proposed and demonstrated experimentally employing a sharp bent directional coupler. The coupling length of our device is only 0.764 μ m. High-efficient selective coupling can be achieved benefiting from the inner bend chosen as Through port and ultra-small bend (radii are about 3 μ m) used in Through and Cross waveguides. The measured excess loss is less than 1 dB and extinction ratio is 15–20 dB for TM polarization, meanwhile, the measured excess loss is less than 2 dB and extinction ratio is 15-16 dB for TE polarization in a wavelength range from 1540 nm to 1580 nm. The fabrication tolerance to variation of waveguide width is also demonstrated. When the waveguide widths of the Through and Cross waveguides vary from −24 nm to +12 nm, the measured excess losses remain lower than 2 dB and the extinction ratios are higher than 10 dB for both polarizations. The footprint of the fabricated device is just 1.5 μ m × 1.3 μ m.
- 4 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 10 (5) , 1-7
Open AccessUltra-Small and Fabrication-Tolerant Silicon Polarization Beam Splitter Using Sharp Bent Directional Coupler
An ultra-small polarization beam splitter on silicon-on-insulator platform is proposed and demonstrated experimentally employing a sharp bent directional coupler. The coupling length of our device is only 0.764 μ m. High-efficient selective coupling can be achieved benefiting from the inner bend chosen as Through port and ultra-small bend (radii are about 3 μ m) used in Through and Cross waveguides. The measured excess loss is less than 1 dB and extinction ratio is 15–20 dB for TM polarization, meanwhile, the measured excess loss is less than 2 dB and extinction ratio is 15-16 dB for TE polarization in a wavelength range from 1540 nm to 1580 nm. The fabrication tolerance to variation of waveguide width is also demonstrated. When the waveguide widths of the Through and Cross waveguides vary from −24 nm to +12 nm, the measured excess losses remain lower than 2 dB and the extinction ratios are higher than 10 dB for both polarizations. The footprint of the fabricated device is just 1.5 μ m × 1.3 μ m.
- Open Access
- 1 January 2018
- Published by Wiley in Journal of Nanotechnology
- Vol. 2018, 1-9
Study on Surface-Enhanced Raman Scattering Substrate Based on Titanium Oxide Nanorods Coated with Gold Nanoparticles
A 3D surface-enhanced Raman scattering (SERS) substrate based on titanium oxide nanorods (TiOx-NRs) coated with gold nanoparticles (Au-NPs) was fabricated by a simple hydrothermal, no-template process. The nanostructure of TiOx-NRs influenced by the concentrations of hydrochloric (HCl) acid and sodium chloride (NaCl) was studied in detail. The substrate showed the strongest Raman enhancement, when the diameters of Au-NPs were around 40 nm and the gaps of Au-NPs were in the range of 5 nm to 10 nm. The surface electric field of our substrate was examined by finite-different time-domain (FDTD) solutions. Rhodamine 6G (R6G) was chosen as the probe molecule to study the SERS performance of the substrates. The Raman signal of 10−10 M R6G was detected clearly by the substrate with the enhancement factor of 2.64 × 108. All relative standard deviation (RSD) values of the major peaks for R6G were within the scope of 10.4% to 16.7%. The substrate could work efficiently even after immersed in water for one month.
- 1 January 2018
- Published by Wiley in Journal of Nanotechnology
- Vol. 2018, 1-9
Open AccessStudy on Surface-Enhanced Raman Scattering Substrate Based on Titanium Oxide Nanorods Coated with Gold Nanoparticles
A 3D surface-enhanced Raman scattering (SERS) substrate based on titanium oxide nanorods (TiOx-NRs) coated with gold nanoparticles (Au-NPs) was fabricated by a simple hydrothermal, no-template process. The nanostructure of TiOx-NRs influenced by the concentrations of hydrochloric (HCl) acid and sodium chloride (NaCl) was studied in detail. The substrate showed the strongest Raman enhancement, when the diameters of Au-NPs were around 40 nm and the gaps of Au-NPs were in the range of 5 nm to 10 nm. The surface electric field of our substrate was examined by finite-different time-domain (FDTD) solutions. Rhodamine 6G (R6G) was chosen as the probe molecule to study the SERS performance of the substrates. The Raman signal of 10−10 M R6G was detected clearly by the substrate with the enhancement factor of 2.64 × 108. All relative standard deviation (RSD) values of the major peaks for R6G were within the scope of 10.4% to 16.7%. The substrate could work efficiently even after immersed in water for one month.